Home › Drivetrain › GF1A (TRANSFER / 4WD / AWD) › DYNAMIC TORQUE CONTROL AWD SYSTEM › from 2019.09
RM32H0E _52 Drivetrain _059725 GF1A TRANSFER / 4WD / AWD _0298220 DYNAMIC TORQUE CONTROL AWD SYSTEM C

GF1A TRANSFER / 4WD / AWD  DYNAMIC TORQUE CONTROL AWD SYSTEM  C1241  Low or High Power Supply Voltage  


DESCRIPTION

If a malfunction in the power source circuit occurs, or a malfunction in communication with the skid control ECU (brake actuator assembly) or in a speed sensor occurs, the 4WD ECU assembly will prohibit operations by the fail-safe function.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low or High Power Supply Voltage
1.

When the following continues for 10 seconds or more:

-

At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less.


2.

When either of the following is detected:

-

With the IG1 terminal voltage 9.5 V or less, communication with the skid control ECU (brake actuator assembly) is impossible.

-

Vehicle speed sensor voltage is reduced for 60 seconds or more.


3.

When the following continues for 3 seconds or more:

-

With the IG1 terminal voltage 17 V or more, communication with the skid control ECU (brake actuator assembly) is impossible.



·

Battery

·

Charging system

·

Wire harness and connector (IG1 circuit, GND circuit)

·

Brake control system

·

CAN communication system

·

4WD ECU assembly



DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3
Diagnosis Condition - - - -
Malfunction Status At a vehicle speed of 3 km/h (2 mph) or more, voltage of IG1 terminal is 9.5 V or less. ○ - -
With the IG1 terminal voltage 9.5 V or less, communication with the skid control ECU (brake actuator assembly) is impossible. - ○ -
With the IG1 terminal voltage 17 V or more, communication with the skid control ECU (brake actuator assembly) is impossible. - - ○
Detection Time 10 seconds or more 60 seconds or more 3 seconds or more
Number of Trips 1 trip 1 trip 1 trip

HINT:

This DTC is output when any one of the above detection patterns is met.


WIRING DIAGRAM

C367131E01
1,1.208 2.99,1.406 1.99,0.198 10 false ECU-IG1 NO. 2 0.833,3.313 2.823,3.51 1.99,0.198 10 false : CAN Communication Line 3.76,2.906 5.75,3.104 1.99,0.198 10 false 4WD ECU Assembly 5.323,2.531 6.906,3.031 1.583,0.5 10 false Skid Control ECU (Brake Actuator Assembly) 3.823,0.927 4.156,1.208 0.333,0.281 10 false 3 3.823,1.802 4.156,2.083 0.333,0.281 10 false 4 4.031,1.042 4.448,1.292 0.417,0.25 10 false IG1 4.021,1.917 4.438,2.167 0.417,0.25 10 false GND 3.771,2.719 4.188,2.969 0.417,0.25 10 false M77

CAUTION / NOTICE / HINT

HINT:

Check the condition of each related circuit connector before troubleshooting.

Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE


PROCEDURE

1.CHECK FOR DTC (CAN COMMUNICATION SYSTEM AND BRAKE CONTROL SYSTEM)
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


b.

Start the engine.


c.

Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more for 60 seconds or more, and check if the speed sensor DTC (brake control system DTC) is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC/EPB > Trouble Codes
50001 105
Result:
Result Proceed to
Neither CAN communication system DTC nor speed sensor DTC (brake control system DTC) is output A
CAN communication system DTC is output B
Speed sensor DTC (brake control system DTC) is output C




A

2.INSPECT BATTERY

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

REPAIR CIRCUIT INDICATED BY OUTPUT CODE (BRAKE CONTROL SYSTEM)

2.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C270074C89
2.417,0.094 2.917,0.344 0.5,0.25 1.938,1.927 2.323,1.156 true 1.677,1.854 2.021,2.052 0.344,0.198 10 false IG1 2.542,0.104 2.854,0.302 0.313,0.198 10 false M77 0.104,0.083 0.417,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the 4WD ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M77-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND TERMINAL)
a.

Turn the ignition switch off.


b.
C270074C90
2.417,0.083 2.917,0.333 0.5,0.25 2.188,1.896 2.583,1.156 true 1.833,1.833 2.177,2.031 0.344,0.198 10 false GND 2.531,0.094 2.948,0.281 0.417,0.188 10 false M77 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M77-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.RECONFIRM DTC
a.

Clear the DTC.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Clear DTCs
50002 118

b.

Start the engine.


c.

Drive the vehicle, accelerate to a speed of 3 km/h (2 mph) or more, and check if the same DTC is output.

Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR

Chassis > Four Wheel Drive > Trouble Codes
50001 118
Result:
Result Proceed to
DTC is output A
DTC is not output B


HINT:

Reinstall the sensor, connectors, etc. and restore the vehicle to its prior condition before rechecking DTCs.




A

B