Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL TANK (for 2WD) › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293900 FUEL TANK(for 2WD) A

8NR-FTS FUEL  FUEL TANK(for 2WD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Gas leak from exhaust system is repaired Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

Because the weight of the fuel tank sub-assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the components could fall down.

·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 2.DRAIN FUEL

Hide 17430 3.REMOVE TAIL EXHAUST PIPE ASSEMBLY

Hide 57628C 4.REMOVE REAR FLOOR SIDE MEMBER COVER LH (w/ Cover)

a.
A393592N01
0.552,1.813 0.708,2.01 0.156,0.198 10 true A 2,0.156 2.156,0.354 0.156,0.198 10 true B

Remove the 3 bolts and clip (A).


b.

Disengage the clip (B) to remove the rear floor side member cover LH.


Hide 57627A 5.REMOVE REAR FLOOR SIDE MEMBER COVER RH (w/ Cover)

a.
A393591

Remove the 3 bolts.


b.

Disengage the clip to remove the rear floor side member cover RH.


Hide 77641A 6.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A393593

Remove the nut, 4 clips and No. 1 fuel tank protector from the fuel tank assembly.


Hide 77754B 7.DISCONNECT CHARCOAL CANISTER OUTLET HOSE

a.
A393792

Slide the hose clip and disconnect the charcoal canister outlet hose from the fuel tank filler pipe sub-assembly.


Hide 8.DISCONNECT FUEL TANK BREATHER TUBE

a.
A393793

Disconnect the fuel tank breather tube from the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77213E 9.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A393794

Loosen the clamp, then disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77026A 10.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A397744

Disconnect the No. 1 fuel evaporation tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77209F 11.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A395522

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>8NR-FTS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77100 12.REMOVE FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.
A393597

Support the fuel tank assembly using an engine lifter.

HINT:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.
A393598

Remove the 4 bolts and No. 1 fuel tank band sub-assemblies.


c.

Lower the engine lifter to remove the fuel tank assembly.

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When removing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




Hide 77651A 13.REMOVE NO. 1 FUEL TANK CUSHION

a.
A393599

Remove the 2 No. 1 fuel tank cushions from the fuel tank assembly.


Hide 77026A 14.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A393789

Disengage the 4 clamps to remove the No. 1 fuel evaporation tube sub-assembly from the fuel tank assembly.


Hide 77209F 15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A393790

Disengage the 3 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.


Hide 77754B 16.REMOVE CHARCOAL CANISTER OUTLET HOSE

a.
A393791

Disengage the 2 clamps to remove the charcoal canister outlet hose from the fuel tank assembly.