Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0298708 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System with Side-mounted Air Conditioner Pressure Sensor)  B1412  Ambient Temperature Sensor Circuit  


DESCRIPTION

The thermistor assembly is installed in front of the cooler condenser assembly to detect the ambient temperature, which is used to control the air conditioning system. This sensor is connected to the combination meter assembly and detects fluctuations in the ambient temperature. This data is used for controlling the cabin temperature. The sensor sends a signal to the combination meter assembly. The resistance of the thermistor assembly changes in accordance with the ambient temperature. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.

The combination meter assembly applies a voltage (5 V) to the thermistor assembly and reads voltage changes due to changes in the resistance of the thermistor assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B1412 Ambient Temperature Sensor Circuit When the air conditioning amplifier assembly cannot receive outside temperature sensor data from the combination meter assembly.
·

Thermistor assembly

·

Harness or connector between thermistor assembly and combination meter assembly

·

Air conditioning amplifier assembly

·

Combination meter assembly

·

CAN communication system


Memorized
(4 seconds or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


HINT:

If the ambient temperature is approximately -52.9°C (-63.22°F) or lower, DTC B1412/12 may be output even though the system is normal.


WIRING DIAGRAM

E357643E04
0.573,1.271 0.979,1.49 0.406,0.219 10 false A3 0.573,1.438 3.479,1.635 2.906,0.198 10 false Thermistor Assembly 2.219,0.438 2.625,0.656 0.406,0.219 10 false 2 2.219,0.792 2.625,1.01 0.406,0.219 10 false 1 2.625,0.438 3.031,0.656 0.406,0.219 10 false 34 2.635,0.792 3.042,1.01 0.406,0.219 10 false 35 2.938,0.438 3.344,0.656 0.406,0.219 10 false TEMP 2.938,0.792 3.344,1.01 0.406,0.219 10 false TX1+ 3.875,0.573 4.281,0.792 0.406,0.219 10 false I/F 3.427,1.354 4.542,1.552 1.115,0.198 10 false Micro Controller 3.458,1.823 4.573,2.021 1.115,0.198 10 false CAN Controller 3.427,2.469 4.542,2.667 1.115,0.198 10 false CAN Transceiver 3.51,3.604 4.625,3.802 1.115,0.198 10 false CAN I/F 3.042,4.823 5.156,5.115 2.115,0.292 10 false Combination Meter Assembly 3.042,4.667 3.74,4.854 0.698,0.188 10 false F4 4.552,3.5 5.667,3.698 1.115,0.198 10 false CANH 4.552,4.031 5.667,4.229 1.115,0.198 10 false CANL 5.083,3.5 5.333,3.698 0.25,0.198 10 false 32 5.083,4.031 5.333,4.229 0.25,0.198 10 false 31 5.5,4.031 5.75,4.229 0.25,0.198 10 false 12 5.51,3.5 5.76,3.698 0.25,0.198 10 false 11 5.813,3.656 6.927,3.854 1.115,0.198 10 false CANH 5.802,4.188 6.917,4.385 1.115,0.198 10 false CANL 5.49,4.813 7.063,5.198 1.573,0.385 10 false Air Conditioning Amplifier Assembly 5.49,4.646 5.927,4.927 0.438,0.281 10 false F73 0.823,5.25 2.938,5.542 2.115,0.292 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B



A

2.READ VALUE USING GTS (AMBIENT TEMPERATURE)

B

2.READ VALUE USING GTS (AMBIENT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Ambient Temperature Outside temperature Min.: -40°C (-40°F)
Max.: 87.5°C (189.5°F)
Almost the same as actual outside temperature The temperature displayed on the multi information display is -40 to 50°C (-40 to 122°F)
Body Electrical > Combination Meter > Data List
Tester Display
Ambient Temperature
50003 122 41
OK:

The display is as specified in the normal condition column.



Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C



A

3.INSPECT THERMISTOR ASSEMBLY

B

C

5.CHECK FOR DTC
3.INSPECT THERMISTOR ASSEMBLY


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

4.CHECK HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the A3 thermistor assembly connector.


b.

Disconnect the F4 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F4-34 (TEMP) - A3-2 Always Below 1 Ω
F4-35 (TX1+) - A3-1 Always Below 1 Ω
F4-34 (TEMP) or A3-2 - Body ground Always 10 kΩ or higher
F4-35 (TX1+) or A3-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK FOR DTC


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY