Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Wear protective gloves. Sharp areas on the parts may injure your hands.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the driver side and front passenger side.
The procedure listed below is for the driver side.
72443B
1.INSTALL VERTICAL ADJUSTER GEAR (w/ Vertical Adjuster)
Install the vertical adjuster gear.
Install the front vertical adjuster brake sub-assembly.
Make sure to insert the stud bolt of the front vertical adjuster brake sub-assembly into the hole of the front seat adjuster assembly as shown in the illustration.
Install the vertical adjuster spacer.
Install the vertical adjuster plate with the 3 nuts.
Tighten the nuts in the order shown in the illustration.
72125A
2.INSTALL REAR UPPER SEAT TRACK COVER
Use the same procedure for both sides.
|
Install in this Direction |
Engage the claws to install the rear upper seat track cover as shown in the illustration.
72266
3.INSTALL SEAT TRACK UPPER RAIL COVER
Use the same procedure for both sides.
|
Install in this Direction |
Engage the claws to install the seat track upper rail cover as shown in the illustration.
82821A
4.INSTALL CONNECTOR COVER (w/o Seat Heater System)
Engage the claw to install the connector cover.
82667B
5.INSTALL CONNECTOR HOLDER (for Front Passenger Side)
Engage the claw to install the connector holder.
72211C
6.INSTALL SEAT TRACK ADJUSTING HANDLE
Engage the claws to install the seat track adjusting handle to the front seat adjuster assembly.
71052A
7.INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY
Engage the hooks to install the front seat cushion spring sub-assembly to the front seat adjuster assembly.
7181B
8.INSTALL FRONT SEAT CUSHION WIRE HARNESS HOLDER
Engage the claw to install the front seat cushion wire harness holder.
Install the 2 screws.
82192
9.INSTALL FRONT SEAT WIRE (for Driver Side)
Engage the claw.
Disengage the clamps to install the front seat wire.
82191
10.INSTALL FRONT SEAT WIRE (for Front Passenger Side)
Engage the claw.
Disengage the clamps to install the front seat wire.
8219A
11.INSTALL NO. 2 FRONT SEAT WIRE (w/ Seat Position Airbag Sensor)
Engage the claw and clamp to install the No. 2 front seat wire.
71875G
12.INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/ Vertical Adjuster)
Engage the claws to install the reclining adjuster inside cover RH.
71876G
13.INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/ Vertical Adjuster)
Engage the claws to install the reclining adjuster inside cover LH.
w/ Lumbar Support:
Engage the claw.
71875F
14.INSTALL RECLINING ADJUSTER INSIDE COVER RH (w/o Vertical Adjuster)
Engage the claws to install the reclining adjuster inside cover LH.
71876F
15.INSTALL RECLINING ADJUSTER INSIDE COVER LH (w/o Vertical Adjuster)
Engage the claws to install the RH seat reclining adjuster inside cover LH.
71873A
16.INSTALL FRONT SEAT LOWER CUSHION SHIELD (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield.
71874A
17.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)
| *a | Hook |
| *b | Guide |
Engage the claw and guide.
Engage the hook to install the front seat lower cushion shield LH.
87510L
18.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)
71072S
19.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
When installing a separate type front seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
Engage the claws to install the separate type front seat cushion cover to the separate type front seat cushion pad.
Be careful not to damage the separate type front seat cushion cover.
20.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage the hooks (A) and hooks (B) to install the separate type front seat cushion cover with pad.
Engage the hooks.
for Front Passenger Side:
Engage the claw to install the occupant detection sensor connector.
w/ Seat Heater System:
Connect the connector.
Engage the clamp.
8219B
21.INSTALL NO. 2 FRONT SEAT WIRE (w/ Lumbar Support)
Engage the clamp to install the No. 2 front seat wire.
71759B
22.INSTALL FRONT SEATBACK HOOK
Engage the claws to install the 2 front seatback hooks from the front seatback frame sub-assembly.
71054S
23.INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY (w/o Lumbar Support)
Install the 2 front seatback edge protectors to the front seatback spring sub-assembly.
|
Install in this Direction |
Engage the guides to install the front seatback spring sub-assembly to the front seatback frame sub-assembly as shown in the illustration.
Engage the claws to install the 2 front seatback edge protectors to the front seatback frame sub-assembly.
79977A
24.INSTALL SEATBACK FELT (w/ Lumbar Support)
72760D
25.INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY (w/ Lumbar Support)
73920A
26.INSTALL FRONT SEAT AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)
87510N
27.INSTALL FRONT SEATBACK HEATER ASSEMBLY (w/ Seat Heater System)
71074S
28.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
When installing a separate type front seatback cover, refer to Precaution in order to prevent wrinkles from forming.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>PRECAUTION
w/ Front Seat Airbag Assembly:
Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to damage the separate type front seatback cover.
w/o Front Seat Airbag Assembly:
Engage the claws to install the separate type front seatback cover to the separate type front seatback pad.
Be careful not to damage the separate type front seatback cover.
29.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
71931
30.INSTALL FRONT SEAT HEADREST SUPPORT
|
Install in this Direction |
Engage the claws to install the 2 front seat headrest supports as shown in the illustration.
Close the 2 fasteners as shown in the illustration.
w/ Seat Heater System:
Engage the clamp.
Engage the hooks.
31.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
Engage the guides to install the separate type front seatback assembly to the separate type front seat cushion assembly.
Install the 4 bolts.
w/ Front Seat Side Airbag
Engage the claw and clamps to install the front seat airbag assembly wire harness.
Engage the claw first.
w/ Seat Heater System:
Engage the clamp.
Connect the connector.
w/ Lumbar Support:
Engage the clamp.
Connect the connector.
Engage the hooks.
Engage the hook.
72498A
32.INSTALL VERTICAL ADJUSTER BRACKET COVER (w/ Vertical Adjuster)
Engage the claw to install the vertical adjuster bracket cover.
71862
33.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Driver Side)
|
Install in this Direction |
Engage the claws and guides as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat inner cushion shield as shown in the illustration.
84922A
34.INSTALL FRONT LUMBAR POWER SEAT SWITCH (w/ Lumbar Support)
71812D
35.INSTALL FRONT SEAT CUSHION SHIELD (for Driver Side)
w/ Lumbar Support:
Connect the connector.
Engage the clamps.
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat cushion shield as shown in the illustration.
71861
36.INSTALL FRONT SEAT INNER CUSHION SHIELD (for Front Passenger Side)
|
Install in this Direction |
Engage the claws and guides as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat inner cushion shield as shown in the illustration.
71811D
37.INSTALL FRONT SEAT CUSHION SHIELD (for Front Passenger Side)
w/ Vertical Adjuster:
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) as shown in the illustration.
w/o Vertical Adjuster:
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guide (A) as shown in the illustration.
Engage the claws and guides (B) as shown in the illustration.
|
Install in this Direction |
Engage the claws to install the front seat cushion shield as shown in the illustration.
71849F
38.INSTALL SEAT ADJUSTER COVER CAP (w/ Vertical Adjuster)
|
Install in this Direction (1) |
|
Install in this Direction (2) |
Engage the guides as shown in the illustration.
Engage the claws to install the seat adjuster cover cap as shown in the illustration.
72526A
39.INSTALL RECLINING ADJUSTER RELEASE HANDLE
Engage the guide to install the reclining adjuster release handle.
72538
40.INSTALL RECLINING HINGE OUTER COVER
|
Install in this Direction |
Engage the guide and claw to install the reclining hinge outer cover as shown in the illustration.
72495
41.INSTALL VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)
|
Install in this Direction |
Engage the claw to install the vertical adjusting handle as shown in the illustration.
71074S
42.CONNECT SEPARATE TYPE FRONT SEATBACK COVER
Connect the rubber band of the separate type front seatback cover.
73240
43.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
44.INSTALL FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
87501B
45.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)
89178A
46.INSTALL SEAT POSITION AIRBAG SENSOR (w/ Seat Position Airbag Sensor)
72277A
47.INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (w/ Seat Position Airbag Sensor)