Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for 3ZR-FAE)
RM32H0E _51 Engine / Hybrid System _059516 CRUISE CONTROL _0300549 CRUISE CONTROL SYSTEM(for 3ZR-FAE) C

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for 3ZR-FAE)  P1578  Brake System Malfunction  


DESCRIPTION

This DTC is stored when the vehicle stability control system has a problem. Check the vehicle stability control system when DTC P1578 is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
P1578 Brake System Malfunction When the ignition switch ON and the cruise control system is operating, a malfunction in the vehicle stability control system is detected for 0.2 seconds or more.
·

Vehicle stability control system

·

ECM

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:

Before replacing the ECM, refer to Service Bulletin.


PROCEDURE

1.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)
a.

Check for DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
OK:

Vehicle stability control system DTCs are not output.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)

NG

2.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 237

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control main switch (ON/OFF button).

3.

Push the cruise control main switch to -SET to begin control of vehicle speed using the cruise control system.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 237
OK:

DTC P1578 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.REPLACE ECM
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
4.CHECK FOR DTCs (CRUISE CONTROL SYSTEM)
a.

Clear the DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Clear DTCs
50002 237

b.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.

1.

Drive the vehicle at a speed for which cruise control operation is possible.

2.

Turn the cruise control system on using the cruise control main switch (ON/OFF button).

3.

Push the cruise control main switch to -SET to begin control of vehicle speed using the cruise control system.




c.

Check for DTCs.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (for 3ZR-FAE)>DTC CHECK / CLEAR

Powertrain > Cruise Control > Trouble Codes
50001 237
OK:

DTC P1578 is not output.



Result:
Proceed to
OK
NG



OK

END

NG