Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › REAR CRANKSHAFT OIL SEAL › from 2019.09
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0291516 REAR CRANKSHAFT OIL SEAL A

8NR-FTS ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free from foreign matter.



b.
A351487C02
2.198,0.969 2.76,0.885 true 0.708,0.438 1.021,0.594 0.313,0.156 10 true *a 2.844,0.802 3.302,1 0.458,0.198 10 false SST
*a Tap in Depth


Using SST and a hammer, tap in the rear engine oil seal.

SST
09223-15030  
09950-70010  (09951-07100)

Rear Engine Oil Seal Tap in Depth:

- 0.9 to 0.9 mm (- 0.0354 to 0.0354 in.)



Hide 32101B 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

a.
A351484N01
1.958,1.646 2.135,0.333 2.135,0.333 0.438,0.427 true 1.635,1.656 2.125,0.333 false 2.219,0.271 2.677,0.469 0.458,0.198 10 false SST

Using SST, hold the crankshaft pulley assembly.

SST
09213-70011  (09213-70020)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A351488C02
1.073,1.667 1.292,1.667 false 2.104,1.552 2.323,1.552 false 1.729,2.448 1.948,2.448 false 0.885,1.604 1.198,1.76 0.313,0.156 10 false *1 2.365,1.49 2.677,1.646 0.313,0.156 10 false *2 2.01,2.396 2.323,2.552 0.313,0.156 10 false *3
*1 Front Drive Plate Spacer (Reversible)
*2 Rear Drive Plate Spacer
*3 Drive Plate and Ring Gear Sub-assembly
V100135

Engine Side
V100136

Transaxle Side


Install the front drive plate spacer.

HINT:

Align the pin of the front drive plate spacer with the pin hole of the crankshaft.



d.

Install the drive plate and ring gear sub-assembly and rear drive plate spacer to the crankshaft.


e.
A192239C18
1.563,0.75 1.667,0.75 1.667,0.75 1.813,1.229 false 1.385,0.677 1.583,0.833 0.198,0.156 10 *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.
A351485N01
1.635,0.5 1.792,0.698 0.156,0.198 10 true 1 2.063,1.667 2.219,1.865 0.156,0.198 10 true 2 1.271,1.26 1.427,1.458 0.156,0.198 10 true 3 2.427,1.021 2.583,1.219 0.156,0.198 10 true 4 1.271,0.896 1.427,1.094 0.156,0.198 10 true 5 2.354,1.375 2.51,1.573 0.156,0.198 10 true 6 2.26,0.563 2.417,0.76 0.156,0.198 10 true 7 1.458,1.646 1.615,1.844 0.156,0.198 10 true 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.



Hide 13405 3.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

a.

Using SST, hold the crankshaft pulley assembly.

SST
09213-70011  (09213-70020)
09330-00021  


b.

Clean the 8 bolts and 8 bolt holes.


c.
A192239C18
1.563,0.75 1.667,0.75 1.667,0.75 1.813,1.229 false 1.385,0.677 1.583,0.833 0.198,0.156 10 *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 8 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
A357245N01
2.135,0.615 2.292,0.813 0.156,0.198 10 true 4 1.115,1.625 1.271,1.823 0.156,0.198 10 true 3 2.24,1.104 2.396,1.302 0.156,0.198 10 true 6 0.969,1.125 1.125,1.323 0.156,0.198 10 true 5 2.063,1.594 2.219,1.792 0.156,0.198 10 true 2 1.146,0.625 1.302,0.823 0.156,0.198 10 true 1 1.615,1.76 1.771,1.958 0.156,0.198 10 true 7 1.677,0.438 1.833,0.635 0.156,0.198 10 true 8

Install and uniformly tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the flywheel sub-assembly.



e.
A238927C01
2.208,1.26 2.365,1.26 false 1.969,0.573 2.208,0.719 0.24,0.146 10 false 90°
V100155

Paint Mark


Mark each bolt head with paint as shown in the illustration.


f.

Tighten the 8 bolts by 90° in the same order.


g.

Check that the paint marks are now at a 90° angle.


h.

Check that the crankshaft turns smoothly.


Hide 31250 5.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)