Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM C

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  B1543  Extension Module Disconnected 2  


DESCRIPTION

If the radio and display receiver assembly cannot detect the navigation ECU for a certain period of time (90 seconds) after the ignition switch is turned ACC and the radio and display receiver assembly confirms that the information is missing by checking past navigation ECU recognition information (registered information), this DTC will be stored.

HINT:

The Navigation system uses USB communication between devices. If an open, short, short to +B or short to ground occurs in the USB circuit, communication is interrupted and the Navigation system will not operate normally.


DTC No. Detection Item DTC Detection Condition Trouble Area
B1543 Extension Module Disconnected 2 Navigation ECU disconnected
·

Navigation ECU

·

Radio and display receiver assembly

·

Harness or connector

·

No. 1 Navigation Wire*



*: for TMC Made


HINT:

This DTC may be stored due to environmental reasons such as electrical noise or interference.


WIRING DIAGRAM

E402231E11
5.323,2.302 7.042,2.792 1.719,0.49 10 false Radio and Display Receiver Assembly 5.344,2.104 5.792,2.417 0.448,0.313 10 false j8 2.708,2.24 3.865,2.771 1.156,0.531 10 false Navigation ECU 2.458,1.76 3.073,2.146 0.615,0.385 10 false n2 3.802,1.76 4.219,2.135 0.417,0.375 10 false j6 2.458,0.844 2.938,1.25 0.479,0.406 10 false n2 3.792,1.313 4.208,1.688 0.417,0.375 10 false j6 3.802,0.865 4.219,1.24 0.417,0.375 10 false j6 1.479,0.99 2.635,1.521 1.156,0.531 10 false ECU-B NO. 2 0.5,0.813 1.365,1.354 0.865,0.542 10 false from Battery 2.792,0.813 3.281,1.208 0.49,0.396 10 false +B 2.802,1.75 3.292,2.146 0.49,0.396 10 false GND 3.24,0.865 3.729,1.26 0.49,0.396 10 false US4+ 3.26,1.302 3.75,1.698 0.49,0.396 10 false US4- 3.219,1.76 3.708,2.156 0.49,0.396 10 false UGD4 5.885,0.885 6.375,1.281 0.49,0.396 10 false US4+ 5.896,1.323 6.385,1.719 0.49,0.396 10 false US4- 5.896,1.781 6.385,2.177 0.49,0.396 10 false UGD4 3.813,0.667 4.229,1.042 0.417,0.375 10 false 4 3.813,1.125 4.229,1.5 0.417,0.375 10 false 5 3.813,1.573 4.229,1.948 0.417,0.375 10 false 6 2.448,0.635 2.865,1.01 0.417,0.375 10 false 10 2.458,1.563 2.875,1.938 0.417,0.375 10 false 23 5.656,0.76 6.073,1.135 0.417,0.375 10 false 1 5.646,1.177 6.063,1.521 0.417,0.344 10 false 2 5.656,1.667 6.073,2.01 0.417,0.344 10 false 3 1.156,3.344 2.906,3.635 1.75,0.292 10 false : USB Communication Line 5.74,3.354 6.5,3.583 0.76,0.229 10 false *: Shielded 4.875,1.677 5.104,1.844 0.229,0.167 10 false * 0.156,0.146 1.854,0.583 1.698,0.438 12 false for TMMT Made:

E425815E01
5.729,2.438 6.917,3.24 1.188,0.802 10 false Radio and Display Receiver Assembly 5.74,2.219 6.188,2.531 0.448,0.313 10 false j8 2.708,2.24 3.865,2.771 1.156,0.531 10 false Navigation ECU 2.375,1.76 2.99,2.146 0.615,0.385 10 false F168 3.802,1.76 4.219,2.135 0.417,0.375 10 false k3 2.365,0.844 2.844,1.25 0.479,0.406 10 false F168 3.781,1.313 4.198,1.688 0.417,0.375 10 false k3 3.802,0.865 4.219,1.24 0.417,0.375 10 false k3 1.479,0.99 2.635,1.521 1.156,0.531 10 false ECU-B NO. 2 0.51,0.813 1.385,1.479 0.875,0.667 10 false from Battery 2.792,0.813 3.281,1.208 0.49,0.396 10 false +B 2.802,1.75 3.292,2.146 0.49,0.396 10 false GND 3.24,0.865 3.729,1.26 0.49,0.396 10 false US4+ 3.26,1.302 3.75,1.698 0.49,0.396 10 false US4- 3.219,1.76 3.708,2.156 0.49,0.396 10 false UGD4 5.885,0.885 6.375,1.281 0.49,0.396 10 false US4+ 5.896,1.323 6.385,1.719 0.49,0.396 10 false US4- 5.896,1.781 6.385,2.177 0.49,0.396 10 false UGD4 3.813,0.667 4.229,1.042 0.417,0.375 10 false 4 3.813,1.125 4.229,1.5 0.417,0.375 10 false 5 3.813,1.573 4.229,1.948 0.417,0.375 10 false 6 2.448,0.635 2.865,1.01 0.417,0.375 10 false 10 2.458,1.563 2.875,1.938 0.417,0.375 10 false 23 5.656,0.76 6.073,1.135 0.417,0.375 10 false 1 5.646,1.177 6.063,1.521 0.417,0.344 10 false 2 5.656,1.667 6.073,2.01 0.417,0.344 10 false 3 1.156,3.344 2.906,3.635 1.75,0.292 10 false : USB Communication Line 5.74,3.354 6.5,3.583 0.76,0.229 10 false *: Shielded 4.875,1.677 5.104,1.844 0.229,0.167 10 false * 0.146,0.146 1.844,0.583 1.698,0.438 12 false for TMC Made: 4.135,2.26 5.542,3.042 1.406,0.781 10 false No. 1 Navigation Wire

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK MAP SCREEN
a.

Turn the ignition switch ACC and wait for 90 seconds.


b.

Press the "MAP" switch and check that the map screen is displayed normally.


Result:
Result Proceed to
Map screen is displayed normally A
Map screen is not displayed normally B


HINT:
·

This DTC may be stored due to environmental reasons such as electrical noise or interference.

·

Clear past DTCs when the map screen is displayed normally. (Codes stored due to past environmental factors)




A

B

2.CHECK DTC
2.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the ignition switch off.


c.

Turn the ignition switch ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Result Proceed to
OK A
NG (for TMMT Made) B
NG (for TMC Made) C



A

B

3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)

C

7.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)
a.
E364286C66
1.5,0.333 1.917,0.583 0.417,0.25 2.573,1.323 2.99,0.906 true 2.427,1.51 2.563,1.906 true 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 1.615,0.365 2.073,0.563 0.458,0.198 10 false n2 2.469,1.948 2.896,2.167 0.427,0.219 10 false GND 3.063,0.76 3.302,0.938 0.24,0.177 10 false +B
*a Front view of wire harness connector
(to Navigation ECU)


Disconnect the n2 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
n2-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
n2-10 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - NAVIGATION ECU)
a.
E368007C51
1.49,0.5 1.906,0.75 0.417,0.25 1.479,2.667 1.896,2.917 0.417,0.25 1.813,1.313 2.396,1.01 true 1.625,1.344 1.094,0.969 true 1.677,1.458 1.438,2.021 true 2.406,3.115 2.031,3.417 true 1.104,3.021 1.917,3.448 true 1.719,3.969 1.927,3.583 true 0.271,0.146 0.583,0.302 0.313,0.156 10 false *a 0.323,2.448 0.635,2.604 0.313,0.156 10 false *b 1.635,0.521 2.063,0.74 0.427,0.219 10 false j8 1.604,2.708 2.167,2.979 0.563,0.271 10 false j6 2.479,0.896 3.052,1.125 0.573,0.229 10 false US4- 0.729,0.823 1.302,1.052 0.573,0.229 10 false US4+ 1.208,2.073 1.781,2.302 0.573,0.229 10 false UGD4 1.49,4.031 2.063,4.26 0.573,0.229 10 false UGD4 0.708,2.885 1.281,3.115 0.573,0.229 10 false US4+ 2.458,2.958 3.031,3.188 0.573,0.229 10 false US4-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the j6 navigation ECU connector.


b.

Disconnect the j8 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
j6-4 (US4+) - j8-1 (US4+) Always Below 1 Ω
j6-5 (US4-) - j8-2 (US4-) Always Below 1 Ω
j6-6 (UGD4) - j8-3 (UGD4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.REPLACE NAVIGATION ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC
6.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the Ignition switch off.


c.

Turn the ignition switch ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG

7.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU - BATTERY AND BODY GROUND)
a.
E364286C67
1.5,0.333 1.917,0.583 0.417,0.25 2.573,1.323 2.99,0.906 true 2.427,1.51 2.563,1.906 true 0.198,0.146 0.51,0.344 0.313,0.198 10 false *a 1.552,0.385 2.01,0.583 0.458,0.198 10 false F168 2.469,1.948 2.896,2.167 0.427,0.219 10 false GND 3.063,0.76 3.302,0.938 0.24,0.177 10 false +B
*a Front view of wire harness connector
(to Navigation ECU)


Disconnect the F168 navigation ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F168-23 (GND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F168-10 (+B) - Body ground Ignition switch off 11 to 14 V



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 1 NAVIGATION WIRE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT NO. 1 NAVIGATION WIRE
a.
E368007C52
1.49,0.5 1.906,0.75 0.417,0.25 1.479,2.667 1.896,2.917 0.417,0.25 1.813,1.313 2.396,1.01 true 1.625,1.344 1.094,0.969 true 1.677,1.458 1.438,2.021 true 2.406,3.115 2.031,3.417 true 1.104,3.021 1.917,3.448 true 1.719,3.969 1.927,3.583 true 0.271,0.146 0.583,0.302 0.313,0.156 10 false *a 0.323,2.448 0.635,2.604 0.313,0.156 10 false *b 1.635,0.521 2.063,0.74 0.427,0.219 10 false j8 1.604,2.708 2.167,2.979 0.563,0.271 10 false k3 2.479,0.896 3.052,1.125 0.573,0.229 10 false US4- 0.729,0.823 1.302,1.052 0.573,0.229 10 false US4+ 1.208,2.073 1.781,2.302 0.573,0.229 10 false UGD4 1.49,4.031 2.063,4.26 0.573,0.229 10 false UGD4 0.708,2.885 1.281,3.115 0.573,0.229 10 false US4+ 2.458,2.958 3.031,3.188 0.573,0.229 10 false US4-
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)
*b Front view of wire harness connector
(to Navigation ECU)


Disconnect the k3 navigation ECU connector.


b.

Disconnect the j8 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
k3-4 (US4+) - j8-1 (US4+) Always Below 1 Ω
k3-5 (US4-) - j8-2 (US4-) Always Below 1 Ω
k3-6 (UGD4) - j8-3 (UGD4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

9.REPLACE NAVIGATION ECU

NG

REPLACE NAVIGATION

9.REPLACE NAVIGATION ECU
a.

Replace the navigation ECU with a new or known good one.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

10.CHECK DTC
10.CHECK DTC
a.

Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs
50002 212

b.

Turn the Ignition switch off.


c.

Turn the ignition switch ON and wait for 90 seconds.


d.

Recheck for DTCs and check that no DTCs are output.

Body Electrical > Navigation System > Trouble Codes
50001 212
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

END (NAVIGATION ECU IS DEFECTIVE)

NG