Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P245211  Particulate Filter Pressure Sensor "A" Circuit Short to Ground  


DESCRIPTION

A differential pressure sensor is installed to monitor the pressure before the GPF (Gasoline Particulate Filter) catalyst converter. The sensor is a semiconductor type that is not affected by the exhaust gas. The differential pressure sensor outputs the difference between the atmospheric pressure and the pressure before the GPF catalyst.

A409082E01
1.729,3.375 1.104,3.302 true 1.542,2.469 0.979,2.844 true 2.615,0.323 2.229,0.573 true 2.385,1.115 2.115,1.219 true 0.417,1.052 1.417,1.25 1,0.198 10 false Exhaust Gas 2.646,0.25 3.083,0.49 0.438,0.24 10 false ECM 2,1.833 3.469,2.083 1.469,0.25 10 false Atmospheric Pressure 1.594,2.385 3.292,2.583 1.698,0.198 10 false GPF Catalyst 4.99,3.177 6.385,3.438 1.396,0.26 10 false Pressure (kPa [psi]) 3.813,0.604 4.604,0.854 0.792,0.25 10 false Voltage (V) 4.229,1.25 4.667,1.5 0.438,0.25 10 false 4.65 4.25,1.969 4.688,2.219 0.438,0.25 10 false 0.75 4.25,2.156 4.688,2.406 0.438,0.25 10 false 0.55 4.698,2.51 4.948,2.813 0.25,0.302 10 false -5 4.958,2.51 5.208,2.813 0.25,0.302 10 false 0 6,2.531 6.271,2.823 0.271,0.292 10 false 100 4.938,0.771 6.302,0.99 1.365,0.219 10 false Differential Pressure 2.438,1.052 3.719,1.427 1.281,0.375 10 false Differential Pressure Sensor 4.521,2.792 4.875,3 0.354,0.208 10 false [-0.7] 4.917,2.792 5.271,3 0.354,0.208 10 false [0] 5.948,2.813 6.635,3.031 0.688,0.219 10 false [14.5] 1.813,3.302 4.094,3.583 2.281,0.281 10 false Front Exhaust Pipe Assembly

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P245211 Particulate Filter Pressure Sensor "A" Circuit Short to Ground The output voltage from the differential pressure sensor is below 0.4 V for 3 seconds or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

ECM


Does not come on DTC stored SAE Code:
P2454

HINT:

When a DTC is output, check the Data List item "GPF Differential Pressure Sensor Bank 1 using the GTS.

DTC No. GPF Differential Pressure Sensor Bank 1 Malfunction
P245211 Approximately -5 kPa [-0.73 psi]
·

Short in PEX circuit to ground

·

Short in PEX circuit to EPX circuit

·

Open in VC circuit



If the Data List displays a normal value, the normal value may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

Example:

When the sensor output voltage is below 0.4 V for 3 seconds or more, the ECM stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P245211.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A404629E01
4.615,1.313 4.927,1.51 0.313,0.198 10 false 80 4.604,2.396 4.917,2.594 0.313,0.198 10 false 79 4.604,1.844 4.917,2.042 0.313,0.198 10 false 78 1.729,1.406 2.042,1.604 0.313,0.198 10 false VC 4.854,1.302 5.167,1.5 0.313,0.198 10 false VC 6.094,1.125 6.552,1.323 0.458,0.198 10 false 5 V 6.021,1.708 6.938,1.906 0.917,0.198 10 false 180 kΩ 4.854,1.875 5.313,2.073 0.458,0.198 10 false PEX 1.667,1.979 2.125,2.177 0.458,0.198 10 false PEX 4.823,2.417 5.438,2.615 0.615,0.198 10 false EPEX 1.76,2.51 2.073,2.708 0.313,0.198 10 false E2 2.01,1.333 2.167,1.531 0.156,0.198 10 false 3 2.021,1.844 2.177,2.042 0.156,0.198 10 false 2 2.01,2.396 2.167,2.594 0.156,0.198 10 false 1 5.708,3.417 6.167,3.615 0.458,0.198 10 false C62 5.729,3.615 6.188,3.813 0.458,0.198 10 false ECM 0.51,3.031 4.792,3.229 4.281,0.198 10 false Differential Pressure Sensor 0.521,2.823 0.979,3.021 0.458,0.198 10 false C73

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (DIFFERENTIAL PRESSURE SENSOR)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.
A404636

Disconnect the C73 differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Tester Connection Switch Condition Specified Condition
C73-3 (VC) - C73-1 (E2) Ignition switch ON 4.5 to 5.5 V
C73-2 (PEX) - C73-1 (E2) Ignition switch ON 0.5 to 3.0 V


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the voltage according to the value(s) in the table below.

Tester Connection Switch Condition Specified Condition
C73-3 (VC) - C73-2 (PEX) Ignition switch off 171 to 189 kΩ


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the C73 differential pressure sensor connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Tester Connection Condition Specified Condition
C73-3 (VC) - C62-80 (VC) Always Below 1 Ω
C73-2 (PEX) or C62-78 (PEX) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR