Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B1579  Voice Recognition Microphone Disconnected  


DESCRIPTION

The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1579 Voice Recognition Microphone Disconnected Telephone microphone signal is lost.
·

Map light assembly (telephone microphone assembly)

·

Radio and display receiver assembly

·

Harness or connector



WIRING DIAGRAM

for TMMT Made
E360100E02
4.906,2.188 6.594,2.76 1.688,0.573 10 false Radio and Display Receiver Assembly 4.927,2.01 5.542,2.208 0.615,0.198 10 false F131 5.083,1.542 5.698,1.74 0.615,0.198 10 false MIN- 5.073,0.708 5.688,0.906 0.615,0.198 10 false SNS2 4.813,1.385 5.125,1.583 0.313,0.198 10 false 22 4.833,0.594 5.146,0.792 0.313,0.198 10 false 25 2.146,0.583 2.458,0.781 0.313,0.198 10 false 1 2.167,1.375 2.479,1.573 0.313,0.198 10 false 7 1.646,1.479 2.365,1.719 0.719,0.24 10 false MCO- 1.677,0.698 2.396,0.938 0.719,0.24 10 false SNS2 0.865,2.156 2.865,2.76 2,0.604 10 false Map Light Assembly (Telephone Microphone Assembly) 0.875,2 1.49,2.198 0.615,0.198 10 false R2

for TMC Made
E431708E01
4.938,1.802 6.625,2.375 1.688,0.573 10 false Radio and Display Receiver Assembly 4.938,1.615 5.552,1.813 0.615,0.198 10 false F131 5.094,1 5.708,1.198 0.615,0.198 10 false MIN- 5.073,0.563 5.688,0.76 0.615,0.198 10 false SNS2 4.833,0.917 5.146,1.115 0.313,0.198 10 false 22 4.833,0.438 5.146,0.635 0.313,0.198 10 false 25 2.552,0.458 2.865,0.656 0.313,0.198 10 false 1 2.552,0.906 2.865,1.104 0.313,0.198 10 false 7 2.063,0.906 2.781,1.146 0.719,0.24 10 false MCO- 2.01,0.427 2.729,0.667 0.719,0.24 10 false SNS2 0.396,2.292 2.146,2.521 1.75,0.229 10 false Map Light Assembly 0.427,2.125 1.042,2.323 0.615,0.198 10 false R2 0.406,1.573 2.792,2.094 2.385,0.521 10 false Telephone Microphone Assembly 0.417,1.406 0.729,1.604 0.313,0.198 10 false B 1.448,0.448 1.76,0.646 0.313,0.198 10 false 1 1.458,0.896 1.771,1.094 0.313,0.198 10 false 2

PROCEDURE

1.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E360498C62
1.531,0.729 1.948,0.99 0.417,0.26 2.813,2.604 2.052,2.156 true 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.583,0.781 2.51,1.052 0.927,0.271 10 false F131 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CONFIRM MODEL

NG

2.CONFIRM MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
for TMMT Made A
for TMC Made B




A

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))

B

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly (telephone microphone assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly (telephone microphone assembly).


b.
E265420C11
1.042,1.615 1.365,1.125 true 2.594,1.646 2.208,1.146 true 0.188,0.208 0.5,0.406 0.313,0.198 10 false *a 2.51,1.688 2.979,1.896 0.469,0.208 10 false SNS2 0.771,1.656 1.24,1.865 0.469,0.208 10 false MCO-
*a Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

5.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the R2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-25 (SNS2) - R2-1 (SNS2) Always Below 1 Ω
F131-22 (MIN-) - R2-7 (MCO-) Always Below 1 Ω
F131-25 (SNS2) - Body ground Always 10 kΩ or higher
F131-22 (MIN-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT MAP LIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT MAP LIGHT ASSEMBLY
a.

b.
E431698C01
1.51,1.792 1.906,2.052 0.396,0.26 1.458,0.188 1.854,0.448 0.396,0.26 2.104,1.229 2.667,1.115 true 2.521,0.594 2.083,1 true 1.552,0.229 2.01,0.427 0.458,0.198 10 false R2 1.635,1.844 2.094,2.042 0.458,0.198 10 false B 2.594,0.469 3.208,0.667 0.615,0.198 10 false SNS2 2.719,1.021 3.333,1.219 0.615,0.198 10 false MCO- 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 0.156,1.792 0.469,1.99 0.313,0.198 10 false *b
*a Component without harness connected
(Map Light Assembly)
*b Component without harness connected
(Telephone Microphone Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R2-1 (SNS2) - B-1 Always Below 1 Ω
R2-7 (MCO-) - B-2 Always Below 1 Ω
R2-1 (SNS2) - R2-7 (MCO-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG