When ABS, TRC or VSC is operating, the skid control ECU (brake actuator assembly) blinks the slip indicator light to inform the driver that slippage occurred.
When in VSC off mode, or TRC and VSC are disabled, multi-information display in the combination meter assembly displays TRC OFF message and the VSC OFF indicator light illuminates to inform the driver.
When a communication malfunction with the ECM is detected, TRC and VSC are disabled. Also when the system is malfunctioning, TRC and VSC are disabled and the indicator lights of related systems illuminate.
When replacing the skid control ECU (brake actuator assembly), perform system variant learning.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION
Check if the slip indicator light was illuminated when TRC did not operate.
The slip indicator light was illuminated.
When a DTC is stored, the slip indicator light is illuminated and TRC does not operate due to the fail-safe function.
Check the operation condition of the VSC OFF switch (electric parking brake switch assembly) when TRC did not operate.
The VSC OFF switch (electric parking brake switch assembly) had been operated to turn off TRC when TRC did not operate.
When the multi-information display in the combination meter assembly displays "Traction Control Turned Off", TRC does not operate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Clear the DTCs.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON.
Check the DTCs (vehicle stability control system) that are output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output. | A |
| Vehicle stability control system DTCs are output. | B |
A
B
Operate the VSC OFF switch (electric parking brake switch assembly) and check that the multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.
The multi-information display in the combination meter assembly displays "Traction Control Turned Off" and the VSC OFF indicator light illuminates in accordance with the operation of the switch.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, perform a Test Mode (Signal Check) inspection sensor check and check that speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>TEST MODE PROCEDURE
| Tester Display |
|---|
| Signal Check |
Speed sensor Test Mode (Signal Check) inspection items change from incomplete to complete.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Operate the VSC OFF switch (electric parking brake switch assembly) and check that the system is not in TRC off mode or VSC off mode.
Check that no DTCs are output and that each warning light is not illuminated.
Start off the vehicle on a low friction surface and check that TRC operates when attempting to make the drive wheels slip.
TRC operates when slip occurs when starting off.
Even when the system is normal, VSC may not operate when the vehicle speed is low or TRC may not operate due to a malfunction. Make sure that only the drive wheels slip during the procedure.
When confirming that the slip indicator light blinks, do not slip the drive wheels longer than necessary. Whether TRC operated or not can be checked by reading the Freeze Frame Data when the system operated.
Pay attention to your surroundings when performing the procedure and depress the accelerator pedal with caution.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C