Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE SYSTEM › 2019.09–2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292533 MANUAL TRANSAXLE SYSTEM J

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE SYSTEM  Pattern Select Switch iMT Mode Circuit  


DESCRIPTION

Operating the iMT switch illuminates the iMT indicator light in the combination meter assembly. This displays the iMT system standby condition.

WIRING DIAGRAM

C364974E02
0.51,3.229 4.177,3.427 3.667,0.198 10 false : CAN Communication Line 2.594,3.146 6.573,3.344 3.979,0.198 10 false Combination Meter Assembly 5.531,3.344 5.99,3.542 0.458,0.198 10 false ECM 2.573,1.25 4.292,1.667 1.719,0.417 10 false iMT Switch(Electric Parking Brake Switch Assembly) 2.948,0.74 3.406,0.938 0.458,0.198 10 false E 3.667,0.74 3.979,0.938 0.313,0.198 10 false S 5.24,0.74 5.854,0.938 0.615,0.198 10 false MTMS 5.917,0.438 6.531,0.635 0.615,0.198 10 false 12 V 2.573,1.052 3.031,1.25 0.458,0.198 10 false F67 4.927,0.74 5.24,0.938 0.313,0.198 10 false 36 3.885,0.51 4.458,0.813 0.573,0.302 10 false 11*1 0.25,2.344 2.854,2.542 2.604,0.198 10 false *1: for LHD 0.26,2.76 2.708,2.958 2.448,0.198 10 false *2: for RHD 5.542,3.167 6,3.365 0.458,0.198 10 false A38 2.76,0.719 3.219,0.917 0.458,0.198 10 false 8 3.906,0.719 4.365,0.917 0.458,0.198 10 false 13*2 5.25,2.708 5.865,2.906 0.615,0.198 10 false CANL 3.333,2.708 3.948,2.906 0.615,0.198 10 false CANL 3.323,2.281 3.938,2.479 0.615,0.198 10 false CANH 5.25,2.281 5.865,2.479 0.615,0.198 10 false CANH

PROCEDURE

1.READ VALUE USING GTS (iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List

Powertrain > Engine > Data List
Tester Display
iMT SW
50003 372 570

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
iMT SW iMT switch status ON or OFF
·

ON: iMT switch being pressed and held

·

OFF: iMT switch not pressed


-

Result:
Result Proceed to
Data display is not within Normal Condition range A
Data display is within Normal Condition range B



A

2.INSPECT iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

B

2.INSPECT iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
a.
C366035C21
1.417,0.115 1.844,0.333 0.427,0.219 2.271,1.438 2.604,1.781 true 1.719,1.448 1.906,1.885 true 1.365,1.448 1.063,1.865 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.542,0.156 2,0.354 0.458,0.198 10 false F67 0.844,1.885 1.302,2.083 0.458,0.198 10 false S*B 1.875,1.927 2.646,2.125 0.771,0.198 10 false S*A 2.656,1.813 3.427,2.01 0.771,0.198 10 false E
*A for LHD
*B for RHD
*a Component without harness connected
(iMT Switch (Electric Parking Brake Switch Assembly))


Disconnect the iMT Switch (Electric Parking Brake Switch Assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition
F67-11 (S) - F67-8 (E) Switch pushed Below 1 Ω
F67-11 (S) - F67-8 (E) Switch not pushed 10 kΩ or higher


Standard Resistance:

for RHD

Tester Connection Condition Specified Condition
F67-13 (S) - F67-8 (E) Switch pushed Below 1 Ω
F67-13 (S) - F67-8 (E) Switch not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the F67 iMT switch (Electric Parking Brake Switch Assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F67-8 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (iMT SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY) - ECM)
a.

Disconnect the F67 iMT switch (Electric Parking Brake Switch Assembly) connector.


b.

Disconnect the A38 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for LHD

Tester Connection Condition Specified Condition
F67-11 (S) - A38-36 (MTMS) Always Below 1 Ω
F67-11 (S) or A38-36 (MTMS) - Body ground Always 10 kΩ or higher


Standard Resistance:

for RHD

Tester Connection Condition Specified Condition
F67-13 (S) - A38-36 (MTMS) Always Below 1 Ω
F67-13 (S) or A38-36 (MTMS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT