Home › Drivetrain › EC6A (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › 2019.09–2020.08
RM32H0E _52 Drivetrain _059609 EC6A MANUAL TRANSMISSION / TRANSAXLE _0292324 MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

EC6A MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the manual transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Toyota parking assist-sensor system*1
Parking support brake system*1
Simple intelligent parking assist system*1
Pre-collision system
Memorize steering angle neutral point Panoramic view monitor system (Click here)
Initialize back door lock Power door lock control system (Click here)
Front wheel alignment adjustment w/ VSC:
Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)


CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the manual transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Hide 28100 3.REMOVE STARTER ASSEMBLY (for Cold Area Specification Vehicles)

Hide 28100 4.REMOVE STARTER ASSEMBLY (except Cold Area Specification Vehicles)

Hide 11363A 5.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 6.DISCONNECT WIRE HARNESS

a.
C366688C01
3,2.813 3.219,3.01 0.219,0.198 10 true *1 1.271,2.333 1.49,2.531 0.219,0.198 10 true *2
*1 Back-up Light Switch Assembly Connector
*2 Transmission Revolution Sensor Connector


Disconnect the back-up light switch assembly connector.


b.

Disconnect the transmission revolution sensor connector.


c.

Remove the bolt.


d.

Disengage the clamp and separate the wire harness from the manual transaxle assembly.


e.
C366690

Disengage the 3 clamps and separate the heated oxygen sensor wire harness from the front suspension crossmember sub-assembly.


f.
C366691

Disconnect the neutral position switch connector.


g.

Disengage the 3 clamps and separate the wire harness from the manual transaxle assembly.


Hide 12321B 7.REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

Hide 25591 8.REMOVE MANIFOLD SUPPORT BRACKET

Hide 9.REMOVE ENGINE ASSEMBLY

a.
C187765E01
2.26,0.031 2.417,0.229 0.156,0.198 10 false A 1.177,0.042 1.333,0.24 0.156,0.198 10 false A 0.74,0.854 0.896,1.052 0.156,0.198 10 true B 1.073,1.76 1.229,1.958 0.156,0.198 10 true B 2.5,1.854 2.656,2.052 0.156,0.198 10 false B 2.052,1.958 2.24,2.146 0.188,0.188 10 false B 1.438,2.01 1.615,2.177 0.177,0.167 10 false B

Remove the 7 bolts and engine assembly from the manual transaxle assembly.

HINT:
·

Bolt (A): Remove from manual transaxle assembly side.

·

Bolt (B): Remove from engine assembly side.




Hide 51201 10.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.
C365145

Remove the bolt and front suspension crossmember sub-assembly from the No. 2 engine moving control rod.


Hide 12364B 11.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

C366699

a.

Remove the 4 bolts and No. 2 engine moving control rod from the manual transmission case.


Hide 12325A 12.REMOVE ENGINE MOUNTING BRACKET LH

a.
C366693

Remove the 5 bolts and engine mounting bracket LH from the manual transmission case.


Hide 31483E 13.REMOVE BLEEDER CLUTCH RELEASE TUBE

Hide 31484 14.REMOVE CLUTCH FLEXIBLE HOSE BRACKET

a.
C356498

Remove the bolt and clutch flexible hose bracket from the manual transmission case.


Hide 31407B 15.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31400 16.REMOVE CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31483 17.REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

Hide 87101A 18.REMOVE NO. 1 HEATER BRACKET SUB-ASSEMBLY

a.
C366689

Remove the bolt and No. 1 heater bracket sub-assembly from the manual transmission case.


Hide 19.REMOVE WIRE HARNESS CLAMP BRACKET

C366692

a.

Remove the bolt and wire harness clamp bracket from the manual transmission case.


Hide 335A0 20.REMOVE CONTROL CABLE BRACKET ASSEMBLY

a.
C366698

Remove the 3 bolts and control cable bracket assembly from the manual transmission case.


Hide 21.REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY

a.
C356500

Remove the bolt and speedometer driven hole cover sub-assembly from the front transaxle case.


b.

Remove the O-ring from the speedometer driven hole cover sub-assembly.