Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.09
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TEST MODE PROCEDURE  


WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK


a.

When the ignition switch is turned to ON, check that the ABS warning light, brake system warning light (red indicator), VSC OFF indicator light, multi-information display (TRC OFF message), brake hold standby indicator light, brake hold operated indicator light and slip indicator light come on for approximately 3 seconds.

HINT:
·

When the brake fluid level is low, the brake system warning light (red indicator) comes on.

·

If the skid control ECU (brake actuator assembly) stores a DTC, the ABS warning and slip indicator lights will come on.

·

If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.



Trouble Area See Procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake system warning light (red indicator) circuit (Remains on) (Click here)
Brake system warning light (red indicator) circuit (Does not come on) (Click here)
TRC OFF indicator light circuit (Remains on) (Click here)
TRC OFF indicator light circuit (Does not come on) (Click here)
VSC OFF indicator light circuit (Remains on) (Click here)
VSC OFF indicator light circuit (Does not come on) (Click here)
Slip indicator light circuit (Remains on) (Click here)
Slip indicator light circuit (Does not come on) (Click here)
Brake hold standby indicator light circuit (Click here)
Brake hold operated indicator light circuit (Click here)



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using GTS)


NOTICE:

Perform Test Mode with the vehicle stopped.


HINT:
·

DTCs are stored if any malfunctions are detected during the check of each sensor.

·

When entering test mode, the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit test mode within 5 seconds of entering test mode. (w/ Pre-collision System)



a.

Procedure to enter Test Mode

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is centered.


iii.

for Continuously Variable Transaxle:

Check that the shift lever is in P.


iv.

for Manual Transaxle:

Apply the parking brake.


v.

Connect the GTS to the DLC3.


vi.

Turn the ignition switch to ON.


vii.

Turn the GTS on.


viii.

Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC/EPB / Utility / Signal Check.

Chassis > ABS/VSC/TRC/EPB > Utility
Tester Display
Signal Check
50005 105 4359
HINT:

Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U0235 may be stored. If DTC U0235 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs. (w/ Precollision System)



ix.

Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the ABS warning and slip indicator light circuits.



x.

Check the ABS sensors.

HINT:

Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.




b.

Booster malfunction check (w/ Brake Pedal Load Sensing Switch)

i.

Depress the brake pedal several times with the engine stopped to release the vacuum from the brake booster assembly.


ii.

Turn the ignition switch on (IG) (engine stopped) and depress the brake pedal at a pedal force of approximately 74 N (7.5 kgf, 16.6 lfg) or above for 1 second or more and check that the warning light illuminates. (Malfunction check)


iii.

After the booster malfunction check is complete, maintain a pedal force of approximately 74 N (7.5 kgf, 16.6 lbf) or above on the brake pedal and turn on the engine. Immediately release the brake pedal and check that the warning light turns off. (Normal status check)

NOTICE:

Before checking again after starting the engine, exit and then activate the test mode and depress the brake pedal several times with the engine stopped to release the booster vacuum.




c.

VSC OFF Switch (electric parking brake switch assembly) Check

i.

Press the VSC OFF switch (electric parking brake switch assembly).


ii.

Check that the VSC OFF indicator light comes on.


iii.

Press the VSC OFF switch (electric parking brake switch assembly) again.



d.

Brake Hold Switch (electric parking brake switch assembly) Check

HINT:

Perform the check with the system in a normal condition.


i.

Make sure the following conditions are met:

·

The driver side door is closed.

·

The driver side seat belt is fastened.



ii.

Press the brake hold switch (electric parking brake switch assembly).


iii.

Check that the brake hold standby indicator light comes on.


iv.

Press the brake hold switch (electric parking brake switch assembly) again.



e.

Speed Sensor Check

i.

Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.

HINT:
·

The speed sensor check may not complete if wheelspin occurs.

·

The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel.



NOTICE:

After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again.

Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).



ii.

Check that the ABS warning light goes off.

HINT:
·

The ABS warning light goes off when the sensor check has completed.

·

The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.




iii.

Stop the vehicle.

HINT:

When the sensor check has completed, the ABS warning light goes off while the vehicle is being driven, and blinks in the Test Mode pattern while the vehicle is stopped.


NOTICE:

If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.




f.

End of Sensor Check

i.

When the sensor checks have completed, the ABS warning light goes off while the vehicle is being driven, and blinks in the Test Mode pattern while the vehicle is stopped.

NOTICE:
·

When the speed sensor and master cylinder pressure sensor checks are complete, the sensor check is complete.

·

If the sensor checks have not completed, the ABS warning light will remain blinking while the vehicle is being driven, and the ABS will not operate.

·

If any malfunctions are detected during Test Mode (Signal Check), the ABS warning light remains illuminated.

·

If any DTCs are output or if Test Mode (Signal Check) items do not complete even after repeated attempts, repair or replace the malfunctioning part.





g.

End of Test Mode (Signal Check)

i.

Turn the ignition switch off and disconnect the GTS.



h.

Test Mode (Signal Check) Inspection Item Chart

Item Name Range Judgment Description Trouble Area
Output Signal of Front Speed Sensor RH Incomplete/complete Check for foreign matter, evaluate the gap between the sensor and rotor
·

Open or short in speed sensor

·

Open or short in sensor system wire harness

·

Defective connector contact or increased terminal resistance

·

Speed sensor installation defect

·

Sensor rotor system malfunction


Output Signal of Front Speed Sensor LH Incomplete/complete Check for foreign matter, evaluate the gap between the sensor and rotor
·

Open or short in speed sensor

·

Open or short in sensor system wire harness

·

Defective connector contact or increased terminal resistance

·

Speed sensor installation defect

·

Sensor rotor system malfunction


Output Signal of Rear Speed Sensor RH Incomplete/complete Check for foreign matter, evaluate the gap between the sensor and rotor
·

Open or short in speed sensor

·

Open or short in sensor system wire harness

·

Defective connector contact or increased terminal resistance

·

Speed sensor installation defect

·

Sensor rotor system malfunction


Output Signal of Rear Speed Sensor LH Incomplete/complete Check for foreign matter, evaluate the gap between the sensor and rotor
·

Open or short in speed sensor

·

Open or short in sensor system wire harness

·

Defective connector contact or increased terminal resistance

·

Speed sensor installation defect

·

Sensor rotor system malfunction


Change in Output Signal of Front Speed Sensor RH Incomplete/complete
·

Evaluate the stability of the sensor input waveform

·

Evaluate the straight ahead / reverse signal inputs


·

Foreign object attached to speed sensor

·

Sensor rotor system malfunction


Change in Output Signal of Front Speed Sensor LH Incomplete/complete
·

Evaluate the stability of the sensor input waveform

·

Evaluate the straight ahead / reverse signal inputs


·

Foreign object attached to speed sensor

·

Sensor rotor system malfunction


Change in Output Signal of Rear Speed Sensor RH Incomplete/complete
·

Evaluate the stability of the sensor input waveform

·

Evaluate the straight ahead / reverse signal inputs


·

Foreign object attached to speed sensor

·

Sensor rotor system malfunction


Change in Output Signal of Rear Speed Sensor LH Incomplete/complete
·

Evaluate the stability of the sensor input waveform

·

Evaluate the straight ahead / reverse signal inputs


·

Foreign object attached to speed sensor

·

Sensor rotor system malfunction


Judgment of Failure State Incomplete/complete Check that the brake pedal load sensing switch is normal
·

Open or short in brake pedal load sensing switch system wire harness

·

Brake pedal load sensing switch stuck ON/OFF