The radio and display receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the map light assembly (telephone microphone assembly), and the map light assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.
Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.
When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
NG
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for TMMT Made | A |
| for TMC Made | B |
A
B
Disconnect the F131 radio and display receiver assembly connector.
Disconnect the R2 map light assembly (telephone microphone assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-25 (SNS2) - R2-1 (SNS2) | Always | Below 1 Ω |
| F131-23 (MACC) - R2-9 (MACC) | Always | Below 1 Ω |
| F131-21 (MIN+) - R2-8 (MCO+) | Always | Below 1 Ω |
| F131-22 (MIN-) - R2-7 (MCO-) | Always | Below 1 Ω |
| F131-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F131-23 (MACC) - Body ground | Always | 10 kΩ or higher |
| F131-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| F131-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| F131-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F131 radio and display receiver assembly connector.
Reconnect the R2 map light assembly (telephone microphone assembly) connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-24 (SGND) - Body ground | Always | Below 1 Ω |
| F131-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Remove the map light assembly (telephone microphone assembly).
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMMT Made)>REMOVAL
| *a | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F131 radio and display receiver assembly connector.
Reconnect the R2 map light assembly (telephone microphone assembly) connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly (Telephone Microphone Assembly)) |
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly (telephone microphone assembly) connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is output. | A |
| A waveform synchronized with the voice input to the map light assembly (telephone microphone assembly) is not output. | B |
A
B
Disconnect the F131 radio and display receiver assembly connector.
Disconnect the R2 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-25 (SNS2) - R2-1 (SNS2) | Always | Below 1 Ω |
| F131-23 (MACC) - R2-9 (MACC) | Always | Below 1 Ω |
| F131-21 (MIN+) - R2-8 (MCO+) | Always | Below 1 Ω |
| F131-22 (MIN-) - R2-7 (MCO-) | Always | Below 1 Ω |
| F131-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| F131-23 (MACC) - Body ground | Always | 10 kΩ or higher |
| F131-21 (MIN+) - Body ground | Always | 10 kΩ or higher |
| F131-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| F131-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F131 radio and display receiver assembly connector.
Reconnect the R2 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F131-24 (SGND) - Body ground | Always | Below 1 Ω |
| F131-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMC Made)>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (SNS2) - 7 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for TMC Made)>REMOVAL
Remove the telephone microphone assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>MICROPHONE>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R2-9 (MACC) - B-5 | Always | Below 1 Ω |
| R2-7 (MCO-) - B-2 | Always | Below 1 Ω |
| R2-1 (SNS2) - B-1 | Always | Below 1 Ω |
| R2-8 (MCO+) - B-3 | Always | Below 1 Ω |
| R2-9 (MACC) or B-5 - Body ground | Always | 10 kΩ or higher |
| R2-7 (MCO-) or B-2 - Body ground | Always | 10 kΩ or higher |
| R2-8 (MCO+) or B-3 - Body ground | Always | 10 kΩ or higher |
| R2-7 (MCO-) or B-3 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the F131 radio and display receiver assembly connector.
Reconnect the R2 map light assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly) |
Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the R2 map light assembly connector.
Check the waveform of the map light assembly (telephone microphone assembly) using the oscilloscope.
| Result | Proceed to |
|---|---|
| A waveform synchronized with the voice input to the map light assembly is output. | A |
| A waveform synchronized with the voice input to the map light assembly is not output. | B |
A
B