Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2016.10–2019.09
RM32H0E _59 Vehicle Exterior _060313 LIGHTING (EXT) _0300012 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E357708E01
6.031,2.208 6.646,2.406 0.615,0.198 10 false TRLY 6.052,3.313 6.667,3.51 0.615,0.198 10 false RFGO 5.49,5.448 7.156,6.531 1.667,1.083 10 false Main Body ECU (Multiplex Network Body ECU) 3.229,5.208 5.219,5.708 1.99,0.5 10 false Instrument Panel Junction Block Assembly 0.844,5.292 2.438,5.823 1.594,0.531 10 false Rear Fog Light Assembly 0.865,5.135 1.479,5.333 0.615,0.198 10 false P7 0.896,4.479 1.51,4.677 0.615,0.198 10 false E 2.115,4.469 2.729,4.667 0.615,0.198 10 false B 2.333,4.458 2.948,4.656 0.615,0.198 10 false 1 0.719,4.469 1.333,4.667 0.615,0.198 10 false 2 3.177,4.406 3.792,4.604 0.615,0.198 10 false 21 3.177,4.583 3.792,4.781 0.615,0.198 10 false 3H 5.708,3.26 6.323,3.458 0.615,0.198 10 false 27 5.719,2.135 6.333,2.333 0.615,0.198 10 false 14 5.708,2.313 6.323,2.51 0.615,0.198 10 false MB 5.708,3.438 6.323,3.635 0.615,0.198 10 false MB 3.188,0.781 3.802,0.979 0.615,0.198 10 false 3K 3.177,0.615 3.792,0.813 0.615,0.198 10 false 1 1.969,0.958 2.583,1.156 0.615,0.198 10 false J/B-AM 0.354,0.792 1.708,1.146 1.354,0.354 10 false from Battery 3.958,1.333 4.573,1.531 0.615,0.198 10 false TAIL 4.771,1.74 5.385,1.938 0.615,0.198 10 false TAIL 3.708,4.01 4.323,4.208 0.615,0.198 10 false FOG RR 4.479,4.177 5.094,4.375 0.615,0.198 10 false FOG RR

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses and bulbs for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*1

*1: w/ Entry and Start System



PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog light ON/OFF Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light comes on.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

3.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (REAR FOG LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY OR BODY GROUND)
a.

Disconnect the P7 rear fog light assembly connector.


b.

Disconnect the 3H instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P7-1 (B) - 3H-21 Always Below 1 Ω
P7-1 (B) or 3H-21 - Body ground Always 10 kΩ or higher
P7-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the battery to terminal 3K-1.


d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

E259755C15
4.823,0.375 5.135,0.594 0.313,0.219 3.417,2.24 3.729,2.458 0.313,0.219 2.073,0.427 2.385,0.646 0.313,0.219 4.969,3.188 4.802,2.865 true 3.146,3.177 3.302,2.875 true 0.219,0.125 0.531,0.323 0.313,0.198 10 false *a 4.896,0.385 5.208,0.583 0.313,0.198 10 false 3H 3.469,2.25 3.781,2.448 0.313,0.198 10 false MB 4.833,3.208 5.313,3.406 0.479,0.198 10 false RFGO 2.927,3.198 3.406,3.396 0.479,0.198 10 false TRLY 2.135,0.448 2.521,0.802 0.385,0.354 10 false 3K
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
3H-21 - Battery negative (-) terminal Always 11 to 14 V



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

D

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY