Home › Suspension › REAR SUSPENSION › REAR TRAILING ARM › from 2019.09
RM32H0E _53 Suspension _059601 REAR SUSPENSION _0292269 REAR TRAILING ARM A

REAR SUSPENSION  REAR TRAILING ARM  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 48727 1.INSTALL REAR SUSPENSION ARM BRACKET

a.

Temporarily install the rear suspension arm bracket to the rear trailing arm assembly with the bolt and nut.

NOTICE:
·

Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.

·

Insert the bolt from the inside of the vehicle.




b.
C365340C01
1.75,0.927 2.083,0.583 2.083,0.583 2.25,0.583 false 2.469,3.26 2.583,3.583 2.583,3.583 2.75,3.583 false 2.302,0.458 2.615,0.656 0.313,0.198 10 false *a 3.125,1.292 3.354,1.5 0.229,0.208 10 false A 2.844,3.458 3.156,3.656 0.313,0.198 10 false *b
*a Upper Surface of Rear Suspension Arm Bracket
*b Edge of Rear Trailing Arm Assembly


Position the rear trailing arm assembly as shown in the illustration.

Reference Length (A):

150 mm (5.91 in.)



c.

Fully tighten the nut.

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)

NOTICE:

Because the bolt has its own stopper, do not turn the bolt. Tighten the nut with the bolt secured.



Hide 48753C 2.INSTALL NO. 1 REAR SUSPENSION SUPPORT COVER

a.

Engage the 3 claws to install the NO. 1 rear suspension support cover.


Hide 48780E 3.INSTALL REAR TRAILING ARM ASSEMBLY

a.

Using a transmission jack and a wooden block, support the rear No. 2 suspension arm assembly.

NOTICE:
·

When jacking up the rear No. 2 suspension arm assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




b.

Install the rear trailing arm assembly to the vehicle with the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


c.

Install the rear trailing arm assembly to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
135 N*m (1377 kgf*cm, 100 ft.*lbf)


Hide 890C0A 4.INSTALL NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Engage the clamp.


b.

Install the No. 2 parking brake wire assembly to the rear trailing arm assembly with the nut.

Torque:
15.5 N*m (158 kgf*cm, 11 ft.*lbf)


c.

for 2WD:

i.

Connect the No. 2 parking brake wire connector to the rear axle hub and bearing assembly.



d.

for AWD:

i.

Connect the No. 2 parking brake wire connector to the rear axle hub and bearing assembly.



Hide 48840A 5.INSTALL REAR STABILIZER LINK ASSEMBLY

Hide 57628C 6.INSTALL REAR FLOOR SIDE MEMBER COVER LH (for 2WD)

Hide 57627A 7.INSTALL REAR FLOOR SIDE MEMBER COVER RH (for 2WD)

Hide 57628C 8.INSTALL REAR FLOOR SIDE MEMBER COVER LH (for AWD)

Hide 57627A 9.INSTALL REAR FLOOR SIDE MEMBER COVER RH (for AWD)

Hide 10.INSTALL REAR WHEEL

Hide 11.INSPECT AND ADJUST REAR WHEEL ALIGNMENT

Hide 13.PERFORM CALIBRATION

·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Panoramic view monitor system (Click here)