The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Audio and Visual System).
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) battery terminal (for Navigation System (for Radio and Display Type)).
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))
2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))
3. DRAIN ENGINE COOLANT (for 8NR-FTS)
4. DRAIN ENGINE COOLANT (for 3ZR-FAE)
5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
55737B
6.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
55736D
7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH
55735C
8.REMOVE COWL BODY MOUNTING REINFORCEMENT RH
55701J
9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)
55701J
10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)
87246
11.DISCONNECT OUTLET HEATER WATER HOSE
Slide the hose clip to disconnect the outlet heater water hose.
To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.
Do not apply excessive force to the outlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
87245
12.DISCONNECT INLET HEATER WATER HOSE
Slide the hose clip to disconnect the inlet heater water hose.
To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.
Do not apply excessive force to the inlet heater water hose.
Prepare a drain pan or cloth in case the coolant leaks.
88707
13.DISCONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the bolt.
Disconnect the suction pipe sub-assembly and cooler refrigerant liquid pipe A shown in the illustration.
Remove the 2 O-rings from the suction pipe sub-assembly and cooler refrigerant liquid pipe A.
Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.
14.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)
15.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)
Use the same procedure as for the LH side.
16.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)
17.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)
Use the same procedure as for the LH side.
55401E
18.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
19.REMOVE STEERING COLUMN ASSEMBLY
85940
20.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY
89340A
21.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)
82877
22.REMOVE ECU INTEGRATION BOX RH (for LHD)
82878
23.REMOVE ECU INTEGRATION BOX LH (for RHD)
88625Q
24.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Disconnect the connector and air conditioning duct sub-assembly to remove the cooler thermistor (room temperature sensor).
55215D
25.REMOVE NO. 3 DASH PANEL INSULATOR PAD
Remove the 2 front floor carpet clips.
|
Remove in this Direction |
Remove the clip.
Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.
Disengage the clips to remove the No. 3 dash panel insulator pad.
87212K
26.REMOVE REAR NO. 6 AIR DUCT (w/ Rear Air Duct)
|
Remove in this Direction |
Disengage the claws to remove the rear No. 6 air duct as shown in the illustration.
87212J
27.REMOVE REAR NO. 5 AIR DUCT (w/ Rear Air Duct)
|
Remove in this Direction |
Disengage the claws to remove the rear No. 5 air duct as shown in the illustration.
87212H
28.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)
Remove the 2 front floor carpet clips.
|
Remove in this Direction |
Remove the clip.
Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.
|
Remove in this Direction |
Disengage the claws to remove the rear No. 4 air duct as shown in the illustration.
87212G
29.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Air Duct)
|
Remove in this Direction |
Disengage the claws to remove the rear No. 3 air duct as shown in the illustration.
87212F
30.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)
|
Remove in this Direction |
Disengage the claws to remove the rear No. 2 air duct.
87212
31.REMOVE REAR NO. 1 AIR DUCT (w/ Rear Air Duct)
|
Remove in this Direction |
Disengage the claws to remove the rear No. 1 air duct as shown in the illustration.
55306A
32.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
w/ PTC Heater:
Remove the bolt to disconnect the ground wire.
Remove the 2 nuts and separate the relay block assembly.
for LHD:
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
for RHD:
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.
55307C
33.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
for LHD:
Remove the bolt to disconnect the ground wire.
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.
for RHD:
Remove the bolt to disconnect the ground wire.
Disengage the clamps to disconnect the wire harness.
Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.
55308B
34.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Disengage the clamp and claws.
Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.
88539J
35.REMOVE DRAIN COOLER HOSE
| *1 | Cooler Unit Drain Hose Grommet |
Disconnect the drain cooler hose.
If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.
82141
36.DISCONNECT INSTRUMENT PANEL WIRE
for LHD:
Disconnect each connector.
| *a | Clamp | *b | Hook |
Remove the bolt and screw.
Remove the 4 bolts to disconnect the 4 ground wires.
Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.
Disengage clamps and hook to disconnect the instrument panel wire.
for RHD:
Disconnect each connector.
| *a | Clamp | *b | Hook |
Remove the bolt and screw.
Remove the 4 bolts to disconnect the 4 ground wires.
Remove the 2 nuts A.
Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.
Disengage clamps and hook to disconnect the instrument panel wire.
37.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.
Remove the 2 bolts.
Remove the 5 bolts.
Remove the nut.
Disengage the clamps.
Disconnect 2 connectors.
Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
|
Remove in this Direction | - | - |
38.REMOVE AIR CONDITIONER UNIT ASSEMBLY
Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.
55990B
39.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY
Disengage the claws to remove the lower defroster nozzle assembly.