Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2018.05
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P008700  Fuel Rail / System Pressure - Too Low  


DESCRIPTION

The high-pressure direct injection fuel system consists of a spill control valve, check valve, fuel relief valve, fuel pressure sensor, fuel pump assembly (for high pressure side) and fuel injector assemblies. The spill control valve adjusts the return volume of high-pressure fuel. The check valve mechanically opens and closes the path to the fuel delivery pipe. The relief valve releases the fuel back to the fuel tank if there is a malfunction in the high-pressure fuel system. The fuel pump assembly (for high pressure side) is installed to the cylinder head cover and operated by a cam installed to the end of the exhaust camshaft. Rotation of the camshaft moves the pump plunger inside the fuel pump assembly (for high pressure side) up and down, pressurizing the fuel. The pressurized fuel opens the check valve and is pumped into the fuel delivery pipe. The ECM controls the spill control valve to adjust the fuel pressure between 2.4 and 20 MPa (24.5 and 204 kgf/cm2) and monitors signals from the fuel pressure sensor to maintain the target fuel pressure.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P008700 Fuel Rail / System Pressure - Too Low Although the ECM is not requesting the fuel pump (for high pressure side) to open the spill control valve, fuel pressure decreases 5 MPa (51.0 kgf/cm2, 725 psi) from target pressure for about 10 seconds (1 trip detection logic).
·

Leak of fuel

·

Fuel pipe (fuel tank - fuel pump assembly (for high pressure side))

·

Fuel pipe (fuel pump assembly (for high pressure side) - fuel injector assembly)

·

Fuel injector assembly

·

Fuel pump (for low pressure side)

·

Fuel delivery pipe (fuel pressure sensor)

·

Fuel system

·

ECM


Comes on DTC stored SAE Code:
P0087

MONITOR DESCRIPTION

If the fuel pressure decreases despite an increase request signal being sent to the fuel pump (for high pressure side) by the ECM, the ECM will illuminate the MIL and store this DTC.

MONITOR STRATEGY

Required Sensors/Components Fuel delivery pipe (fuel pressure sensor)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Record the freeze frame data.

5.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON.

8.

Turn the GTS on.

9.

Start the engine.

10.

Based on the engine speed, engine load and other conditions displayed in the freeze frame data, reproduce the conditions present when the DTC was stored.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P008700.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FUEL LEAK
a.

Check around and beneath the car for fuel leaks, fumes, etc.

OK:

No fuel leaks present.



Result:
Proceed to
OK
NG



OK

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)

NG

REPAIR OR REPLACE FUEL LEAK POINT

2.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P008700)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

e.

Read the DTCs.

Result:
Result Proceed to
DTC P008700 is output A
DTC P008700 and other DTCs are output B


HINT:

If any DTCs other than P008700 are output, troubleshoot those DTCs first.




A

3.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

3.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?


Result:
Proceed to
YES
NO



YES

DTC CAUSED BY RUNNING OUT OF FUEL

NO

4.READ VALUE USING GTS (MISFIRE COUNT CYLINDER (INSPECT FUEL INJECTOR ASSEMBLY))
4.READ VALUE USING GTS (MISFIRE COUNT CYLINDER (INSPECT FUEL INJECTOR ASSEMBLY))
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / Misfire Count Cylinder #1 to Misfire Count Cylinder #4.

Powertrain > Engine > Data List
Tester Display
Misfire Count Cylinder #1
Misfire Count Cylinder #2
Misfire Count Cylinder #3
Misfire Count Cylinder #4
50003 372 148,149,150,151

e.

Monitor all of the misfire count that are displayed on the GTS.

Result:
Misfire Count Proceed to
There are no misfire counts A
3 cylinders or more have misfire counts
1 or 2 cylinders have misfire counts B


HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

5.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)

B

REPLACE FUEL INJECTOR ASSEMBLY

5.READ VALUE USING GTS (HIGH FUEL PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / All Data / High Fuel Pressure Sensor.

Powertrain > Engine > Data List
Tester Display
High Fuel Pressure Sensor
50003 372 47

e.

Check that the fuel pressure fluctuates when the engine condition changes from idling to racing.

Result:
Result Proceed to
Fuel pressure does not rise A
Fuel pressure fluctuates B
Fuel pressure does not fluctuate C




A

6.CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)

B

8.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

C

REPLACE FUEL DELIVERY PIPE (FUEL PRESSURE SENSOR)

6.CHECK FUEL PUMP OPERATION (FOR LOW PRESSURE SIDE)
a.

Check the fuel pump operation (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)

NG

7.CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
a.

Check the fuel pressure (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

8.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)

NG

REPAIR OR REPLACE FUEL SYSTEM (PRESSURE REGULATOR, PIPE LINE AND FILTER)

8.REPLACE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (FOR HIGH PRESSURE SIDE)
a.

Replace the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for High Pressure)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump assembly (for high pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

9.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)
9.CHECK IF DTC OUTPUT RECURS (SEE IF DTC P008700 IS OUTPUT AGAIN)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

j.

Read the DTCs.

Result:
Result Proceed to
DTC P008700 is output A
DTCs are not output B




A

B

END