Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.10–2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0300013 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to change the shift range between M1 and M7 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C311455E79
0.24,1.75 1.885,2.208 1.646,0.458 10 false from ECU-IG1 NO. 1 Fuse 3.635,2.229 4.25,2.427 0.615,0.198 10 false SFTU 3.635,2.823 4.25,3.021 0.615,0.198 10 false SFTD 3.885,1.656 4.5,1.854 0.615,0.198 10 false S 5.167,1.646 5.781,1.844 0.615,0.198 10 false S 5.146,2.24 5.76,2.438 0.615,0.198 10 false SFTU 5.146,2.833 5.76,3.031 0.615,0.198 10 false SFTD 2.5,3.427 3.115,3.625 0.615,0.198 10 false F17 2.5,3.594 4.552,3.99 2.052,0.396 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 5.604,3.844 6.219,4.042 0.615,0.198 10 false A38 5.604,4.01 6.104,4.292 0.5,0.281 10 false ECM 2.719,1.656 3.333,1.854 0.615,0.198 10 false IG 2.729,2.24 3.344,2.438 0.615,0.198 10 false E 2.563,1.656 2.875,1.854 0.313,0.198 10 false 4 2.563,2.24 2.875,2.438 0.313,0.198 10 false 2 4.938,2.833 5.25,3.031 0.313,0.198 10 false 43 4.938,2.24 5.25,2.438 0.313,0.198 10 false 42 4.938,1.646 5.25,1.844 0.313,0.198 10 false 59 4.063,1.656 4.375,1.854 0.313,0.198 10 false 5 4.063,2.229 4.375,2.427 0.313,0.198 10 false 1*2 4.063,2.823 4.375,3.021 0.313,0.198 10 false 3*2 6.042,2.042 6.5,2.24 0.458,0.198 10 false 12 V 6.042,2.625 6.5,2.823 0.458,0.198 10 false 12 V 0.167,4.156 1.24,4.354 1.073,0.198 10 false *1: for LHD 0.177,4.427 1.25,4.625 1.073,0.198 10 false *2: for RHD 4.063,2.063 4.375,2.26 0.313,0.198 10 false 3*1 4.063,2.667 4.375,2.865 0.313,0.198 10 false 1*1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))

B

2.READ VALUE USING GTS (SHIFT SW STATUS (S RANGE))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.

Powertrain > Engine > Data List
Tester Display
Shift SW Status (S Range)
50003 372 27

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift SW Status (S Range) Transmission control switch status ON or OFF
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)

B

7.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.READ VALUE USING GTS (SPORT SHIFT UP SW AND SPORT SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List.

Powertrain > Engine > Data List
Tester Display
Sport Shift Up SW
Sport Shift Down SW
50003 372 26,25

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sport Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sport Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C55
1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.969,1.781 2.125,1.979 0.156,0.198 10 false E 2.49,1.74 3.104,1.938 0.615,0.198 10 false SFTD*A 1.042,1.729 1.656,1.927 0.615,0.198 10 false SFTU*A 1.042,1.885 1.656,2.083 0.615,0.198 10 false SFTD*B 2.49,1.896 3.104,2.094 0.615,0.198 10 false SFTU*B
*A for LHD
*B for RHD
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for LHD):
Tester Connection Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher


Standard Resistance (for RHD):
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher



c.

Connect the F17 shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-43 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
A38-43 (SFTD) - Body ground Shift lever in M 10 kΩ or higher
A38-42 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
A38-42 (SFTU) - Body ground Shift lever in M 10 kΩ or higher



c.

Connect the A38 ECM connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C12
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M Below 1 Ω
4 (IG) - 5 (S) Shift lever not in M 10 kΩ or higher



c.

Connect the F17 shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH POWER SOURCE)

NG

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

8.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH POWER SOURCE)
a.
C267936C57
0.156,0.99 0.667,1.25 0.51,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.302,1.052 0.667,1.25 0.365,0.198 10 false F17 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the shift lock control unit assembly (transmission control switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F17-4 (IG) - Body ground Ignition switch ON 11 to 14 V
F17-4 (IG) - Body ground Ignition switch off Below 1 V



c.

Connect the shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

NG

INSPECT POWER SOURCE CIRCUIT

9.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the F17 shift lock control unit assembly (transmission control switch) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F17-5 (S) - A38-59 (S) Always Below 1 Ω
F17-5 (S) - Body ground and other terminals Always 10 kΩ or higher
A38-59 (S) - Body ground and other terminals Always 10 kΩ or higher



d.

Connect the A38 ECM connector.


e.

Connect the F17 shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT