Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060815 NAVIGATION / MULTI INFO DISPLAY _0299845 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Microphone Circuit  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

E381473E23
0.333,2.438 0.75,2.667 0.417,0.229 10 false R2 0.333,2.594 2.313,3.208 1.979,0.615 10 false Map Light Assembly (Telephone Microphone Assembly) 5.427,2.927 5.844,3.156 0.417,0.229 10 false F131 5.406,3.104 7.094,3.719 1.688,0.615 10 false Radio and Display Receiver Assembly 5.948,2.625 6.427,2.854 0.479,0.229 10 false SGND 5.958,1.583 6.375,1.813 0.417,0.229 10 false MIN+ 5.958,1.052 6.49,1.281 0.531,0.229 10 false MACC 5.958,0.531 6.375,0.76 0.417,0.229 10 false SNS2 5.677,0.438 6.094,0.667 0.417,0.229 10 false 25 5.677,0.969 6.094,1.198 0.417,0.229 10 false 23 5.688,1.49 6.104,1.719 0.417,0.229 10 false 21 5.677,2 6.094,2.229 0.417,0.229 10 false 22 5.677,2.521 6.094,2.75 0.417,0.229 10 false 24 1.677,1.99 2.094,2.219 0.417,0.229 10 false 7 1.677,1.458 2.094,1.688 0.417,0.229 10 false 8 1.677,0.927 2.094,1.156 0.417,0.229 10 false 9 1.677,0.427 2.094,0.656 0.417,0.229 10 false 1 1.135,1.583 1.635,1.792 0.5,0.208 10 false MCO+ 1.146,2.104 1.646,2.313 0.5,0.208 10 false MCO- 1.125,1.042 1.656,1.271 0.531,0.229 10 false MACC 5.979,2.094 6.396,2.323 0.417,0.229 10 false MIN- 1.156,0.521 1.573,0.75 0.417,0.229 10 false SNS2 3.438,2.354 4.25,2.688 0.813,0.333 10 false (Shielded)

PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E277821

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-23 (MACC) - R2-9 (MACC) Always Below 1 Ω
F131-21 (MIN+) - R2-8 (MCO+) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-23 (MACC) - Body ground Always 10 kΩ or higher
F131-21 (MIN+) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher
F131-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.
E366062C58
1.427,0.198 1.917,0.479 0.49,0.281 2.01,1.354 2.844,1.646 true 2.5,1.802 1.906,1.365 true 1.979,1.885 1.802,1.375 true 1.521,0.24 1.896,0.438 0.375,0.198 10 false F131 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 2.813,1.656 3.271,1.854 0.458,0.198 10 false MIN- 1.885,1.917 2.385,2.146 0.5,0.229 10 false SGND 2.354,1.823 2.979,2.021 0.625,0.198 10 false MACC
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F131-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-24 (SGND) - Body ground Always Below 1 Ω
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

NG

4.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Remove the map light assembly (telephone microphone assembly).

for TMC Made: Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMC Made)>REMOVAL

for TMMT Made: Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL


b.
E358190C06
2.281,1.094 2.552,0.49 true 2.292,1.427 2.583,1.771 true 0.25,0.198 0.563,0.396 0.313,0.198 10 false *a 2.479,0.302 2.948,0.521 0.469,0.219 10 false SNS2 2.583,1.771 3.219,1.958 0.635,0.188 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Result Proceed to
OK A
NG (for TMC Made) B
NG (for TMMT Made) C



A

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

C

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

5.INSPECT MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)
a.

Reconnect the F131 radio and display receiver assembly connector.


b.

Reconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Turn the ignition switch to ACC.


d.
E358189C03
1.542,0.49 1.969,0.75 0.427,0.26 2.188,1.75 2.708,2.177 true 1.99,1.781 2.208,2.385 true 0.219,0.177 0.531,0.375 0.313,0.198 10 false *a 1.646,0.521 1.958,0.719 0.313,0.198 10 false R2 2.76,2.188 3.198,2.458 0.438,0.271 10 false MCO- 2.115,2.427 2.604,2.698 0.49,0.271 10 false MCO+
*a Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.


e.

Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.

Result:
Result Proceed to
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. A
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. (for TMC Made) B
A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. (for TMMT Made) C




A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)

C

REPLACE MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)