Home › Drivetrain › K114 (MULTIDRIVE / CVT) › CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge) › 2019.09–2020.08
RM32H0E _52 Drivetrain _059616 K114 MULTIDRIVE / CVT _0292459 CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge) A

K114 MULTIDRIVE / CVT  CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY(When Using the Engine Support Bridge)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the continuously variable transaxle assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Toyota parking assist-sensor system*1 (Click here)
Simple intelligent parking assist system*1
Initialize back door lock Power door lock control system (Click here)
·

Air leaks from intake system

·

Gas leaks from exhaust system


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Replacement of continuously variable transaxle assembly Perform the following procedures in the order shown:
1.

Reset memory

2.

Deceleration sensor zero point calibration

3.

CVT oil pressure calibration


Deterioration of fuel efficiency (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)
Initialize No. 1 headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

CAUTION:
·
C313282C01
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Heavy object exceeding the capacity of the transmission jack


Because the continuously variable transaxle assembly is extremely heavy, make sure to follow the work procedures described in the repair manual.

·

If work is not performed according to the procedures described in the repair manual, there is a danger that the transmission jack could drop and components could fall down.


·
A344784

When the engine is hot, do not touch high-temperature areas such as the engine or exhaust pipe.

·

Touching high-temperature areas such as the engine and exhaust pipe could result in burns.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>3ZR-FAE BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 4.REMOVE FRONT WHEELS

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 6.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 7.REMOVE REAR ENGINE UNDER COVER RH

Hide 8.DRAIN ENGINE COOLANT

Hide 9.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 10.REMOVE WINDSHIELD WIPER MOTOR AND LINK

Hide 55737B 11.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55736D 12.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 13.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 14.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 28800 15.REMOVE BATTERY

Hide 53141F 17.REMOVE RADIATOR COVER

Hide 17751 18.REMOVE NO. 1 AIR CLEANER INLET

Hide 17705 19.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17701 20.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 22.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
A393409

Remove the bolt and nut to separate the engine wire from the battery clamp sub-assembly.


b.
A393412

Disengage the clamp to separate the engine wire from the battery clamp sub-assembly.


c.

Remove the 3 bolts and battery clamp sub-assembly from the vehicle.


Hide 33820B 23.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C296239

Remove the nut to disconnect the transmission control cable assembly from the control shaft lever.


b.

Remove the clip to disconnect the transmission control cable assembly from the No. 1 transmission control cable bracket.


c.
C365140

Remove the nut to disconnect the transmission control cable assembly from the transmission control cable support.


Hide 16267 24.DISCONNECT NO. 3 WATER BY-PASS HOSE

a.
C315507

Slide the clip and disconnect the No. 3 water by-pass hose from the oil cooler.


Hide 16282 25.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
C315508

Slide the clip and disconnect the No. 5 water by-pass hose from the oil cooler.


b.

Disconnect the No. 5 water by-pass hose from the 2 clamps.


Hide 82121 26.DISCONNECT ENGINE WIRE

a.

Disconnect the park/neutral position switch connector.

C365130C01
1.167,2.083 1.375,2.281 0.208,0.198 10 true *1 1.594,2.229 1.802,2.427 0.208,0.198 10 true *2 2.344,1.063 2.521,1.24 0.177,0.177 10 true *3 6.448,0.917 6.688,1.083 0.24,0.167 10 true *4 1.385,1.229 1.594,1.396 0.208,0.167 10 true *5 4.792,1.979 5.01,2.146 0.219,0.167 10 true *6
*1 Park/Neutral Position Switch Connector *2 Transmission Wire Connector
*3 Transmission Revolution Sensor (NIN) Connector *4 Transmission Revolution Sensor (NOUT) Connector
*5 Transmission Revolution Sensor (NT) Connector *6 Oil Pressure Sensor Connector



b.

Disconnect the transmission wire connector.


c.

Disconnect the transmission revolution sensor (NIN) connector.


d.

Disconnect the transmission revolution sensor (NT) connector.


e.

Disconnect the transmission revolution sensor (NOUT) connector.


f.

Disconnect the oil pressure sensor connector.


g.

Remove the 3 bolts and nut to disconnect the engine wire from the continuously variable transaxle assembly.


h.

Disengage the 5 clamps to disconnect the engine wire from the continuously variable transaxle assembly.


Hide 33823 27.REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.
C295568

Disconnect the clamp from the No. 1 transmission control cable bracket.


b.

Remove the 2 bolts and No. 1 transmission control cable bracket from the continuously variable transaxle assembly.


Hide 45100 28.SECURE STEERING WHEEL ASSEMBLY

Hide 45259A 29.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 30.SEPARATE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 31.SEPARATE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 57533B 32.REMOVE FRONT FLOOR CENTER BRACE

Hide 17410 33.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Front and Rear Catalyst)

Hide 35.INSTALL ENGINE HANGER

a.
A393422

Disengage the 5 clamps.


b.

Disconnect the air fuel ratio sensor connector.


c.

Remove the bolt and wire harness clamp bracket.


d.
A317993C03
0.969,1.031 1.438,1.031 true 2.385,1.021 2.854,1.021 true 1.458,0.948 1.771,1.146 0.313,0.198 10 true *1 2.115,0.927 2.396,1.125 0.281,0.198 10 true *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger
V100135

Bolt


Install the No. 1 engine hanger and No. 2 engine hanger with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37070
No. 2 Engine Hanger 12282-37060
Bolt 91552-81050



Hide 36.INSTALL ENGINE SUPPORT BRIDGE

a.
C364030

Remove the clip and the neck from the windshield washer jar assembly.


b.

Install SST to the vehicle body as shown in the illustration.

C366452C01
1.625,1.229 1.823,1.021 true 5.177,1.271 4.896,1.094 true 6.177,2.917 5.833,3.125 false 1.781,5.333 2.625,5.073 true 2.042,6.042 2.344,6.177 true 4.406,5.01 5.292,5.313 true 4.594,6.063 4.979,6.063 true 2.635,4.99 2.833,5.177 0.198,0.188 10 true *a 2.354,6.115 2.531,6.281 0.177,0.167 10 true *b 1.521,1.229 1.719,1.396 0.198,0.167 10 true *c 5.083,1.271 5.281,1.438 0.198,0.167 10 true *c 6.208,2.844 6.667,3.042 0.458,0.198 10 false SST 4.208,4.906 4.406,5.094 0.198,0.188 10 true *a 4.406,5.969 4.583,6.135 0.177,0.167 10 true *b
*a Support Shaft *b Front Side Member
*c Front Suspension Nut - -


SST
09940-10020  

CAUTION:
·
C330755C01
0.448,1.167 0.781,1.167 false 2.438,1.167 2.771,1.167 false 1.052,1.781 1.052,1.448 1.052,1.448 1.219,1.448 false 2.604,1.781 2.604,1.448 2.604,1.448 2.438,1.448 false 0.292,1.094 0.604,1.25 0.313,0.156 10 false *a 2.271,1.094 2.583,1.25 0.313,0.156 10 false *a 1.281,1.385 1.594,1.542 0.313,0.156 10 false *b 2.271,1.385 2.583,1.542 0.313,0.156 10 false *b
*a Support Shaft
*b Front Side Member


Make sure that no oil or grease is on the front side member, and set the support shaft on the level surface of the front side member.

·

The engine support bridge may fall off if any oil or grease is still on or it is installed on the unlevel surface.



NOTICE:
·

Prevent SST from contacting the vehicle body exterior and windshield glass.

·

To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.

·

Lightly shake SST by hand to make sure it is securely installed before performing work.




c.
C338947C01
0.615,1.479 0.615,0.656 0.615,0.656 0.5,0.656 false 1.042,2.125 1.667,2.125 false 1.031,2.469 2.167,2.469 false 0.875,2.771 0.875,2.458 0.875,2.458 0.76,2.458 false 1.708,2.01 2.063,2.281 0.354,0.271 10 false *a 0.292,0.552 0.604,0.823 0.313,0.271 10 false *b 0.552,2.354 0.917,2.583 0.365,0.229 10 false *c 2.208,2.375 2.563,2.667 0.354,0.292 10 false *d
*a Support Shaft
*b Sub Beam
*c Front Side Member
*d Threaded Portion


Turn the threaded portion of each support shaft to adjust its height until the sub beams are parallel to the ground.


d.

Install the chain block to the sling bracket.

C366453C01
1.583,1 1.885,1 false 0.427,0.604 1.302,0.604 true 0.875,1.167 1.313,1.469 true 1.042,1.531 1.313,1.531 true 1.927,0.906 2.24,1.063 0.313,0.156 10 false *a 0.229,0.49 0.542,0.646 0.313,0.156 10 false *b 0.719,1.031 1.031,1.188 0.313,0.156 10 false *c 0.813,1.448 1.021,1.615 0.208,0.167 10 true *d
*a Chain Block *b Sling Bracket
*c Fuse Shackle *d Shackle (A)



e.

Install the division bar to the chain block with the shackles.

CAUTION:
·
C338949C01
0.458,2.313 0.583,2.313 0.583,2.313 0.875,2.635 false 0.354,2.677 0.479,2.677 0.479,2.677 0.865,2.865 false 2.177,2.271 2.302,2.271 2.302,2.271 2.604,2.594 false 2.073,2.656 2.198,2.656 2.198,2.656 2.583,2.844 false 0.281,2.208 0.604,2.469 0.323,0.26 10 false *a 0.167,2.573 0.51,2.844 0.344,0.271 10 false *b 1.99,2.156 2.313,2.417 0.323,0.26 10 false *a 1.885,2.542 2.229,2.813 0.344,0.271 10 false *b
*a Fuse Shackle
*b Shackle (A)


Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.

·

If the fuse shackle is installed upside down, deformation of the fuse bolt will not be visible and cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with automatic transaxle assembly may fall.

·
C330757C01
2.75,1 3.083,1 false 1.01,1 1.344,1 false 0.917,1.417 1.333,1.583 true 2.635,1.396 3.083,1.583 true 1.396,0.917 1.708,1.073 0.313,0.156 10 false *a 1.385,1.51 1.698,1.667 0.313,0.156 10 false *b 3.125,0.917 3.354,1.083 0.229,0.167 10 false *a 3.135,1.5 3.354,1.667 0.219,0.167 10 false *b
*a Fuse Shackle
*b Fuse Bolt


Make sure that the fuse bolt of the fuse shackle is free of damage, such as deformation or cracks. If damaged, replace the fuse shackle.

·

If a deformed fuse bolt is used, it cannot be used to tell if the load capacity of the engine support bridge has been exceeded. If the load capacity is exceeded, it may cause the engine support bridge to damage the vehicle and the engine assembly with transaxle assembly may fall.




f.

Connect the division bar to the No. 1 engine hanger with the shackle (A) and chain.

C366454C01
1.031,1.76 1.313,1.604 true 1.75,1.813 2.167,1.625 true 1.26,1.365 1.677,1.115 true 0.594,1.094 0.948,0.677 true 0.635,3.948 1.208,3.823 true 1.302,4.813 2.01,4.542 true 1.417,3.646 1.74,3.854 true 2.26,3.833 2.052,3.51 true 2.052,4.448 2.26,4.625 0.208,0.177 10 true *1 2.24,1.542 2.427,1.698 0.188,0.156 10 true *2 0.958,0.573 1.156,0.74 0.198,0.167 10 true *a 1.698,1.021 1.896,1.188 0.198,0.167 10 true *b 0.833,1.688 1.031,1.854 0.198,0.167 10 true *c 0.427,3.875 0.625,4.042 0.198,0.167 10 true *c 1.76,3.792 1.958,3.958 0.198,0.167 10 true *b 2.208,3.854 2.406,4.021 0.198,0.167 10 true *a
*1 No. 1 Engine Hanger *2 No. 2 Engine Hanger
*a Division Bar *b Shackle (A)
*c Chain - -


NOTICE:

Connect the 2nd link of the chain to the No. 1 engine hanger.



g.

Connect the division bar to the No. 2 engine hanger with the shackle (A) and chain.

NOTICE:

Connect the 2nd link of the chain to the No. 2 engine hanger.



h.
C330764C02
1.219,0.792 1.531,0.948 0.313,0.156 10 false *a
*a 120 mm (4.72 in.) or more


Make sure the distance between the chain block assembly and suspension ring is 120 mm (4.72 in.) or more.

HINT:

If the suspension height is less than 120 mm, adjust the links of the chain which connect the division bar and engine hanger.



i.

Adjust the positions of the chain block assembly, support brackets and main beam so that the chain of the chain block assembly is perpendicular to the main beam and the length of the main beam on the outer side of the support bracket LH and RH is the same as shown in the illustration.

C366455C01
3.365,1.479 3.615,1.479 true 4.271,0.958 4.604,0.625 false 3.635,1.396 3.854,1.573 0.219,0.177 10 true *a 4.635,0.51 4.948,0.667 0.313,0.156 10 false *b 6.125,0.448 6.438,0.604 0.313,0.156 10 false *c 1.01,0.438 1.323,0.594 0.313,0.156 10 false *d 3.031,0.365 3.344,0.521 0.313,0.156 10 false *e 0.969,2.323 1.135,2.5 0.167,0.177 10 true *f 6.115,2.354 6.281,2.531 0.167,0.177 10 true *f
*a Chain Block *b Main Beam
*c Dimension (A) *d Dimension (B)
*e Right to Left Adjustment *f Front to Rear Adjustment


CAUTION:
·

To prevent the engine with automatic transaxle assembly from falling, make sure that the length of dimension (A) and dimension (B) are equal.

·
C366456C01
1.917,1.49 2.188,1.188 false 2.167,1.01 2.479,1.167 0.313,0.156 10 false *a
*a Main Beam


Do not perform any procedures if the length of dimension (A) and dimension (B) are not equal.

·

Performing any procedure when the length of dimension (A) and dimension (B) are not equal may cause the engine assembly with automatic transaxle assembly and engine support bridge to fall, possibly causing serious injury.




j.

Confirm the appropriate installation state of the engine support bridge and tighten the 6 wing bolts and 2 bolts.

C366457C01
2.063,0.063 2.26,0.24 0.198,0.177 10 false *a 1.292,1.708 1.5,1.885 0.208,0.177 10 true *b 4.854,0.063 5.052,0.24 0.198,0.177 10 false *a 1.76,1.021 1.958,1.198 0.198,0.177 10 true *a 2.479,1.052 2.677,1.229 0.198,0.177 10 true *a 4.375,1.021 4.573,1.198 0.198,0.177 10 true *a 5.146,1.052 5.344,1.229 0.198,0.177 10 true *a 5.531,1.583 5.74,1.76 0.208,0.177 10 true *b
*a Wing Bolt *b Bolt


Torque:
Bolt : 30 N*m (306 kgf*cm, 22 ft.*lbf)

CAUTION:
·
C330761

Do not perform any procedures before tightening the bolts to the specified torque.

·

Performing procedures without tightening the bolts to the specified torque, may cause the engine support bridge to fall.




k.
C366458C01
2.573,3.063 2.771,3.25 0.198,0.188 10 true *a
*a Turn


Tighten the chain block assembly until it cannot be moved any further by hand.

CAUTION:
C330770C01
2.99,2.292 3.302,2.448 0.313,0.156 10 false *a
*a 41 N*m (418 kgf*cm, 30 ft.*lbf) or more


·

When suspending the engine with automatic transaxle assembly, do not tighten the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf).

·

Tightening the chain block assembly more than 41 N*m (418 kgf*cm, 30 ft.*lbf) will cause the load capacity (400 kg (881.8 lb)) to be exceeded and may cause damage to the engine support bridge and vehicle body.




Hide 51108A 37.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 38.REMOVE REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

Hide 51201 39.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 12364B 40.REMOVE NO. 2 ENGINE MOVING CONTROL ROD

a.
C365147

Remove the 4 bolts and No. 2 engine moving control rod from the continuously variable transaxle assembly.


Hide 30400 41.SUPPORT CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C366435C01
1.792,0.917 1.344,0.865 true 1.156,0.76 1.333,0.938 0.177,0.177 10 true *a
*a Lashing Belt


Using a transmission jack, support the continuously variable transaxle assembly.

NOTICE:
·

Adjust the attachment of the transmission jack to securely fix the continuously variable transaxle assembly to the transmission jack.

·

To prevent the transaxle oil (CVT) pan sub-assembly from deforming, do not place any attachments under the transaxle oil (CVT) pan sub-assembly of the continuously variable transaxle assembly.

·

Using a lashing belt or a rope, fix the continuously variable transaxle assembly to the transmission jack.




Hide 28100 42.REMOVE STARTER ASSEMBLY

Hide 11363A 43.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 11361J 44.REMOVE FLYWHEEL HOUSING UNDER COVER

a.
C297722

Remove the flywheel housing under cover.


Hide 32101G 45.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
C300744

Turn the crankshaft to gain access to the 6 drive plate and torque converter assembly setting bolts and remove each drive plate and torque converter assembly setting bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored drive plate and torque converter assembly setting bolt.



Hide 12372A 46.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING INSULATOR

a.
C366441

Remove the bolt and nut to separate the engine mounting insulator LH from the transverse engine engine mounting bracket.


b.
C366442

Remove the nut and 4 bolts.


c.

Remove the engine mounting insulator LH from the vehicle body.


Hide 12325A 47.REMOVE TRANSVERSE ENGINE ENGINE MOUNTING BRACKET

a.
C365132

Remove the 5 bolts and transverse engine engine mounting bracket from the continuously variable transaxle assembly.


Hide 30400 48.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY

a.
C295575

Remove the 8 bolts and continuously variable transaxle assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the continuously variable transaxle assembly and engine assembly.



Hide 32000A 49.REMOVE TORQUE CONVERTER ASSEMBLY

a.

Remove the torque converter assembly from the continuously variable transaxle assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 30400E 50.REMOVE CVT OIL PUMP TYPE T OIL SEAL

CAUTION:
·

Do not remove the front oil pump assembly from the continuously variable transaxle assembly main body, as there is a possibility of the entry of dust and foreign matter.

·

Clean the work area, the tools to be used, and other equipment, etc. thoroughly before the operation, as there is the possibility that a continuously variable transaxle assembly malfunction, which may prevent the vehicle from being driven, may occur if dust or fine foreign matter enters the continuously variable transaxle assembly.

·

Do not use cotton work gloves, cloths, paper towels, etc. that may produce lint, dust or foreign matter.

·

Perform the operation as quickly as possible, as dust and foreign matter may enter the continuously variable transaxle assembly while the torque converter assembly is not attached to it.

·

Do not use an air gun until the torque converter assembly has been installed, as it may cause dust and foreign matter to be stirred up.



a.

Clean the tips of both the claws of SST and the center bolt.

SST
09308-10010  


b.
C208788C02
2.406,2.073 2.406,2.604 false 0.979,1.25 1.302,0.781 1.302,0.781 1.563,0.781 false 1.802,2.531 1.542,2.531 1.542,2.531 1.271,1.865 false 2.302,2.646 2.76,2.844 0.458,0.198 10 false SST 1.604,0.677 1.99,1.104 0.385,0.427 10 false *1 1.844,2.417 2.271,2.833 0.427,0.417 10 false *a
*1 CVT Oil Pump Type T Oil Seal
*a Claw


Using SST, remove the CVT oil pump type T oil seal from the continuously variable transaxle assembly.

NOTICE:

Pay attention to the angle of the claws of SST when opening them, and ensure that they do not come into contact with the oil pump housing, as there is the possibility that metal particles may be produced if they do.



Hide 51.REMOVE TRANSMISSION CONTROL CABLE SUPPORT

a.
C315509

Remove the 2 bolts and transmission control cable support from the continuously variable transaxle assembly.


Hide 52.REMOVE WIRE HARNESS CLAMP BRACKET

a.
C365123C01
1.833,4 2.219,3.719 true 2.573,3.594 2.917,3.333 false 2.917,2.083 2.167,1.292 true 0.688,1.083 1,1.083 true 0.25,0.458 0.5,0.594 true 2.938,3.198 3.177,3.396 0.24,0.198 10 false *1 0.073,0.344 0.385,0.5 0.313,0.156 10 false *2 1.01,0.99 1.24,1.167 0.229,0.177 10 true *3 1.635,3.969 1.875,4.167 0.24,0.198 10 true *1 2.958,2.052 3.198,2.25 0.24,0.198 10 false *1
*1 Wire Harness Clamp Bracket
*2 Water By-pass Hose Clamp
*3 Water Hose Clamp Bracket


Remove the bolt and water hose clamp bracket from the continuously variable transaxle assembly.


b.

Remove the water by-pass hose clamp from the water hose clamp bracket.


c.

Remove the 3 bolts and 3 wire harness clamp brackets from the continuously variable transaxle assembly.


Hide 32921Y 53.REMOVE TUBE CONNECTOR

a.
C296963

Slide the clip and disconnect the No. 1 transmission oil cooler hose from the tube connector.

NOTICE:

Do not damage the coating of the hose insertion part of the tube connector.



b.

Remove the tube connector from the continuously variable transaxle assembly.


c.

Remove the O-ring from the tube connector.


Hide 32901F 54.REMOVE OIL COOLER ELBOW SUB-ASSEMBLY

a.
C296964

Slide the clip and disconnect the No. 2 transmission oil cooler hose from the oil cooler elbow sub-assembly.

NOTICE:

Do not damage the coating of the hose insertion part of the oil cooler elbow sub-assembly.



b.

Remove the union bolt, oil cooler elbow sub-assembly and gasket from the continuously variable transaxle assembly.


Hide 35151K 55.REMOVE AUTOMATIC TRANSMISSION CASE COVER

a.
C297207

Remove the 2 clips and automatic transmission case cover from the continuously variable transaxle assembly.


Hide 56.REMOVE STRAIGHT SCREW PLUG

HINT:

Perform this procedure only when replacement of the straight screw plug is necessary.


a.
C316583

Remove the straight screw plug and gasket from the continuously variable transaxle assembly.


Hide 35012B 57.REMOVE TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

HINT:

Perform this procedure only when replacement of the transmission breather hose sub-assembly is necessary.


a.
C295577C02
2.51,0.51 2.875,0.51 false 2.938,0.438 3.25,0.635 0.313,0.198 10 false *1
*1 Transmission Breather Hose Sub-assembly


Remove the transmission breather hose sub-assembly from the continuously variable transaxle assembly.


b.
C365133C01
2.698,2 3.031,2 false 2,1.667 2.333,1.667 false 0.615,0.333 0.917,0.167 false 2.25,0.76 2.583,0.5 false 0.948,0.063 1.26,0.219 0.313,0.156 10 false *1 2.615,0.396 2.927,0.552 0.313,0.156 10 false *2 1.802,1.563 2.115,1.719 0.313,0.156 10 false *3 3.063,1.896 3.375,2.052 0.313,0.156 10 false *4
*1 No. 1 Breather Plug (CVT)
*2 Breather Plug Hose
*3 No. 2 Breather Plug (CVT)
*4 O-ring


Remove the No. 1 breather plug (CVT) and No. 2 breather plug (CVT) from the breather plug hose.


c.

Remove the O-ring from the breather plug.


Hide 32000A 58.INSPECT TORQUE CONVERTER ASSEMBLY

Hide 32101B 59.INSPECT DRIVE PLATE AND RING GEAR SUB-ASSEMBLY