Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › 2019.09–2021.09
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P223711  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground  P223712  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery  P223713  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open  P223716  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold  P223717  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold  P22371B  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold  P225111  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground  P225112  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery  


DESCRIPTION

Refer to DTC P003012.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P003012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P223711 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground for Rear air fuel ratio sensor type

The A1A+ voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

The A1A+ voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2238
P223712 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery for Rear air fuel ratio sensor type

The A1A+ voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

The A1A+ voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).


·

Short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2239
P223713 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open An open or ground short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor (sensor 1) while the engine is running (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2237
P223716 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold for Rear air fuel ratio sensor type

Difference between terminals A1A+ and A1A- is 0.1 V or less for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

Difference between terminals A1A+ and A1A- is 0.1 V or less for 5 seconds or more (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2238
P223717 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold for Rear air fuel ratio sensor type

Difference between terminals A1A+ and A1A- is higher than 0.8 V for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

Difference between terminals A1A+ and A1A- is 0.8 V or higher for 5 seconds or more (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2239
P22371B A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Resistance Above Threshold The air fuel ratio sensor (sensor 1) admittance is higher than 0.0054 1/Ω (2 trip detection logic).
·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2238
P225111 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground for Rear air fuel ratio sensor type

The A1A- voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

The A1A- voltage is 0.5 V or less for 5 seconds or more (2 trip detection logic).


·

Open or short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2252
P225112 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery for Rear air fuel ratio sensor type

The A1A- voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).


for Rear heated oxygen sensor type

The A1A- voltage is higher than 4.5 V for 5 seconds or more (2 trip detection logic).


·

Short in air fuel ratio sensor (sensor 1) circuit

·

Air fuel ratio sensor (sensor 1)

·

ECM


Comes on DTC stored SAE Code:
P2253

MONITOR DESCRIPTION

These DTCs are output when there is an open or short in the air fuel ratio sensor (sensor 1) circuit, or if the air fuel ratio sensor (sensor 1) output drops. To detect these problems, the voltage of the air fuel ratio sensor (sensor 1) monitored when turning the ignition switch to ON, and the admittance (admittance is an electrical term that indicates the ease of flow of current) is checked while driving. If the voltage of the air fuel ratio sensor (sensor 1) is between 0.5 V and 4.5 V, it is considered normal. If the voltage is out of the specified range, or the admittance is less than the standard value, the ECM determines that there is a malfunction in the air fuel ratio sensor (sensor 1). If the same malfunction is detected in the next driving cycle, the ECM will illuminate the MIL and store a DTC.

MONITOR STRATEGY

Required Sensors/Components Air fuel ratio sensor (sensor 1)
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait 5 minutes.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P223711, P223712, p223713, P223716, P223717, P22371B, P225111 or P225112.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, idle the engine for 5 minutes and check the DTC judgment result again.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Refer to "Data List / Active Test" [A/F (O2) Sensor Voltage B1S1].

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for Rear air fuel ratio sensor type A
for Rear heated oxygen sensor type B



A

2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR (SENSOR 1) VOLTAGE)

B

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
2.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR (SENSOR 1) VOLTAGE)
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.
A395477C04
0.667,2.083 1.167,2.333 0.5,0.25 1.125,2.813 1.604,2.354 true 2.344,2.813 1.917,2.333 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 0.813,2.125 1.125,2.323 0.313,0.198 10 false C25 0.958,2.833 1.458,3.063 0.5,0.229 10 false A1A+ 2.25,2.833 2.75,3.063 0.5,0.229 10 false A1A-
*a Front view of wire harness connector
(to Air Fuel Raito Sensor (Sensor 1))


Disconnect the air fuel ratio sensor (sensor 1) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C25-3 (A1A+) - Body ground Ignition switch ON 2.8 to 3.0 V
C25-4 (A1A-) - Body ground Ignition switch ON 2.3 to 2.7 V
C25-3 (A1A+) - C25-4 (A1A-) Ignition switch ON 0.1 to 0.7 V



HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Result:
Proceed to
OK
NG



OK

REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
a.

Disconnect the C25 air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C62-19 (HA1A) Always Below 1 Ω
C25-3 (A1A+) - C62-131 (A1A+) Always Below 1 Ω
C25-4 (A1A-) - C62-132 (A1A-) Always Below 1 Ω
C25-1 (HA1A) or C62-19 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (A1A+) or C62-131 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (A1A-) or C62-132 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR (SENSOR 1) - ECM)
a.

Disconnect the C25 air fuel ratio sensor (sensor 1) connector.


b.

Disconnect the C62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C25-1 (HA1A) - C62-19 (HA1A) Always Below 1 Ω
C25-3 (A1A+) - C62-131 (A1A+) Always Below 1 Ω
C25-4 (A1A-) - C62-132 (A1A-) Always Below 1 Ω
C25-1 (HA1A) or C62-19 (HA1A) - Body ground and other terminals Always 10 kΩ or higher
C25-3 (A1A+) or C62-131 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C25-4 (A1A-) or C62-132 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE AIR FUEL RATIO SENSOR (SENSOR 1)
a.

Replace the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "Inspection After Repair" after replacing the air fuel ratio sensor (sensor 1).

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P223711, P223712, P223713, P223716, P223717, P22371B, P225111 OR P225112)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P223711, P223712, P223713, P223716, P223717, P22371B, P225111 OR P225112)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

j.

Input the DTC: P223711, P223712, P223713, P223716, P223717, P22371B, P225111 or P225112.


k.

Check the DTC judgment result.

Result:
Result Proceed to
NORMAL
(DTCs are not output)
A
ABNORMAL
(DTC P223711, P223712, P223713, P223716, P223717, P22371B, P225111 or P225112 is output)
B




A

END

B