Home › Drivetrain › K313F (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2019.09–2020.08
RM32H0E _52 Drivetrain _059618 K313F MULTIDRIVE / CVT _0292475 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K313F MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  INSTALLATION  


PROCEDURE

Hide 35012B 1.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.

Apply Toyota Genuine CVT fluid FE to a new O-ring, and install it to the No. 2 breather plug (CVT).

NOTICE:

Be careful not to damage or twist the O-ring.



b.

Install the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) to the breather plug hose.


c.

Install the transmission breather hose sub-assembly to the continuously variable transaxle assembly.


Hide 2.INSTALL STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.

Install the straight screw plug and a new gasket to the continuously variable transaxle assembly.

Torque:
16.2 N*m (165 kgf*cm, 12 ft.*lbf)


Hide 87101A 3.INSTALL NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.

Install the No. 1 heater bracket sub-assembly to the continuously variable transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


b.

Install the clamp to the No. 1 heater bracket sub-assembly.


c.

Install the No. 1 breather plug (CVT) to the clamp.


Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C364048

Install the 4 wire harness clamp brackets to the continuously variable transaxle assembly with the 4 bolts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


Hide 30400E 5.INSTALL CVT OIL PUMP TYPE T OIL SEAL

a.

Ensure that there is no dirt or foreign matter on your hands and then apply MP grease to the entire periphery of the lip of a new CVT oil pump type T oil seal.


b.

Temporarily install the CVT oil pump type T oil seal by pressing it to the installation surface of the oil pump housing by hand.

NOTICE:

Be sure to install the CVT oil pump type T oil seal in the correct direction.



c.

Clean the CVT oil pump type T oil seal contact surface of SST and the area around it.

SST
09309-36010  


d.
C329653C01
1.677,2.49 1.677,2.115 false 0.833,2.771 1.146,2.927 0.313,0.156 10 false *a 1.573,2.521 2.031,2.719 0.458,0.198 10 false SST
*a Depth


Using SST and a hammer, drive the CVT oil pump type T oil seal in evenly, until it is even with the side surface of the oil pump housing.

Standard Depth:

0 to 0.5 mm (0 to 0.0197 in.)


NOTICE:
·

Drive the CVT oil pump type T oil seal in gradually, while visually checking that it is even.

·

After installation, confirm that the CVT oil pump type T oil seal has been driven in until it is even with the side surface of the oil pump housing.

·

Wipe any extra grease off with your hand.




Hide 36100A 6.INSTALL TRANSFER AND TRANSAXLE SETTING STUD BOLT

Hide 32000A 8.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C327733C02
1.313,1.531 1.49,1.531 true 0.458,1.531 0.646,1.531 true 2.417,1.667 2.583,1.167 false 0.75,2.167 0.958,1.875 true 1.042,1.219 1.167,0.938 true 2.656,1.063 2.906,1.25 0.25,0.188 10 false *a 1.24,0.802 1.438,0.969 0.198,0.167 10 true *b 0.281,1.469 0.469,1.635 0.188,0.167 10 true *c 1.51,1.469 1.698,1.635 0.188,0.167 10 true *c 0.521,2.125 0.698,2.302 0.177,0.177 10 true *b
*a Matchmark
*b Wide Groove
*c Narrow Groove


Turn the front oil pump drive gear so that the groove is at the top and place a matchmark on the transaxle housing to indicate the position of the groove.

NOTICE:
·

Place the matchmark on the transaxle housing to indicate the position of the wide groove.

·

The matchmark position must be correct to prevent damage.




b.
C267518C03
1.448,1.813 1.698,1.625 true 1.698,0.281 2.01,0.125 false 2.042,0.042 2.24,0.208 0.198,0.167 10 false *a 1.271,1.76 1.479,1.948 0.208,0.188 10 false *b
*a Key
*b Matchmark


Place a matchmark on the torque converter assembly so that the position of its key is clearly indicated.


c.
C327735C02
1.177,0.75 0.573,0.26 0.573,0.26 1.167,0.583 true 2.542,1.281 1.844,1.938 1.844,1.938 2.542,0.99 true 1.677,1.885 1.906,2.063 0.229,0.177 10 false *1 0.396,0.177 0.635,0.365 0.24,0.188 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Align the matchmark on the transaxle housing with the one on the torque converter assembly and engage the splines of the input shaft with the turbine runner splines.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




d.
C327736C02
2.542,1.271 1.844,1.958 1.844,1.958 2.542,0.979 true 0.917,0.25 1.177,0.583 false 1.167,1.563 0.833,2 true 1.677,1.906 1.906,2.104 0.229,0.198 10 false *1 0.698,0.115 0.979,0.333 0.281,0.219 10 false *a 0.615,1.938 0.833,2.115 0.219,0.177 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° and engage the splines of the stator shaft with the stator assembly.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not damage the CVT oil pump type T oil seal.




e.
C327737C02
1.177,0.76 0.688,0.219 0.688,0.219 1.177,0.583 true 2.542,1.281 1.823,1.969 1.823,1.969 2.542,0.99 true 1.656,1.917 1.885,2.104 0.229,0.188 10 false *1 0.51,0.125 0.813,0.323 0.302,0.198 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Matchmark


Rotate the torque converter assembly approximately 180° again, align the matchmark on the torque converter assembly with the one on the transaxle housing and insert the key of the torque converter assembly into the groove of the front oil pump drive gear.

NOTICE:
·

Install the torque converter assembly to the input shaft while keeping it horizontal.

·

Do not push the torque converter assembly excessively when rotating it.

·

Do not damage the CVT oil pump type T oil seal.




f.

Clean the drive plate and torque converter assembly setting bolt holes.


g.
C327738C02
0.583,2.75 0.927,2.24 true 1.073,1.021 0.833,0.51 true 2.417,1 2.583,0.75 false 2.573,1.802 2.74,1.552 false 0.635,0.396 0.854,0.594 0.219,0.198 10 false *a 0.375,2.771 0.615,2.958 0.24,0.188 10 false *b 2.198,0.979 2.417,1.177 0.219,0.198 10 false *a 2.365,1.792 2.604,1.979 0.24,0.188 10 false *b 2.24,0.229 2.396,0.427 0.156,0.198 10 false A
*a Engine Assembly Surface
*b Drive Plate Surface


Using a vernier caliper and straightedge, measure the dimension (A) between the continuously variable transaxle assembly contact surface of the engine*a and the torque converter assembly contact surfaces of the drive plate*b.


h.
C327739N02
2.625,0.479 2.792,0.667 0.167,0.188 10 false B

Using a vernier caliper and straightedge, measure the dimension (B) shown in the illustration and check that the dimension (B) is more than the dimension (A), which was measured in the previous step.

Standard:

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the continuously variable transaxle assembly is installed to the engine assembly with the torque converter assembly not sufficiently inserted, the torque converter assembly may be damaged.

·

Do not include the thickness of the set block.




Hide 30400 9.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.

Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 30400 10.INSTALL CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C327740C02
1.625,0.896 2.479,0.313 true 0.792,1.031 1.031,1.229 0.24,0.198 10 false *1 2.573,0.208 2.823,0.406 0.25,0.198 10 false *2
*1 Crankshaft
*2 Torque Converter Assembly Centerpiece
V100135

Clutch Spline Grease


Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter assembly centerpiece.

Clutch Spline Grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum Grease Amount:

Approximately 1 g (0.0353 oz.)



b.
C327741C02
0.542,0.667 1.5,0.667 true 2.479,1.177 2.75,1.667 true 0.313,0.563 0.521,0.75 0.208,0.188 10 false *1 2.75,1.719 2.958,1.906 0.208,0.188 10 false *1 1.01,2.354 1.167,2.552 0.156,0.198 10 false A 2.385,2.365 2.542,2.563 0.156,0.198 10 false A 2.448,4.365 2.615,4.573 0.167,0.208 10 false B 1.958,4.5 2.135,4.667 0.177,0.167 10 false B 1.573,4.469 1.729,4.646 0.156,0.177 10 false B 0.917,4.115 1.063,4.292 0.146,0.177 10 true B 0.677,3.271 0.823,3.469 0.146,0.198 10 true B
*1 Knock Pin


Confirm that the 2 knock pins are installed to the engine assembly and are not damaged.


c.

Install the continuously variable transaxle assembly to the engine assembly with the 7 bolts.

Torque:
29.5 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not use excess force when installing the continuously variable transaxle assembly.

·

When mounting the continuously variable transaxle assembly to the engine assembly, make sure to securely fit the knock pins into the knock holes.

·

Check that the torque converter assembly rotates.

·

When tightening the bolts, be sure that the mating surfaces of the engine assembly and the continuously variable transaxle assembly are in close contact with one another.



HINT:
·

Bolt (A): Install from continuously variable transaxle assembly side

·

Bolt (B): Install from engine assembly side




Hide 12325A 11.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C364046C02
0.583,1.167 1.146,1.333 0.563,0.167 10 true 1 (*a), 4 2.75,1.333 2.906,1.531 0.156,0.198 10 true 3 1.844,0.469 2,0.667 0.156,0.198 10 true 2
*a Temporarily Tighten


Install the transverse engine engine mounting bracket to the continuously variable transaxle assembly with the 3 bolts in the order shown in the illustration.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 12.INSTALL ENGINE MOUNTING STAY LH

a.
C364045C02
0.26,0.917 0.917,1.083 0.656,0.167 10 true 1 (*a), 3 2.01,0.885 2.167,1.083 0.156,0.198 10 true 2
*a Temporarily Tighten


Install the engine mounting stay LH to the continuously variable transaxle assembly and transverse engine engine mounting bracket with the 2 bolts in the order shown in the illustration.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 12372A 13.INSTALL TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.
C364044C01
0.333,0.75 0.917,0.917 0.583,0.167 10 true 1 (*a), 5 0.75,1.052 0.906,1.25 0.156,0.198 10 true 3 1.917,1.802 2.073,2 0.156,0.198 10 true 2 2.677,1.167 2.833,1.365 0.156,0.198 10 true 4 2.521,0.146 2.677,0.344 0.156,0.198 10 true 6
*a Temporarily Tighten


Temporarily install the transverse engine engine mounting insulator to the vehicle body with the nut and 4 bolts.


b.

Fully tighten the nut and 4 bolts in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
C364043

Install the transverse engine engine mounting insulator to the transverse engine engine mounting bracket with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

Turn the bolt while holding the nut.



Hide 32101G 14.INSTALL DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.

Clean the threads of the 6 drive plate and torque converter assembly setting bolts.


b.
C321585C03
1.865,1.688 1.865,1.427 false 1.813,1.719 2.125,1.875 0.313,0.156 10 false *a
*a Adhesive


Apply a few drops of adhesive to 2 or 3 threads at the tip of each of the 6 drive plate and torque converter assembly setting bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter assembly setting bolts and install each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

NOTICE:

First install the black colored drive plate and torque converter assembly setting bolt, and then the remaining 5 silver colored drive plate and torque converter assembly setting bolts.



Hide 11361J 15.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing under cover to the stiffening crankcase assembly.


Hide 11363A 16.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 28100 17.INSTALL STARTER ASSEMBLY (for Valeo Made Cold Area Specification Vehicles)

Hide 28100 18.INSTALL STARTER ASSEMBLY (for Valeo Made except Cold Area Specification Vehicles)

Hide 28100 19.INSTALL STARTER ASSEMBLY (for Denso Made without Stop and Start System)

Hide 12364B 20.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C364047C02
2.417,0.563 3.021,0.76 0.604,0.198 10 true 1 (*a), 5 1.229,1.115 1.385,1.323 0.156,0.208 10 true 3 1.615,1.375 1.771,1.573 0.156,0.198 10 true 2 2,1.323 2.156,1.521 0.156,0.198 10 true 4
*a Temporarily Tighten


Install the No. 2 engine moving control rod to the continuously variable transaxle assembly with the 4 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 21.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 51108A 22.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 23.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 24.REMOVE ENGINE SUPPORT BRIDGE

a.

Remove SST from the vehicle body.

NOTICE:

Prevent SST from contacting the vehicle body or windshield glass.



b.

Install the neck from the windshield washer jar assembly with the clip.


Hide 25.REMOVE ENGINE HANGER

a.

Remove the 2 bolts and No. 2 engine hanger from the cylinder head.


b.

Remove the 2 bolts and No. 1 engine hanger from the cylinder head.


c.

Connect the No. 2 earth wire to the engine mounting insulator sub-assembly RH with the bolt.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


d.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


e.

Install the engine wire to the wire harness clamp bracket with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Engage the 3 clamps with the wire harness clamp bracket.


Hide 37100 26.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 27.INSTALL FRONT DRIVE SHAFT ASSEMBLIES (for TMC Made)

Hide 28.INSTALL FRONT DRIVE SHAFT ASSEMBLIES (for TMMT Made)

Hide 17410 29.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 17420K 30.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

Hide 45025D 32.INSTALL NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 33.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45260 34.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 35.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 33823 36.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the No. 1 transmission control cable bracket to the continuously variable transaxle assembly with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 37.CONNECT WATER HOSE

a.

Engage the 2 clamps to install the water hose to the continuously variable transaxle assembly.


b.

Connect the water hose to the transmission oil cooler and slide the 2 hose clips to secure them.


Hide 82121 38.CONNECT ENGINE WIRE

a.

Engage the 7 clamps to connect the engine wire to the continuously variable transaxle assembly.

C364040C04
2.25,0.833 2.563,1.031 0.313,0.198 10 true *1 2.021,1.667 2.333,1.865 0.313,0.198 10 true *2 2.271,2.333 2.583,2.531 0.313,0.198 10 true *3 4.417,0.5 4.729,0.698 0.313,0.198 10 true *4 4.833,2.219 5.146,2.417 0.313,0.198 10 true *5
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Oil Pressure Sensor Connector - -



b.

Connect the oil pressure sensor connector.


c.

Connect the transmission revolution sensor (NOUT) connector.


d.

Connect the park/neutral position switch connector.


e.

Connect the transmission revolution sensor (NIN) connector.


f.

Connect the transmission wire connector.


g.

Connect the engine wire to the continuously variable transaxle assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 33820B 39.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

Hide 74404A 40.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the air battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


b.

Engage the clamp to connect the engine wire to the battery clamp sub-assembly.


c.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


Hide 17701 42.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 43.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 44.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 45.INSTALL RADIATOR COVER

Hide 55701J 46.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 47.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 48.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 49.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 50.INSTALL WATER GUARD PLATE LH (for TMC Made RHD)

Hide 55737B 51.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 52.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 53.INSTALL FRONT WHEELS

Hide 28800 54.INSTALL BATTERY

Hide 55.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>8NR-FTS BATTERY>INSTALLATION

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 57.ADD COOLANT (for Intercooler)

Hide 58.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 61.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK

Hide 62.INSPECT FOR EXHAUST GAS LEAK

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for AWD)>INSTALLATION

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


Hide 51443C 65.INSTALL REAR ENGINE UNDER COVER RH

Hide 51444A 66.INSTALL REAR ENGINE UNDER COVER LH

Hide 51441 67.INSTALL NO. 1 ENGINE UNDER COVER

Hide 71.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT