Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL (for RHD) › from 2019.09
RM32H0E _54 Brake _060040 BRAKE SYSTEM (OTHER) _0298587 BRAKE PEDAL(for RHD) N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL(for RHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE PEDAL HEIGHT

a.

Remove the No. 1 air duct.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL



b.

Check the brake pedal height.

NOTICE:
·

Inspect and adjust the brake pedal height with the floor carpet folded back.

·

When performing the measurement, make sure that the measuring device is contacting the surface of the dash panel insulator assembly clip.



i.

Measure the shortest distance between the brake pedal pad surface and dash panel insulator assembly clip.

C366059C01
2.24,1.698 2.24,1.406 true 5.49,0.885 5.771,0.656 true 5.177,2.281 5.51,2.125 true 2.177,1.74 2.406,1.948 0.229,0.208 10 true *1 0.406,1.396 0.635,1.625 0.229,0.229 10 true *a 5,2.24 5.313,2.396 0.313,0.156 10 false *2 5.823,0.531 6.052,0.74 0.229,0.208 10 true *1
*1 Brake Pedal Pad *2 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height - -


Brake Pedal Height from Dash Panel Insulator Assembly Clip:

173.5 to 185.5 mm (6.83 to 7.30 in.)


HINT:

for Manual Transaxle:

Perform the inspection with the clutch pedal depressed.


If the pedal height is not as specified, adjust the brake pedal height according to the procedure below.



c.

Adjust the brake pedal height.

i.
C368090C01
2.406,1.115 2.729,0.99 false 1.542,1.969 1.76,1.677 false 1.25,3.865 1.813,3.719 true 2.792,0.896 3.104,1.052 0.313,0.156 10 false *1 1.417,2 1.729,2.156 0.313,0.156 10 false *2 2.573,3.729 2.885,3.885 0.313,0.156 10 false *a 1.073,3.802 1.385,3.958 0.313,0.156 10 false *3
*1 Stop Light Switch Assembly
*2 Clevis Lock Nut
*3 Dash Panel Insulator Assembly Clip
*a Brake Pedal Height


Remove the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL


ii.

Loosen the clevis lock nut.


iii.

Adjust the brake pedal height by turning the push rod.

Brake Pedal Height from Dash Panel Insulator Assembly Clip:

173.5 to 185.5 mm (6.83 to 7.30 in.)



iv.

Tighten the clevis lock nut.

Torque:
for TMC Made : 26 N*m (265 kgf*cm, 19 ft.*lbf)
for TMMT Made : 22 N*m (224 kgf*cm, 16 ft.*lbf)


v.

Install the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



d.

Install the No. 1 air duct.

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION



Hide 2.INSPECT BRAKE PEDAL FREE PLAY

a.
C132708C04
2.177,1.542 2.781,1.885 0.604,0.344 10 *a
*a Brake Pedal Free Play


Depress the brake pedal until a slight resistance is felt. Measure the brake pedal free play as shown in the illustration.

Brake Pedal Free Play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the pedal free play is not as specified, check the stop light switch clearance.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSTALLATION

If the pedal free play is as specified, proceed to the Inspect Brake Pedal Reserve Distance procedure.


Hide 3.INSPECT BRAKE PEDAL RESERVE DISTANCE

a.

Remove the front door scuff plate RH.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL



b.

Remove the cowl side trim board RH.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL



c.

Remove the No. 1 instrument panel under cover sub-assembly.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL



d.

Remove the console box insert.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>REMOVAL



e.

Turn back the front floor carpet assembly.


f.

With the engine running, depress the brake pedal and measure the brake pedal reserve distance as shown in the illustration.

C425073C01
2.302,0.833 2.417,0.25 2.417,0.25 2.583,0.25 true 2.823,1.021 3.135,0.948 true 6.052,1.125 6.375,0.99 true 4.479,1.177 4.76,1.344 true 1.854,0.427 2.094,0.646 0.24,0.219 10 true *a 2.604,0.177 2.844,0.396 0.24,0.219 10 true *b 1.938,1.469 2.177,1.688 0.24,0.219 10 true *c 3.156,0.844 3.396,1.063 0.24,0.219 10 true *1 5.615,2.031 5.854,2.25 0.24,0.219 10 true *a 4.302,1.063 4.542,1.281 0.24,0.219 10 true *2 6.396,0.896 6.635,1.115 0.24,0.219 10 true *1
*1 Brake Pedal Pad *2 Column Hole Cover Silencer Sheet
*a Brake Pedal Reserve Distance *b Measuring Plane of Column Hole Cover Silencer Sheet
*c 100 mm (3.94 in.) - -


Brake Pedal Reserve Distance from Column Hole Cover Silencer Sheet at 300 N (31 kgf, 67.4 lbf):

119.0 mm (4.69 in.) or more


If the distance is not as specified, troubleshoot the brake system.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE


g.

Install the front floor carpet assembly to its original position.


h.

Install the console box insert.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION



i.

Install the No. 1 instrument panel under cover sub-assembly.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION



j.

Install the cowl side trim board RH.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION



k.

Install the front door scuff plate RH.

HINT:

Use the same procedure for LHD vehicles.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>REAR CONSOLE BOX>INSTALLATION