Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY
RM32H0E _55 Steering _059604 STEERING COLUMN _0292296 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.INSTALL STEERING COLUMN ASSEMBLY (for LHD)

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each clamp to the steering column assembly.


c.

Engage the power steering ECU wire harness clamp.


d.

Connect the 2 power steering ECU connectors.


Hide 3.INSTALL STEERING COLUMN ASSEMBLY (for RHD)

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


b.

Connect each connector and engage each clamp to the steering column assembly.


c.

Engage the power steering ECU wire harness clamp.


d.

Connect the 2 power steering ECU connectors.


Hide 45260 4.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C365782C02
1.656,0.74 2.438,0.708 2.438,0.708 1.656,0.823 true 2.5,0.615 2.698,0.802 0.198,0.188 10 true *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Connect the No. 2 steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45260 5.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C365781C02
1.833,1.844 2.49,1.656 2.49,1.656 1.823,1.771 true 2.531,1.594 2.74,1.75 0.208,0.156 10 true *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Install the No. 2 steering intermediate shaft assembly to the steering gear assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45259A 6.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.
C365787

Engage the 2 claws to install the column hole cover silencer sheet.


b.
C365788C01
0,0 0,0 false
V113147

Engage in this direction


Engage the claw to close the column hole cover silencer sheet.


Hide 84340 7.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 87211 8.INSTALL NO. 1 AIR DUCT (for LHD)

a.

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.


Hide 87211A 9.INSTALL NO. 2 AIR DUCT (for RHD)

a.

Engage the 3 claws to install a new No. 2 air duct.


b.

Install the 2 bolts.


Hide 58816B 10.INSTALL CONSOLE BOX INSERT (for LHD)

Hide 58817A 11.INSTALL FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

Hide 12.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C369610C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws to install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly as shown in the illustration.


b.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 13.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C369609C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claw to install the upper steering column cover as shown in the illustration.


Hide 45287 14.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

If the lower steering column cover sub-assembly is installed in the incorrect order, the parts may break.


a.
C365789C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 3 claws to install the lower steering column cover sub-assembly as shown in the illustration.


b.

Engage the 4 claws.


c.

Install the 2 screws.


Hide 55545 15.INSTALL FUSE BOX OPENING COVER (w/o Knee Airbag)

Hide 55434B 16.INSTALL INSTRUMENT PANEL LOWER CENTER FINISH PANEL (w/o Knee Airbag)

Hide 55470 17.INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY (w/o Knee Airbag)

Hide 53601 18.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55404D 19.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55606 20.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 62112 21.INSTALL COWL SIDE TRIM BOARD LH (w/o Knee Airbag)

Hide 67914 22.INSTALL FRONT DOOR SCUFF PLATE LH (w/o Knee Airbag)

Hide 73900 23.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 24.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 25.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 26.INSTALL STEERING WHEEL ASSEMBLY

Hide 27.CHECK STEERING WHEEL CENTER POINT

Hide 45130 28.INSTALL HORN BUTTON ASSEMBLY

Hide 29. TORQUE SENSOR ZERO POINT CALIBRATION