Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for DENSO Made) › 2016.10–2019.09
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0299517 AIR CONDITIONING UNIT(for DENSO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for DENSO Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects / Inoperative when not performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
·

No. 1 air conditioning radiator damper servo sub-assembly

·

Air conditioning amplifier assembly


Initialize servo motor (Air conditioning system) DTCs are stored (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

Hide 55736D 6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 87246 9.DISCONNECT OUTLET HEATER WATER HOSE

a.
I112448

Slide the hose clip to disconnect the outlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 10.DISCONNECT INLET HEATER WATER HOSE

a.
I112449

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88707 11.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
I112450

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
I112451

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe subassembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 12.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A

a.
I112452

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 13.REMOVE FRONT SEAT ASSEMBLY LH

Hide 14.REMOVE FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55401E 15.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 16.REMOVE STEERING COLUMN ASSEMBLY

Hide 85940 17.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY

Hide 89340A 18.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 82878 19.REMOVE ECU INTEGRATION BOX LH

Hide 88625Q 20.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.
I112333

Disconnect the connector and air conditioning duct sub-assembly to remove the cooler thermistor (room temperature sensor).


Hide 55215D 21.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
I112334

Remove the 2 front floor carpet clips.


b.
I112453C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112454

Disengage the clips to remove the No. 3 dash panel insulator pad.


Hide 55307C 22.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I112345

Remove the 2 nuts and separate the relay block assembly.


b.
I113736

Remove the bolt to disconnect the ground wire.


c.

Disengage the clamps to disconnect the wire harness.


d.
I113737

Remove the bolt, screw, nut and No.2 instrument panel brace sub-assembly.


Hide 55306A 23.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.
I113738

Disengage the clamps to disconnect the wire harness.


b.
I113739

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.


Hide 55308B 24.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112457

Disengage the claws and clamp.


b.

Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 82141 25.DISCONNECT INSTRUMENT PANEL WIRE

a.

Disconnect each connector.

I113760C01
3.417,5.25 2.677,4.583 true 3.281,4.406 3.979,4.865 3.979,4.865 3.917,4.406 true 6.542,5.031 6.729,4.646 6.729,4.646 6.573,4.375 true 2.896,5.313 3.417,5.25 3.417,5.25 2.542,3.99 true 6.302,5.49 5.906,5.375 true 1.01,4.802 0.781,4.906 true 0.917,5.552 0.719,5.469 true 1.521,0.438 1.271,0.5 true 1.073,1.229 0.813,1 true 3.396,1.052 3.917,1.25 3.917,1.25 4.198,0.979 true 2.708,1.135 2.938,1.313 true 6.396,0.906 6.625,1.083 true 0.552,2.719 1.052,3 1.052,3 0.979,2.406 true 6.781,4.552 6.99,4.76 0.208,0.208 10 true *a 5.708,5.281 5.917,5.49 0.208,0.208 10 true *a 3.479,5.208 3.688,5.417 0.208,0.208 10 true *a 3.917,4.906 4.125,5.115 0.208,0.208 10 true *a 1.021,4.688 1.229,4.896 0.208,0.208 10 true *a 1.021,1.188 1.229,1.396 0.208,0.208 10 true *a 1.063,0.427 1.271,0.635 0.208,0.208 10 true *a 2.938,1.26 3.146,1.469 0.208,0.208 10 true *a 3.823,1.26 4.031,1.469 0.208,0.208 10 true *a 6.219,0.75 6.427,0.958 0.208,0.208 10 true *a 0.938,5.51 1.146,5.719 0.208,0.208 10 true *b 1.01,3.031 1.219,3.24 0.208,0.208 10 true *a 5.708,4.094 5.896,4.292 0.188,0.198 10 true A 5.688,4.365 5.844,4.542 0.156,0.177 10 true A
*a Clamp *b Hook



b.

Remove the bolt and screw.


c.

Remove the 4 bolts to disconnect the 4 ground wires.


d.

Remove the 2 nuts A.


e.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


f.

Disengage clamps and hook to disconnect the instrument panel wire.


Hide 88539J 26.DISCONNECT DRAIN COOLER HOSE

a.
I113742C03
0.958,3.208 0.688,3.01 true 0.969,3.188 1.188,3.354 0.219,0.167 10 true *1
*1 Cooler Unit Drain Hose Grommet


Disconnect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 27.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
I112482

Remove the 2 bolts.


b.

Remove the 5 bolts.

I113741


c.

Remove the nut.


d.
I112356

Disengage the clamps.


e.

Disconnect the 2 connectors.


f.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112484C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 28.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

I112485


Hide 55990B 29.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112479

Disengage the claws to remove the lower defroster nozzle assembly.