The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System (for Radio and Display Type)).
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
2. DRAIN ENGINE COOLANT
3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55737B
4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
55734D
5.REMOVE WATER GUARD PLATE LH
55736D
6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55735C
7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH
55701J
8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY
87246
9.DISCONNECT OUTLET HEATER WATER HOSE
Slide the hose clip to disconnect the outlet heater water hose.
To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.
Do not apply excessive force to the outlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87245
10.DISCONNECT INLET HEATER WATER HOSE
Slide the hose clip to disconnect the inlet heater water hose.
To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.
Do not apply excessive force to the inlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
88707
11.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt and rotate the hook connector as shown in the illustration.
Disconnect the suction pipe sub-assembly.
Remove the O-ring from the suction pipe subassembly.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
88716A
12.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
Disconnect the cooler refrigerant liquid pipe A.
Remove the O-ring from the cooler refrigerant liquid pipe A.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
13.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
14.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)
Use the same procedure as for the LH side.
15.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
16.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)
Use the same procedure as for the LH side.
55401E
17.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
18.REMOVE STEERING COLUMN ASSEMBLY
85940
19.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY
89340A
20.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)
82878
21.REMOVE ECU INTEGRATION BOX LH
88625Q
22.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Disconnect the connector and air conditioning duct sub-assembly to remove the cooler thermistor (room temperature sensor).
55215D
23.REMOVE NO. 3 DASH PANEL INSULATOR PAD
Remove the 2 front floor carpet clips.
|
Remove in this Direction |
Remove the clip.
Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.
Disengage the clips to remove the No. 3 dash panel insulator pad.
55307C
24.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Remove the 2 nuts and separate the relay block assembly.
Remove the bolt to disconnect the ground wire.
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No.2 instrument panel brace sub-assembly.
55306A
25.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
55308B
26.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Disengage the claws and clamp.
Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
82141
27.DISCONNECT INSTRUMENT PANEL WIRE
Disconnect each connector.
| *a | Clamp | *b | Hook |
Remove the bolt and screw.
Remove the 4 bolts to disconnect the 4 ground wires.
Remove the 2 nuts A.
Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.
Disengage clamps and hook to disconnect the instrument panel wire.
88539J
28.DISCONNECT DRAIN COOLER HOSE
| *1 | Cooler Unit Drain Hose Grommet |
Disconnect the drain cooler hose.
If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.
29.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Remove the 2 bolts.
Remove the 5 bolts.
Remove the nut.
Disengage the clamps.
Disconnect the 2 connectors.
Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
|
Remove in this Direction | - | - |
30.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.
55990B
31.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Disengage the claws to remove the lower defroster nozzle assembly.