Home › Brake › BRAKE (REAR) › REAR BRAKE (for TMC Made) › from 2019.09
RM32H0E _54 Brake _060042 BRAKE (REAR) _0358314 REAR BRAKE(for TMC Made) A

BRAKE (REAR)  REAR BRAKE(for TMC Made)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Immediately after installing the brake pads, the braking performance may be reduced. Always perform a road test in a safe place while paying attention to the surroundings.

·

After replacing the rear disc brake pads, the brake pedal may feel soft due to clearance between the rear disc brake pads and rear disc. Depress the brake pedal several times until the brake pedal feels firm.

·

After replacing the rear disc brake pads, always perform a road test to check the braking performance and check for vibrations.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 42431 1.INSTALL REAR DISC

a.
C366010C03
0.99,1.927 1.51,1.5 true 0.979,1.927 1.49,1.448 true 0.823,1.854 1.135,2.01 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks of the rear disc and rear axle hub and bearing assembly, and install the rear disc.

NOTICE:

When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.



Hide 2.INSTALL REAR DISC BRAKE CYLINDER MOUNTING

a.

Install the rear disc brake cylinder mounting to the rear axle carrier sub-assembly with the 2 bolts.

Torque:
107 N*m (1091 kgf*cm, 79 ft.*lbf)


Hide 3.INSTALL REAR DISC BRAKE BUSHING DUST BOOT

a.
C366014C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the entire circumference of 2 new rear disc brake bushing dust boots.

HINT:

Apply more than 0.3 g (0.01 oz.) of lithium soap base glycol grease to each rear disc brake bushing dust boot.



b.

Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


Hide 4.INSTALL REAR DISC BRAKE CYLINDER SLIDE PIN

a.
C366015C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the contact surface of the rear No. 2 disc brake cylinder slide pin.


b.

Install a new rear disc brake cylinder slide bushing to the rear No. 2 disc brake cylinder slide pin.


c.
C366016C01
0,0 0,0 false
V100155

Lithium Soap Base Glycol Grease


Apply a light layer of lithium soap base glycol grease to the sliding part and the sealing surfaces of the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin.


d.
C366006C03
1.792,0.313 2.125,0.313 true 1.583,1.052 1.917,1.052 true 1.958,0.979 2.167,1.156 0.208,0.177 10 true *1 2.167,0.229 2.365,0.417 0.198,0.188 10 true *2
*1 Rear No. 1 Disc Brake Cylinder Slide Pin
*2 Rear No. 2 Disc Brake Cylinder Slide Pin


Install the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin to the rear disc brake cylinder mounting.


e.

Push the rear No. 1 disc brake cylinder slide pin and rear No. 2 disc brake cylinder slide pin into each rear disc brake bushing dust boot to engage the pins to the boots.


Hide 5.INSTALL REAR DISC BRAKE PAD SUPPORT PLATE

a.

Install the 4 rear disc brake pad support plates to the rear disc brake cylinder mounting.

NOTICE:

Be sure to install each rear disc brake pad support plate in the correct position and direction.



Hide 6.INSTALL REAR DISC BRAKE ANTI-SQUEAL SHIM

Hide 7.INSTALL REAR DISC BRAKE PAD

a.

Install the 2 rear disc brake pads to the rear disc brake cylinder mounting.

NOTICE:
·

Keep the friction surfaces of the rear disc brake pads and rear disc free from oil and grease.

·

Install the rear disc brake pad so that the rear disc brake pad wear indicator plate is mounted on the lower side of the vehicle.



HINT:
C418241C01
0.781,1.073 1.313,1.073 true 2.344,0.823 2.76,0.823 true 2.875,0.729 3.188,0.885 0.313,0.156 10 false *a 0.552,0.979 0.865,1.135 0.313,0.156 10 false *b
*a Inner Side (Orange)
*b Outer Side (Yellow green)


If the rear disc brake pad has an identification mark, be sure to confirm the installation location.



Hide 8.INSTALL REAR DISC BRAKE CYLINDER ASSEMBLY

a.
C422653C01
1.042,2.542 1.354,2.698 0.313,0.156 10 false *a 1.771,2.396 2.083,2.552 0.313,0.156 10 false *b 1.958,1.552 2.115,1.75 0.156,0.198 10 true 1 2.354,0.271 2.51,0.469 0.156,0.198 10 true 2
*a Hold
*b Turn


Hold the 2 rear disc brake cylinder slide pins, and install the rear disc brake cylinder assembly to the rear disc brake cylinder mounting with 2 new bolts in the order shown in the illustration.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


Hide 46310B 9.INSTALL PARKING BRAKE ACTUATOR ASSEMBLY

a.

Apply a light coat of lithium soap base glycol grease to a new O-ring.


b.

Install the O-ring to the rear disc brake cylinder assembly.

NOTICE:

Make sure to replace the O-ring with a new one when installing the parking brake actuator assembly.



c.

Using a 5 mm hexagon socket wrench, install the parking brake actuator assembly to the rear disc brake cylinder assembly with the 2 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 890C0A 10.CONNECT NO. 2 PARKING BRAKE WIRE ASSEMBLY

a.

Connect the No. 2 parking brake wire assembly to the parking brake actuator assembly.


Hide 47319F 11.CONNECT REAR FLEXIBLE HOSE

a.

Connect the rear flexible hose to the rear disc brake cylinder assembly with a new union bolt and a new gasket.

Torque:
30.4 N*m (310 kgf*cm, 22 ft.*lbf)

NOTICE:

Install the rear flexible hose lock securely into the lock hole in the rear disc brake cylinder assembly.



Hide 12. BLEED BRAKE LINE

Hide 13.BLEED REAR DISC BRAKE CYLINDER ASSEMBLY

CAUTION:

If the rear disc brake cylinder assembly has been disassembled, perform air bleeding for the rear disc brake cylinder.


NOTICE:
·

Perform air bleeding while maintaining the brake fluid level between the MAX and MIN lines on the brake fluid reservoir.

·

Do not allow brake fluid to contact any painted surface. If brake fluid leaks onto any painted surface, immediately wash it off.



HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.

·

While performing air bleeding of the rear disc brake assembly, the bolt can be reused during the bleeding procedure. After air bleeding is complete, replace the bolt with a new one.



a.

Perform the procedure to enter rear disc brake pad replacement mode 5 times.

Click hereBrake>PARKING BRAKE>ELECTRIC PARKING BRAKE SYSTEM>TEST MODE PROCEDURE


b.

Release the parking brake.


c.
C366000

Disconnect the No. 2 parking brake wire assembly from the parking brake actuator assembly.

NOTICE:
·

Remove any dirt or foreign matter on and around the connector before performing this work.

·

Do not allow water, oil or dirt to enter the No. 2 parking brake wire assembly connector.




d.

Remove the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID>REPLACEMENT


e.

Remove the brake master cylinder reservoir filler cap.


f.

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.

NOTICE:
·

Make sure that there is sufficient brake fluid in the reservoir.

·

If brake fluid leaks onto any painted surface, immediately wash it off.

·

Do not remove the filter from the brake master cylinder reservoir and be sure to fill the brake master cylinder reservoir with new brake fluid to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.




g.
C422685C01
1.677,2.729 1.99,2.885 0.313,0.156 10 false *a 0.896,2.875 1.208,3.031 0.313,0.156 10 false *b
*a Turn
*b Hold


Hold the 2 rear disc brake cylinder slide pins and remove the 2 bolts and separate the rear disc brake cylinder assembly from the rear disc brake cylinder mounting (*1).


h.
C422655

Hold the rear disc brake cylinder assembly horizontally, then tilt it 45° toward the bleeder plug side as shown in the illustration.(*2)


i.
C422686C01
1.813,2.365 2.125,2.563 0.313,0.198 10 false *a 1.073,2.531 1.385,2.729 0.313,0.198 10 false *b
*a Turn
*b Hold


Temporarily install the rear disc brake cylinder assembly with the 2 bolts.(*3)


j.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.(*4)


k.

When fluid stops coming out, tighten the bleeder plug and release the brake pedal.(*5)


l.

Repeat steps (*1) through (*5) 3 times.

NOTICE:

If there is still air in the system after performing steps (*1) through (*5) 3 times, repeat the steps (*1) through (*5) until the air has been bled.



m.

Tighten the bleeder plug completely.

Torque:
8.3 N*m (85 kgf*cm, 73 in.*lbf)


n.

Install the rear disc brake cylinder assembly with 2 new bolts.

Torque:
34.3 N*m (350 kgf*cm, 25 ft.*lbf)


o.

Connect the No. 2 parking brake wire assembly connector to the parking brake actuator assembly.


p.

Inspect for brake fluid leaks.


q.

Inspect the brake fluid level in the reservoir.

Click hereBrake>BRAKE SYSTEM (OTHER)>BRAKE FLUID>ON-VEHICLE INSPECTION


r.

Install the brake master cylinder reservoir filler cap assembly.


s.

Install the center No. 1 cowl top ventilator louver.

Click hereGeneral>MAINTENANCE>BRAKE FLUID>REPLACEMENT


Hide 14.INSTALL REAR WHEEL