Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2019.09
RM32H0E _56 Audio / Visual / Telematics _060227 AUDIO / VIDEO _0295690 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Mute Signal Circuit between Radio Receiver and Telematics Transceiver  


DESCRIPTION

The telematics transceiver sends a mute signal to the radio and display receiver assembly.

The radio and display receiver assembly controls the volume according to the mute signal from the telematics transceiver.

WIRING DIAGRAM

E426530E01
1.271,1.031 1.885,1.229 0.615,0.198 10 false TMUT 1.75,0.917 2.365,1.115 0.615,0.198 10 false 3 5.292,0.917 5.906,1.115 0.615,0.198 10 false 17 5.531,1.021 6.146,1.219 0.615,0.198 10 false MUTE 0.688,1.917 1.302,2.115 0.615,0.198 10 false F131 0.677,2.083 1.885,2.573 1.208,0.49 10 false Radio and Display Receiver Assembly 5.115,2.063 7.031,2.354 1.917,0.292 10 false Telematics Transceiver 5.115,1.896 5.729,2.094 0.615,0.198 10 false F51

CAUTION / NOTICE / HINT

NOTICE:

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION


PROCEDURE

1.INSPECT TELEMATICS TRANSCEIVER
a.
E259127C52
1.469,0.531 1.906,0.802 0.438,0.271 1.385,1.927 1.021,0.958 true 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.563,0.573 1.896,0.771 0.333,0.198 10 false F51 0.563,0.854 1.063,1.063 0.5,0.208 10 false MUTE
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F51-17 (MUTE) - Body ground Ignition switch ACC
Audio system playing
→ Emergency call mode
2.0 V or higher
→ Below 1 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the F131 radio and display receiver assembly connector.


b.

Disconnect the F51 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F131-3 (TMUT) - F51-17 (MUTE) Always Below 1 Ω
F131-3 (TMUT) or F51-17 (MUTE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the telematics transceiver connector.


b.
E176650C46
1.479,0.719 1.969,1.01 0.49,0.292 1.99,2.083 2.167,2.583 true 0.188,0.167 0.354,0.323 0.167,0.156 10 false *a 2.031,2.635 2.458,2.792 0.427,0.156 10 false MUTE 1.604,0.771 1.948,0.969 0.344,0.198 10 false F51
*a Front view of wire harness connector
(to Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
F51-17 (MUTE) - Body ground Ignition switch ACC 2.0 V or higher



Result:
Proceed to
OK
NG



OK

NG