Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2019.09
RM32H0E _58 Vehicle Interior _060136 METER / GAUGE / DISPLAY _0294876 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Speedometer Malfunction  


DESCRIPTION

The combination meter assembly receives vehicle speed signals from the brake actuator assembly (skid control ECU) via CAN communication. The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly (skid control ECU). The brake actuator assembly (skid control ECU) supplies power to the vehicle speed sensor. The brake actuator assembly (skid control ECU) detects vehicle speed signals based on pulses of the voltage.

HINT:
·

Factors that affect the indicated vehicle speed include the tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using the GTS. For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

·

If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly (skid control ECU) stores DTCs. Troubleshoot the vehicle stability control system.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



WIRING DIAGRAM

E341411E01
0.073,3.104 1.677,3.604 1.604,0.5 10 false Brake Actuator Assembly (Skid Control ECU) 2.948,3.188 4.844,3.385 1.896,0.198 10 false : CAN Communication Line 5.281,3.104 7.135,3.427 1.854,0.323 10 false Combination Meter Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:

Before starting the following inspection, check tire size and tire air pressure.


PROCEDURE

1.CHECK FOR DTC (METER / GAUGE SYSTEM)

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

2.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

B

2.CHECK FOR DTC (VEHICLE STABILITY CONTROL SYSTEM)

Result:
Result Proceed to
DTCs are not output. A
DTCs are output. B



A

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

3.PERFORM ACTIVE TEST USING GTS (SPEED METER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Combination Meter > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Speed Meter Operation Speedometer OFF, 0, 40, 80, 120, 160, 200, 240, 280 There is a deviation in the values displayed on the speedometer (Control range → Speedometer display)
(1) for Gauge speedometer (except Australia) Reference km/h:
·

40 → 41.7 to 46.2

·

80 → 83.4 to 88.4

·

120 → 125.1 to 130.6

·

160 → 166.2 to 173.2

·

200 → 207.7 to 215.7


(2) for Gauge speedometer (for Australia) Reference km/h:
·

40 → 41.2 to 44.8

·

80 → 82.4 to 86.0

·

120 → 123.6 to 127.4

·

160 → 164.9 to 168.9

·

200 → 206.3 to 209.9


(3) for Gauge speedometer Reference mph:
·

40 → 42.0 to 44.5

·

80 → 83.1 to 87.1

·

120 → 124.7 to 129.6


Body Electrical > Combination Meter > Active Test
Tester Display
Speed Meter Operation
50004 122 1
OK:

Speedometer indication is normal.



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPLACE COMBINATION METER ASSEMBLY