The 4WD ECU assembly determines that the vehicle is turning based on the signals sent from the steering sensor.
The steering angle sensor signal is sent to the 4WD ECU assembly via the CAN communication system.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1297 | Steering Angle Sensor | When voltage of 4WD ECU assembly IG terminal is 9.5 V or more, and steering sensor malfunction signal is received. | ·
ECU-DCC NO. 1 Fuse ·
Steering sensor ·
CAN communication system ·
4WD ECU assembly ·
Wire harness and connector |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the condition of each related circuit connector before troubleshooting.
Clear the DTC.
Click hereDrivetrain>GF1A (TRANSFER / 4WD / AWD)>DYNAMIC TORQUE CONTROL AWD SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON again and check that no CAN communication system DTC(s) is output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Start the engine.
Drive the vehicle at a speed of 35 km/h (24 mph), turn the steering wheel to the right and left and check that no brake control system (steering angle sensor) DTC (C1432, C1433 or C1434) is output.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| Neither CAN communication system DTC nor brake control system DTC is output | A |
| CAN communication system DTC is output | B |
When DTCs indicating a CAN communication system malfunction are output, repair the CAN communication system before repairing each corresponding sensor.
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
| *a | Front view of wire harness connector
(to Steering Sensor) |
Remove the steering wheel and the column cover lower.
Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL
Make sure that there is no looseness at the locking part and the connecting part of the connectors.
Disconnect the steering sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-5 (BAT) - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch to ON.
| *a | Front view of wire harness connector
(to Steering Sensor) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| F69-4 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
| *a | Front view of wire harness connector
(to Steering Sensor) |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F69-1 (ESS) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / Four Wheel Drive / Data List.
Read the value displayed on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Angle Value | Steering angle value | Min.: -3276.8°
Max.: 3276.7° |
Left turn: Increase
Right turn: Decrease |
Changes in proportion with the amount of steering wheel rotation during steering operation. |
| Tester Display |
|---|
| Steering Angle Value |
The steering angle sensor value changes in accordance with the steering wheel movement.
| Proceed to |
|---|
| OK |
| NG |
OK
NG