Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294193 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Heater)

NOTICE:

If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value such as DTC B1801, C1231 and C1433 will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


a.
B459845C01
1.75,0.375 2.25,0.167 true 0.5,0.667 1.188,1.156 true 0.292,0.51 0.604,0.708 0.313,0.198 10 false *a 2.344,0.052 2.656,0.25 0.313,0.198 10 false (A)
*a Flat Cable


Check if the spiral cable sub-assembly is centered.

HINT:

When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



b.

If the spiral cable sub-assembly is not centered, center it.

i.
B459846C01
1.729,1.688 1.729,1.271 true 1.667,1.708 1.844,1.896 0.177,0.188 10 true *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.




ii.
B459847C01
0.615,0.646 1.198,1.146 true 1.719,1.26 1.719,1.844 true 1.104,1.406 1.083,1.833 1.083,1.833 1.01,1.5 true 0.417,0.521 0.729,0.719 0.313,0.198 10 false *a 1.01,1.896 1.323,2.094 0.313,0.198 10 false *c 1.656,1.896 1.885,2.063 0.229,0.167 10 true *b
*a Flat Cable
*b Interlock
*c Alignment Mark


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the alignment marks are aligned and the flat cable shown in the illustration is visible.

HINT:

The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.




Hide 84306 2.INSPECT SPIRAL CABLE SUB-ASSEMBLY (w/ Steering Heater)

NOTICE:

If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value such as DTC B1801, C1231 and C1433 will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.


a.
B459859C01
1.781,0.344 2.25,0.146 true 2.115,1.396 2.719,1.094 true 2.333,0.031 2.552,0.229 0.219,0.198 10 false (A) 2.75,0.948 2.906,1.146 0.156,0.198 10 false *a
*a Flat Cable


Check if the spiral cable sub-assembly is centered.

HINT:

When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



b.

If the spiral cable sub-assembly is not centered, center it.

i.
B459860C01
1.74,1.854 1.719,1.25 true 1.667,1.917 1.906,2.115 0.24,0.198 10 true *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.




ii.
B459861C01
2.094,1.385 2.823,0.792 true 2.24,1.396 2.125,1.802 2.125,1.802 2.354,1.5 true 1.75,1.26 1.688,1.833 true 2.854,0.646 3.083,0.854 0.229,0.208 10 false *a 2,1.813 2.229,2.021 0.229,0.208 10 true *c 1.594,1.885 1.823,2.094 0.229,0.208 10 true *b
*a Flat Cable
*b Interlock
*c Alignment Mark


While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the alignment marks are aligned and the flat cable shown in the illustration is visible.

HINT:

The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.




Hide 84306 3.INSTALL SPIRAL CABLE SUB-ASSEMBLY

a.
B279789C06
2.25,0.615 1.938,0.49 true 2.313,0.771 1.979,1.063 1.979,1.063 2.344,1.156 true 2.917,0.854 3.156,0.635 true 0.51,0.917 0.302,0.594 true 1.781,0.406 2.094,0.563 0.313,0.156 10 false *c 1.823,1 2.135,1.156 0.313,0.156 10 false *a 3.177,0.552 3.406,0.698 0.229,0.146 10 false *b 0.146,0.5 0.375,0.646 0.229,0.146 10 false *b
*a Guide
*b Pin
*c Lock Pin


Align the pins and guides, and engage the claws to install the spiral cable sub-assembly to the steering sensor.

NOTICE:
·

Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.

·

Do not damage the pins of the spiral cable sub-assembly or guides of the steering sensor.

·

The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.




b.
C238437

Remove the lock pin from the steering sensor.


Hide 84307 4.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the front wheels are aligned facing straight ahead.


d.
B459844

Engage the claws to install the spiral cable with sensor sub-assembly.


e.

Connect each connector.


Hide 45286B 5.INSTALL UPPER STEERING COLUMN COVER

Hide 45287 6.INSTALL LOWER STEERING COLUMN COVER

Hide 7. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84307 8.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/o Steering Heater)

NOTICE:

Do not adjust the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.


a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B459843C02
1.771,0.698 2.083,0.417 true 0.917,0.833 1.417,1.125 true 0.656,0.729 0.854,0.896 0.198,0.167 10 true *a 2.167,0.25 2.427,0.448 0.26,0.198 10 true (A)
*a Flat Cable


Check if the spiral cable with sensor sub-assembly is centered.

HINT:

When the spiral cable with sensor sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



d.

If the spiral cable with sensor sub-assembly is not centered, center it.

i.
B459848C01
1.708,1.594 1.708,1.177 true 1.646,1.635 1.833,1.833 0.188,0.198 10 true *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.




ii.
B459849C01
1.75,0.688 2.167,0.333 true 0.75,1 1.417,1.115 true 1.719,1.604 1.719,1.188 true 2.281,0.188 2.5,0.385 0.219,0.198 10 true (A) 0.469,0.875 0.698,1.083 0.229,0.208 10 true *b 1.635,1.688 1.865,1.896 0.229,0.208 10 true *a
*a Interlock
*b Flat Cable


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to the position where the part (A) is positioned at the top and the flat cable shown in the illustration is visible.

HINT:

The spiral cable with sensor sub-assembly can be rotated approximately 2.5 times to both the left and right from the center.




Hide 84307 9.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ Steering Heater)

NOTICE:

Do not adjust the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.


a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.
B459857C02
1.76,0.708 2.25,0.49 true 1.938,1.26 2.542,1 true 2.292,0.354 2.531,0.573 0.24,0.219 10 true (A) 2.583,0.865 2.74,1.063 0.156,0.198 10 true *a
*a Flat Cable


Check if the spiral cable with sensor sub-assembly is centered.

HINT:

When the spiral cable with sensor sub-assembly is centered, the part (A) is positioned at the top and the flat cable shown in the illustration is visible.



d.

If the spiral cable with sensor sub-assembly is not centered, center it.

i.
B459862C01
1.74,1.802 1.74,1.198 true 1.635,1.833 1.865,2.063 0.229,0.229 10 true *a
*a Interlock


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:
·

When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.

·

Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.




ii.
B459863C01
1.729,1.875 1.708,1.208 true 2.531,0.854 1.917,1.271 true 1.667,0.708 0.979,0.49 true 0.719,0.313 0.938,0.51 0.219,0.198 10 true (A) 2.563,0.698 2.781,0.917 0.219,0.219 10 true *b 1.635,1.906 1.854,2.125 0.219,0.219 10 true *a
*a Interlock
*b Flat Cable


While pushing on the interlock shown in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 times to the position where the part (A) is positioned at the top and the flat cable shown in the illustration is visible.

HINT:

The spiral cable with sensor sub-assembly can be rotated approximately 2.5 times to both the left and right from the center.




Hide 45100 10.INSTALL STEERING WHEEL ASSEMBLY

Hide 11.PERFORM CALIBRATION

·

Simple intelligent parking assist system (w/ Simple Intelligent Parking Assist System):

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION

·

Parking support brake system (w/ Parking Support Brake System):

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>CALIBRATION

·

Panoramic view monitor system (w/ Panoramic View Monitor System):

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PANORAMIC VIEW MONITOR SYSTEM>CALIBRATION