for Continuously Variable Transaxle:
The skid control ECU (brake actuator assembly) receives shift position information from the ECM via CAN communication.
In addition, front seat inner belt information and driver seat door courtesy switch information is received from the main body ECU (multiplex network body ECU).
The electric parking brake system AUTO function (shift-linked function) automatically releases the parking brake when the following conditions are met: 1) Ignition switch to ON, 2) brake pedal is depressed, and 3) shift lever is moved out of P. When the shift lever is moved to P with these conditions met, the function automatically locks the parking brake.
The electric parking brake system AUTO (shift-linked function) automatically engages the parking brake when the shift lever is moved to P and disengages the parking brake when the shift lever is moved out of P when the ignition switch to ON and the brake pedal is depressed.
for Manual Transaxle:
The skid control ECU (brake actuator assembly) receives clutch stroke information from the ECM via CAN communication.
In addition, front seat inner belt information and driver seat door courtesy switch information is received from the main body ECU (multiplex network body ECU).
The AUTO function (ignition switch-linked function) of the electric parking brake system automatically locks when the ignition switch is turned off.
The electric parking brake may still operate up to 20 seconds after the ignition switch is turned off. Before disconnecting connectors or fuses, turn the ignition switch off and wait 20 seconds or more.
When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light blinks (red) when the ignition switch is first turned to ON.
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Auto Mode | AUTO mode permission status | ON or OFF | OFF: Manual mode
ON: AUTO mode |
- |
| Tester Display |
|---|
| Auto Mode |
When switching the mode, check that the Data List display turns on and off.
| Result | Proceed to |
|---|---|
| The Data List display does not turn on and off according to mode switching | A |
| The Data List display turns on and off according to mode switching (for CVT) | B |
| The Data List display turns on and off according to mode switching (for Manual Transaxle) | C |
A
B
C
Inspect the electric parking brake switch (electric parking brake switch assembly).
Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the F67 electric parking brake switch (electric parking brake switch assembly) connector.
Disconnect the A42 skid control ECU (brake actuator assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A42-31 (SWI1) - F67-6 (SWI1) | Always | Below 5 Ω |
| A42-32 (SWO1) - F67-5 (SWO1) | Always | Below 5 Ω |
| A42-15 (SWI2) - F67-4 (SWI2) | Always | Below 5 Ω |
| A42-16 (SWO2) - F67-3 (SWO2) | Always | Below 5 Ω |
| A42-31 (SWI1) or F67-6 (SWI1) - Body ground | Always | 10 kΩ or higher |
| A42-32 (SWO1) or F67-5 (SWO1) - Body ground | Always | 10 kΩ or higher |
| A42-15 (SWI2) or F67-4 (SWI2) - Body ground | Always | 10 kΩ or higher |
| A42-16 (SWO2) or F67-3 (SWO2) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for CVT) | A |
| OK (for Manual Transaxle) | B |
| NG | C |
A
B
C
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Shift Position | Shift lever position information | "P,N", R, D/M, 1st-6th/B or Fail | Actual shift lever position | for Continuously Variable Transaxle |
On the GTS screen, ON or OFF is displayed accordingly.
| Tester Display |
|---|
| Shift Lever Position |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for K114) | B |
| NG (for K313) | C |
| NG (for K313F) | D |
A
B
C
D
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light SW | Stop light switch | OFF or ON | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Tester Display |
|---|
| Stop Light SW |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Accelerator Position Sensor No.1 Voltage and Accelerator Position Sensor No.2 Voltage.
| Tester Display |
|---|
| Accelerator Position Sensor No.1 Voltage |
| Accelerator Position Sensor No.2 Voltage |
Read the values displayed on the GTS.
| Accelerator Pedal Operation | Accelerator Position Sensor No.1 Voltage | Accelerator Position Sensor No.2 Voltage |
|---|---|---|
| Fully Released | 0.5 to 1.1 V | 1.2 to 2.0 V |
| Fully Depressed | 2.6 to 4.5 V | 3.4 to 4.75 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Clutch Stroke Sensor Voltage | Clutch stroke sensor output voltage | Min.: 0.000 V
Max.: 4.999 V |
Value increases: Clutch pedal released → clutch pedal fully depressed | - |
| Tester Display |
|---|
| Clutch Stroke Sensor Voltage |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical > Main Body > Data List
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| FR Door Courtesy SW | Front door courtesy light switch assembly RH (for RHD) | ON or OFF | ON: Front door RH open
OFF: Front door RH closed |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| FL Door Courtesy SW | Front door courtesy light switch assembly LH (for LHD) | ON or OFF | ON: Front door LH open
OFF: Front door LH closed |
If this item does not change according to the actual state of the driver door, there is a malfunction in the door courtesy light switch or related part. |
| Tester Display |
|---|
| FR Door Courtesy SW |
| FL Door Courtesy SW |
The Data List item changes in accordance with the opening and closing of the driver door.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical > Main Body > Data List
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| D Seat Buckle SW | Driver seat belt buckle switch | OFF or ON | ON: Driver seat belt unfastened
OFF: Driver seat belt fastened |
- |
| Tester Display |
|---|
| D Seat Buckle SW |
Unset or Set is displayed on the GTS according to the driver seat belt condition.
| Result | Proceed to |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C