The No. 1 cooler thermistor (evaporator temperature sensor) is installed to the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator, which is used to control the air conditioning system. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor (evaporator temperature sensor) and reads voltage changes as the resistance of the No. 1 cooler thermistor (evaporator temperature sensor) changes. This sensor is used for frost prevention.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1413 | Evaporator Temperature Sensor Circuit | Any of the following conditions is met:
·
Open in No. 1 cooler thermistor (evaporator temperature sensor) circuit ·
Short in No. 1 cooler thermistor (evaporator temperature sensor) circuit |
·
No. 1 cooler thermistor (evaporator temperature sensor) ·
Air conditioning harness assembly ·
Air conditioning amplifier assembly |
Memorized
(4 seconds or more)* |
*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
| Vehicle Condition | |||
|---|---|---|---|
| Pattern 1 | Pattern 2 | ||
| Diagnosis Condition | Ignition switch ON | ○ | ○ |
| Malfunction Status | Open in No. 1 cooler thermistor (evaporator temperature sensor) circuit | ○ | - |
| Short in No. 1 cooler thermistor (evaporator temperature sensor) circuit | - | ○ | |
| Detection Time | 4 seconds or more | 4 seconds or more | |
| Number of Trips | 1 trip | 1 trip | |
DTC will be output when conditions for either of the patterns in the table above are met.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Evaporator Fin Thermistor | No. 1 Cooler Thermistor (Evaporator Temperature Sensor) | Min.: -29.70°C (-21.46°F)
Max.: 59.55°C (139.19°F) |
Actual evaporator temperature displayed | - |
| Tester Display |
|---|
| Evaporator Fin Thermistor |
The display is as specified in the normal condition column.
| Result | Proceed to |
|---|---|
| NG | A |
| OK (When troubleshooting according to Problem Symptoms Table) | B |
| OK (When troubleshooting according to the DTC) | C |
A
B
C
Remove the No. 1 cooler thermistor (evaporator temperature sensor).
Inspect the No. 1 cooler thermistor(evaporator temperature sensor).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the air conditioning harness assembly.
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for DENSO Made)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| *1 | Air Conditioning Harness Assembly | - | - |
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
*b | Front view of wire harness connector
(to No. 1 Cooler Thermistor (Evaporator Temperature Sensor)) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| m1-5 (SG-3) - ev-2 | Always | Below 1 Ω |
| m1-6 (TE) - ev-1 | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING UNIT (for DENSO Made)>DISASSEMBLY
Clear the DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B