Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2016.10–2019.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM J

8NR-FTS ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump (for low pressure side) and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump control ECU adjust the fuel pump operation speed.

WIRING DIAGRAM

A384833E03
1.135,0.292 1.292,0.49 0.156,0.198 10 false B 1.135,1.323 1.292,1.521 0.156,0.198 10 false E 3.385,1.427 3.844,1.625 0.458,0.198 10 false FP- 3.427,0.385 3.885,0.583 0.458,0.198 10 false FP 3.427,1.833 3.583,2.031 0.156,0.198 10 false E 4.198,0.646 4.656,0.844 0.458,0.198 10 false FPC 4.302,1.833 4.76,2.031 0.458,0.198 10 false +B 3.292,2.333 4.865,2.583 1.573,0.25 10 false Fuel Pump Control ECU 6.094,0.552 6.552,0.75 0.458,0.198 10 false FPC 6.094,4.917 6.635,5.104 0.542,0.188 10 false MREL 6.375,5.635 6.917,5.823 0.542,0.188 10 false A38 0.677,5.917 1.323,6.135 0.646,0.219 10 false Battery 3.292,2.177 3.667,2.396 0.375,0.219 10 false M68 3.219,1.729 3.375,1.927 0.156,0.198 10 false 4 3.229,1.25 3.385,1.438 0.156,0.188 10 false 5 3.219,0.26 3.375,0.448 0.156,0.188 10 false 6 4.604,1.719 4.76,1.917 0.156,0.198 10 false 1 4.594,0.531 4.75,0.729 0.156,0.198 10 false 2 5.75,0.427 5.948,0.625 0.198,0.198 10 false 21 5.823,4.938 6.031,5.135 0.208,0.198 10 false 46 6.375,5.792 6.917,5.979 0.542,0.188 10 false ECM 1.417,0.604 1.729,0.802 0.313,0.198 10 false *1 1.396,1.677 1.708,1.875 0.313,0.198 10 false *1 1.469,0.188 1.625,0.385 0.156,0.198 10 false 4 1.865,0.188 2.021,0.385 0.156,0.198 10 false 4 1.354,0.365 1.813,0.563 0.458,0.198 10 false M14 1.385,1.438 1.844,1.635 0.458,0.198 10 false M14 1.781,0.385 2.24,0.583 0.458,0.198 10 false M75 1.792,1.448 2.25,1.646 0.458,0.198 10 false M75 1.448,1.25 1.604,1.448 0.156,0.198 10 false 5 1.844,1.25 2,1.448 0.156,0.198 10 false 5 1.823,1.667 2.135,1.865 0.313,0.198 10 false *2 1.813,0.604 2.125,0.802 0.313,0.198 10 false *2 2.896,2.885 3.052,3.083 0.156,0.198 10 false 5 3.802,2.906 3.927,3.188 0.125,0.281 10 false 3 2.906,3.479 3.063,3.677 0.156,0.198 10 false 2 3.792,3.5 3.948,3.698 0.156,0.198 10 false 1 2.625,4.802 2.781,5 0.156,0.198 10 false 3 4.063,4.792 4.219,4.99 0.156,0.198 10 false 4 2.625,5.406 2.781,5.604 0.156,0.198 10 false 6 4.083,5.396 4.24,5.594 0.156,0.198 10 false 5 3.073,5.823 4.01,6.104 0.938,0.281 10 false EFI-MAIN 0.469,5.042 1.271,5.385 0.802,0.344 10 false BATT MAIN 0.833,4.615 2.823,4.813 1.99,0.198 10 false EFI-MAIN NO. 1 1.208,3.156 3.198,3.354 1.99,0.198 10 false EFI-MAIN NO. 2 2.938,3.917 4.927,4.115 1.99,0.198 10 false EFI-MAIN NO. 2 2.771,6.302 3.083,6.5 0.313,0.198 10 false 1B 2.802,6.448 4.333,6.729 1.531,0.281 10 false No. 1 Integration Relay 0.771,0.604 0.927,0.802 0.156,0.198 10 false 1 0.781,1.135 0.938,1.333 0.156,0.198 10 false 2 5.115,6.052 5.969,6.385 0.854,0.333 10 false *1: for 2WD 5.115,6.385 5.948,6.698 0.833,0.313 10 false *2: for AWD 0.458,1.781 1.24,1.99 0.781,0.208 10 false Fuel Pump 0.438,1.958 1.875,2.146 1.438,0.188 10 false (for Low Pressure Side)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE CIRCUIT RELAY)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

e.

Check whether operating sounds can be heard while operating the fuel pump (for low pressure side) using the GTS.

OK:

Operating sounds can be heard from the fuel pump (for low pressure side).



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO, ACTIVATE THE CIRCUIT RELAY)

NG

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
2.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO, ACTIVATE THE CIRCUIT RELAY)
A240046C01
1.25,1.573 1.5,0.99 true 2.271,1.604 1.958,0.99 true 0.146,0.104 0.458,0.302 0.313,0.198 10 *a 1.219,1.615 1.375,1.813 0.156,0.198 10 1 2.26,1.625 2.417,1.823 0.156,0.198 10 2
*a Component with harness connected
(Fuel Pump [for Low Pressure Side])


a.

Remove the fuel pump (for low pressure side) from the fuel tank assembly.

for 2WD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>REMOVAL

for AWD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>REMOVAL


b.

Clean the fuel pump to completely remove any remaining fuel.


c.

Connect the fuel pump connector.

CAUTION:

Make sure that there is no fuel remaining inside or on the outside of the fuel pump.



d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty Ratio
50004 372 10

h.

Operate the fuel pump (for low pressure side) using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
2 - 1 Fuel pump duty ratio: 25% 3.2 to 4.05 V
Fuel pump duty ratio: 80% 8.8 to 12.5 V



i.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Circuit Relay.

Powertrain > Engine > Active Test
Tester Display
Activate the Circuit Relay
50004 372 24

j.

Operate the fuel pump (for low pressure side) using the Active Test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection GTS Operation Specified Condition
2 - 1 ON (Fuel pump duty ratio: 90%) 9.0 to 14.0 V


HINT:
·

Be sure to measure the voltage with all the connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Result Proceed to
OK (for 2WD) A
OK (for AWD) B
NG (for 2WD) C
NG (for AWD) D



A

3.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

B

6.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

C

10.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

D

14.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
3.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Inspect the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>INSPECTION


Result:
Proceed to
OK
NG



OK

END

NG

4.REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
4.REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Replace the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

6.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Inspect the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>INSPECTION


Result:
Proceed to
OK
NG



OK

END

NG

7.REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
7.REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Replace the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
A256531C12
0.573,1.125 1.031,1.406 0.458,0.281 1.302,1.5 1.198,1.823 true 1.802,1.5 1.896,1.823 true 0.667,1.167 1.167,1.604 0.5,0.438 10 false M68 0.135,0.156 0.667,0.521 0.531,0.365 10 false *a 1.073,1.854 1.438,2.104 0.365,0.25 10 false +B 1.875,1.854 2.198,2.094 0.323,0.24 10 false E
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


a.

Disconnect the fuel pump control ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
M68-1 (+B) - M68-4 (E) Ignition switch ON 11 to 14 V



Result:
Result Proceed to
OK (for 2WD) A
OK (for 2WD) B
NG C



A

10.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

B

14.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)

C

18.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
10.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Inspect the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

11.CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the M14 fuel pump (for low pressure side) connector.


b.

Disconnect the M68 fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M14-4 (B) - M68-6 (FP) Always Below 1 Ω
M14-5 (E) - M68-5 (FP-) Always Below 1 Ω
M14-4 (B) - M68-6 (FP) - Body ground and other terminals Always 10 kΩ or higher
M14-5 (E) - M68-5 (FP-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the M68 fuel pump control ECU assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M68-2 (FPC) - A38-21 (FPC) Always Below 1 Ω
M68-2 (FPC) or A38-21 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO (INSPECT ECM))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO (INSPECT ECM))
A290250C23
0.458,1.115 0.833,1.365 0.375,0.25 1.594,1.844 1.5,1.552 true 0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.542,1.156 1,1.354 0.458,0.198 10 false M68 1.521,1.865 1.833,2.063 0.313,0.198 10 false FPC
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


a.

Disconnect the fuel pump control ECU assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty Ratio
50004 372 10

f.

Operate the fuel pump control ECU assembly using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
M68-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

14.INSPECT FUEL PUMP (FOR LOW PRESSURE SIDE)
a.

Inspect the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

REPLACE FUEL PUMP (FOR LOW PRESSURE SIDE)

15.CHECK HARNESS AND CONNECTOR (FUEL PUMP (FOR LOW PRESSURE SIDE) - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Disconnect the M75 fuel pump (for low pressure side) connector.


b.

Disconnect the M68 fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M75-4 (B) - M68-6 (FP) Always Below 1 Ω
M75-5 (E) - M68-5 (FP-) Always Below 1 Ω
M75-4 (B) - M68-6 (FP) - Body ground and other terminals Always 10 kΩ or higher
M75-5 (E) - M68-5 (FP-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the M68 fuel pump control ECU assembly connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M68-2 (FPC) - A38-21 (FPC) Always Below 1 Ω
M68-2 (FPC) or A38-21 (FPC) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO (INSPECT ECM))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP DUTY RATIO (INSPECT ECM))
A290250C24
0.458,1.115 0.833,1.365 0.375,0.25 1.594,1.844 1.5,1.552 true 0.156,0.104 0.469,0.26 0.313,0.156 10 false *a 0.542,1.156 1,1.354 0.458,0.198 10 false M68 1.521,1.865 1.833,2.063 0.313,0.198 10 false FPC
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


a.

Disconnect the fuel pump control ECU assembly connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty Ratio.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty Ratio
50004 372 10

f.

Operate the fuel pump control ECU assembly using the Active Test function and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection GTS Operation Specified Condition
M68-2 (FPC) - Body ground Before Active Test → During Active Test Before Active Test: Resistance is stable → During Active Test: Resistance fluctuates*


HINT:

*: Using the Active Test, duty control of the transistors in the ECM will be performed. Due to the duty control, resistance of the FPC terminal will be unstable during the Active Test. If the resistance is stable before the Active Test and fluctuates while performing the Active Test, it can be determined that the transistor is operating. If the transistor does not operate during the Active Test, the ECM may be malfunctioning.



Result:
Proceed to
OK
NG



OK

REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

18.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the M68 fuel pump control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M68-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - FUEL PUMP CONTROL ECU ASSEMBLY)
a.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Disconnect the M68 fuel pump control ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (EFI-MAIN NO. 2 relay holder) - M68-1 (+B) Always Below 1 Ω
3 (EFI-MAIN NO. 2 relay holder) or M68-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.CHECK TERMINAL VOLTAGE (EFI-MAIN NO. 2 RELAY VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.CHECK TERMINAL VOLTAGE (EFI-MAIN NO. 2 RELAY VOLTAGE)
a.
A384860C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 0.24,1.573 0.552,1.771 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO. 2 Relay Holder


Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 2 relay holder) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

21.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - EFI-MAIN NO. 2 RELAY)

21.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 2 RELAY - BODY GROUND)
a.
A384860C01
0.125,0.073 0.438,0.271 0.313,0.198 10 false *1 0.24,1.573 0.552,1.771 0.313,0.198 10 false *2
*1 No. 1 Engine Room Relay Block
*2 EFI-MAIN NO. 2 Relay Holder


Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (EFI-MAIN NO. 2 relay holder) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

22.INSPECT EFI-MAIN NO. 2 RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

22.INSPECT EFI-MAIN NO. 2 RELAY

Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI-MAIN NO. 2 RELAY)

NG

REPLACE EFI-MAIN NO. 2 RELAY

23.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - EFI-MAIN NO. 2 RELAY)
a.

Disconnect the 1B No. 1 integration relay connector.


b.

Remove the EFI-MAIN NO. 2 relay from the No. 1 engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-4 - 1 (EFI-MAIN NO. 2 relay holder) Always Below 1 Ω
1B-4 or 1 (EFI-MAIN NO. 2 relay holder) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR