Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER (for RHD) › 2016.10–2019.09
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0299735 BRAKE BOOSTER(for RHD) A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the master cylinder sub-assembly from the brake booster assembly.


PROCEDURE

Hide 47201 1.REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Hide 31410 2.REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 47101A 3.REMOVE BRAKE PEDAL RETURN SPRING

Hide 4.LOOSEN CLEVIS LOCK NUT

a.
C142634C01
1.948,1.146 1.75,1.667 1.75,1.667 1.5,1.667 false 2.365,1.135 2.781,1.135 true 1.323,1.604 1.635,1.76 0.313,0.156 10 *1 2.833,1.073 3.146,1.229 0.313,0.156 10 *2
*1 Clevis Lock Nut
*2 Brake Master Cylinder Push Rod Clevis


Loosen the clevis lock nut of the brake master cylinder push rod clevis.


Hide 47264A 5.REMOVE PUSH ROD PIN

Hide 51441 6.REMOVE NO. 1 ENGINE UNDER COVER

Hide 55225 7.REMOVE DASH PANEL HEAT INSULATOR

a.
C366901

Remove the nut.


b.
C366879

Remove the 2 nuts and dash panel heat insulator.


Hide 44750 8.SEPARATE VACUUM HOSE ASSEMBLY

a.
C366881

Remove the 2 nuts and separate the vacuum hose assembly.


Hide 9.SEPARATE BRAKE TUBE

a.
C366885

Using a union nut wrench, disconnect the front No. 3 brake tube from the front brake flexible hose.


b.
C366882

Using a union nut wrench, disconnect the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube from the brake actuator assembly.


c.

Disengage the 11 clamps to remove the 2 No. 1 brake tube clamps from the front No. 1 brake tube, front No. 2 brake tube, front No. 3 brake tube and front No. 5 brake tube.


d.
C366883C01
1.49,1.5 1.323,1.771 1.323,1.771 1.208,1.438 true 1.667,1.063 1.354,0.76 true 1.25,1.813 1.49,2.031 0.24,0.219 10 true *1 1.125,0.646 1.333,0.865 0.208,0.219 10 true *2
*1 Brake Tube
*2 Clutch Tube


for Manual Transaxle:

i.

Disengage the clamp to separate the clutch tube from the 2 brake tube clamps.



e.

Disengage the 6 clamps to separate the 2 No. 2 brake tube clmaps from the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube.


f.
C372257

Disengage the 2 clamps to remove the No. 2 brake tube clamps from the vehicle body.


g.
C366884

Disengage the 3 clamps to remove the No. 1 brake tube clamp from the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube.


Hide 10.DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

a.
C366890

Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.


Hide 88707 11.SEPARATE SUCTION PIPE SUB-ASSEMBLY (for TMMT Made)

a.
C366888

Remove the 2 nuts and separate the suction pipe sub-assembly from the engine mounting sub-assembly and vehicle body.


Hide 88707 12.INSTALL SUCTION PIPE SUB-ASSEMBLY (for TMC Made)

a.
C366889

Disengage the 2 clamps to separate the suction pipe sub-assembly from the piping clamp.


Hide 44610 13.REMOVE BRAKE BOOSTER ASSEMBLY

a.
C366891

w/ Stop and Start System:

Disconnect the connector from the vacuum sensor assembly.


b.
C366892

w/ Vacuum Warning Switch:

i.

Disconnect the vacuum warning switch connector from the vacuum warning switch assembly.



c.
C366903C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the vehicle body.


d.
C366893

Remove the 4 nuts.


e.

Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.


f.
C366887

Move aside the front No. 1 brake tube, front No. 2 brake tube and front No. 3 brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the brake tubes.



g.

While pushing the suction pipe sub-assembly toward the bottom of the vehicle, remove the brake booster assembly.

NOTICE:
·

Do not apply excessive force to the brake tubes or refrigerant lines.

·

Do not apply excessive force to the suction pipe sub-assembly.




Hide 44785 14.REMOVE BRAKE BOOSTER GASKET

a.

Remove the brake booster gasket from the brake booster assembly.