Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

E360100E02
4.906,2.188 6.594,2.76 1.688,0.573 10 false Radio and Display Receiver Assembly 4.927,2.01 5.542,2.208 0.615,0.198 10 false F131 5.083,1.542 5.698,1.74 0.615,0.198 10 false MIN- 5.073,0.708 5.688,0.906 0.615,0.198 10 false SNS2 4.813,1.385 5.125,1.583 0.313,0.198 10 false 22 4.833,0.594 5.146,0.792 0.313,0.198 10 false 25 2.146,0.583 2.458,0.781 0.313,0.198 10 false 1 2.167,1.375 2.479,1.573 0.313,0.198 10 false 7 1.646,1.479 2.365,1.719 0.719,0.24 10 false MCO- 1.677,0.698 2.396,0.938 0.719,0.24 10 false SNS2 0.865,2.156 2.865,2.76 2,0.604 10 false Map Light Assembly (Telephone Microphone Assembly) 0.875,2 1.49,2.198 0.615,0.198 10 false R2

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E426527C02
1.458,0.521 1.875,0.813 0.417,0.292 2.073,1.99 2.365,2.615 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.51,0.583 1.917,0.823 0.406,0.24 10 false F131 2.365,2.635 2.771,2.875 0.406,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).


b.
E358190C03
2.302,1.094 2.719,0.677 true 2.281,1.438 2.625,1.781 true 0.177,0.156 0.49,0.354 0.313,0.198 10 false *a 2.792,0.521 3.229,0.802 0.438,0.281 10 false SNS2 2.698,1.74 3.167,2.042 0.469,0.302 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for TMC Made) B
NG (for TMMT Made) C



A

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

C

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)