Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM32H0E _58 Vehicle Interior _060136 METER / GAUGE / DISPLAY _0294876 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Engine Oil Level Sensor Circuit  


DESCRIPTION

The combination meter assembly and engine oil level sensor are connected via direct line. The combination meter assembly determines the engine oil level based on the engine oil level sensor ON/OFF signal.

HINT:

As the engine oil level may be unstable when the engine is cold or running at high speeds, the combination meter assembly receives the coolant temperature signal and engine speed signal from the ECM via CAN communication in order to prevent the oil level warnings from being output erroneously.


WIRING DIAGRAM

C369239E06
1.979,1.448 2.438,1.646 0.458,0.198 10 false ECM 3.323,2.448 3.781,2.646 0.458,0.198 10 false LOIL 3.719,2.438 4.177,2.635 0.458,0.198 10 false 1 2.438,2.885 3.677,3.073 1.24,0.188 10 false C56 2.438,3.052 4.177,3.292 1.74,0.24 10 false Engine Oil Level Sensor 5.198,3.104 5.656,3.302 0.458,0.198 10 false F4 5.198,3.281 6.417,3.667 1.219,0.385 10 false Combination Meter Assembly 5.896,2.521 6.354,2.719 0.458,0.198 10 false I/F 5.198,2.438 5.656,2.635 0.458,0.198 10 false OILW 4.896,2.427 5.135,2.615 0.24,0.188 10 false 27 0.969,4.146 2.708,4.385 1.74,0.24 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

The following troubleshooting procedure is based on the assumption that the SFI system is normal. Confirm that the SFI system is not malfunctioning before performing the following procedure.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



PROCEDURE

1.INSPECT ENGINE OIL LEVEL SENSOR
a.

Remove the engine oil level sensor.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL LEVEL SENSOR>REMOVAL


b.

Inspect the engine oil level sensor.

Click hereEngine / Hybrid System>8NR-FTS (LUBRICATION)>OIL LEVEL SENSOR>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL LEVEL SENSOR - COMBINATION METER ASSEMBLY)
a.

Disconnect the F4 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-27 (OILW) - C56-1 (LOIL) Always Below 1 Ω
F4-27 (OILW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR