The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection duration. If the air fuel ratio sensor (sensor 1) malfunctions, the ECM is unable to control the air fuel ratio accurately.
The air fuel ratio sensor (sensor 1) is a planar type and integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are a narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, therefore sensor activation is accelerated.
In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.
*: Value changes inside the ECM. Since the air fuel ratio sensor (sensor 1) is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor (sensor 1) or ECM connectors will show a constant voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P21951D | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Circuit Current Out of Range | While the fuel cut operation is performed (during vehicle deceleration), the air fuel ratio sensor (sensor 1) current is 2.2 mA or higher for 3 seconds or more (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on (Euro-OBD)/- (Except Euro-OBD) | DTC stored (Euro-OBD)/- (Except Euro-OBD) | SAE Code:
P2195 |
| P219523 | A/F (O2) Sensor Signal Biased/Stuck Lean Bank 1 Sensor 1 Signal Stuck Low | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio Air fuel ratio sensor (sensor 1) voltage is higher than 3.8 V. (b) Heated oxygen sensor voltage is 0.21 V or higher. |
·
Open or short in air fuel ratio Air sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pump (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly ·
Fuel system ·
ECM |
Comes on (Euro-OBD)/- (Except Euro-OBD) | DTC stored (Euro-OBD)/- (Except Euro-OBD) | SAE Code:
P2195 |
| P21961D | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Circuit Current Out of Range | While the fuel cut operation is performed (during vehicle deceleration), the air fuel ratio sensor (sensor 1) current is less than 0.47 mA for 3 seconds or more (2 trip detection logic). | ·
Air fuel ratio sensor (sensor 1) ·
ECM |
Comes on (Euro-OBD)/- (Except Euro-OBD) | DTC stored (Euro-OBD)/- (Except Euro-OBD) | SAE Code:
P2196 |
| P219624 | A/F (O2) Sensor Signal Biased/Stuck Rich Bank 1 Sensor 1 Signal Stuck High | Both of the following conditions are met for 5 seconds or more (2 trip detection logic):
(a) Air fuel ratio sensor (sensor 1) voltage is less than 2.8 V. (b) Heated oxygen sensor voltage is less than 0.71 V. |
·
Open or short in air fuel ratio sensor (sensor 1) circuit ·
Air fuel ratio sensor (sensor 1) ·
Intake system ·
Gas leak from exhaust system ·
Fuel pressure (for low pressure side) ·
Fuel pressure (for high pressure side) ·
Fuel injector assembly ·
Fuel system ·
ECM |
Comes on (Euro-OBD)/- (Except Euro-OBD) | DTC stored (Euro-OBD)/- (Except Euro-OBD) | SAE Code:
P2196 |
When any of these DTCs are stored, check the air fuel ratio sensor (sensor 1) voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Voltage B1S1.
Short-term fuel trim values can also be read using the GTS.
The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor (sensor 1) voltage output cannot be confirmed without using the GTS.
If an air fuel ratio sensor malfunction is detected, the ECM will store a DTC.
Under air fuel ratio feedback control, If the air fuel ratio sensor (sensor 1) output voltage is less than 2.8 V (very rich condition) for 5 seconds despite the heated oxygen sensor (sensor 1) output voltage being less than 0.71 V, the ECM stores DTC P219624. Alternatively, if the air fuel ratio sensor output voltage is higher than 3.8 V (very lean condition) for 5 seconds despite the heated oxygen sensor output voltage being 0.21 V or higher, DTC P219523 is stored.
A rich air fuel mixture causes a low air fuel ratio sensor (sensor 1) current, and a lean air fuel mixture causes a high air fuel ratio sensor (sensor 1) current. Therefore, the sensor output becomes low during acceleration, and it becomes high during deceleration with the throttle valve fully closed. The ECM monitors the air fuel ratio sensor (sensor 1) current during fuel cut and detects any abnormal current values.
If the air fuel ratio sensor output is 2.2 mA or higher for 3 seconds or more of cumulative time, the ECM interprets this as a malfunction in the air fuel ratio sensor (sensor 1) and stores DTC P21951D (stuck on high side). If the air fuel ratio sensor (sensor 1) output is less than 0.47 mA for 3 seconds or more of cumulative time, the ECM stores DTC P21961D (stuck on low side).
| Required Sensors/Components (Main) | Air fuel ratio sensor (sensor 1) |
| Required Sensors/Components (Related) | Heated oxygen sensor |
| Frequency of Operation | Continuous: Sensor voltage detection monitor
Once per driving cycle: Sensor current detection monitor |
| Duration | 3 seconds: Sensor current detection monitor
5 seconds: Sensor voltage detection monitor |
| Time after engine start | 30 seconds or more |
| Fuel system status | Closed loop |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa(abs) [11.02 psi(abs)] or higher |
| Air fuel ratio sensor (sensor 1) status | Activated |
| Continuous time of fuel cut | 3 seconds to 10 seconds |
| Heated oxygen sensor voltage | 0.21 V or higher |
| Air fuel ratio sensor (sensor 1) voltage | Higher than 3.8 V |
| Heated oxygen sensor voltage | Less than 0.71 V |
| Air fuel ratio sensor (sensor 1) voltage | Less than 2.8 V |
| Air fuel ratio sensor (sensor 1) current | 2.2 mA or higher |
| Air fuel ratio sensor (sensor 1) current | Less than 0.47 mA |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
Drive the vehicle at a speed between 75 and 100 km/h (47 and 62 mph) for at least 10 minutes [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
With shift state M selected (for CVT) or second gear (for Manual Transaxle) [C], accelerate the vehicle to 75 km/h (47 mph) or more by depressing the accelerator pedal for at least 10 seconds [D].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Soon after performing step [D] above, release the accelerator pedal for at least 4 seconds without depressing the brake pedal in order to execute fuel cut control [E].
Allow the vehicle to decelerate until the vehicle speed decreases to less than 10 km/h (6 mph).
Repeat steps [C] through [E] above at least 3 times in one driving cycle.
Enter the following menus: Powertrain / Engine / Trouble Codes [F].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [B] through [F] again.
Refer to DTC P003012.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003012
Inspect the fuses for circuits related to this system before performing the following procedure.
A low air fuel ratio sensor (sensor 1) voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
A high air fuel ratio sensor (sensor 1) voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P21951D, P219523, P21961D or P219624 is output | A |
| DTC P21951D, P219523, P21961D or P219624 and P013613, P013617 or P01361C are output | |
| DTC P21951D, P219523, P21961D or P219624 and other DTCs are output | B |
If any DTCs relating to the air fuel ratio sensor (sensor 1) (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor (sensor 1) admittance) are output, troubleshoot those DTCs first.
A
B
Has the vehicle run out of fuel in the past?
| Proceed to |
|---|
| YES |
| NO |
YES
NO
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output) |
B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Enter the following menus: Powertrain / Engine / Data List / All Data / A/F (O2) Sensor Current B1S1.
| Tester Display |
|---|
| A/F (O2) Sensor Current B1S1 |
Check the test value of the air fuel ratio sensor (sensor 1) output current during fuel cut, referring to the Driving Pattern Detail for [C] through [E] in the Confirmation Driving Pattern.
To measure the air fuel ratio sensor (sensor 1) current precisely, perform the fuel cut operation as long as possible.
If it is difficult to measure the air fuel ratio sensor (sensor 1) current, use the snapshot function of the GTS.
| Test Value | Proceed to |
|---|---|
| Within normal range
(0.47 mA or higher, and less than 2.2 mA) |
A |
| Outside normal range
(less than 0.47 mA, or 2.2 mA or higher) |
B |
A
B
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume for A/F Sensor / Data List / All Data / A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2.
| Active Test Display |
|---|
| Control the Injection Volume for A/F Sensor |
| Data List Display |
|---|
| A/F (O2) Sensor Voltage B1S1 |
| O2 Sensor Voltage B1S2 |
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2) displayed on the GTS.
The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 12.5%.
The air fuel ratio sensor (sensor 1) has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
|---|---|---|---|
| A/F (O2) Sensor Voltage B1S1
(Air fuel ratio) |
12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2 Sensor Voltage B1S2
(Heated oxygen) |
12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of A/F (O2) Sensor Voltage B1S1 | Status of O2 Sensor Voltage B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
|---|---|---|---|
| Lean | Lean | Actual air fuel ratio lean | A |
| Rich | Rich | Actual air fuel ratio rich | |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | |
| Lean/Rich | Lean/Rich | Normal |
Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor (sensor 1) output voltage (A/F (O2) Sensor Voltage B1S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2 Sensor Voltage B1S2) is consistently below 0.4 V.
Rich: During Control the Injection Volume for A/F Sensor, the A/F (O2) Sensor Voltage B1S1 is consistently below 3.1 V, and the O2 Sensor Voltage B1S2 is consistently higher than 0.55 V.
Lean/Rich: During Control the Injection Volume for A/F Sensor, the output voltage of the air fuel ratio sensor or heated oxygen sensor alternates correctly.
Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1 and O2 Sensor Voltage B1S2].
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
A
B
Check the intake system for vacuum leaks.
Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION
No leaks in the intake system.
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for exhaust gas leaks.
No gas leaks.
Perform "Inspection After Repair" after repairing or replacing the exhaust system.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the fuel pressure (for low pressure side).
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Data List / All Data / High Fuel Pressure Sensor.
| Tester Display |
|---|
| High Fuel Pressure Sensor |
Read the values.
| GTS Display | Condition | Specified Condition |
|---|---|---|
| High Fuel Pressure Sensor | Shift lever position: P or N (neutral)
A/C: Off Engine idling |
4 to 18 MPa |
| Shift lever position: P or N (neutral)
A/C: Off Engine speed: 3000 rpm |
8 to 18 MPa |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the fuel injector assembly.
Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL INJECTOR>INSPECTION
Perform "Inspection After Repair" after replacing the fuel injector assembly.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output) |
B |
A
B
Replace the ECM.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the fuel pump (for low pressure side).
for 2WD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for 2WD)>INSPECTION
for AWD: Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL PUMP (for AWD)>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 2WD) | B |
| NG (for AWD) | C |
A
B
C
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "Inspection After Repair" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
| Tester Display |
|---|
| All Readiness |
Input the DTC: P21951D, P219523, P21961D or P219624.
Check the DTC judgment result.
| Result | Proceed to |
|---|---|
| NORMAL
(DTCs are not output) |
A |
| ABNORMAL
(DTC P21951D, P219523, P21961D or P219624 is output) |
B |
A
B