Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2019.09
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294190 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1660  P Seat Airbag Active Mode Indicator  


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator (clock assembly).

The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger without door airbag assembly.

DTC B1660 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Test Mode / Check Mode
B1660 P Seat Airbag Active Mode Indicator Any of the following conditions is met:
·

The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit.

·

The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit.

·

Passenger airbag ON/OFF indicator malfunction

·

Airbag sensor assembly malfunction


·

Instrument panel wire

·

Instrument panel junction block assembly

·

Passenger airbag ON/OFF indicator (Clock assembly)

·

Airbag sensor assembly


Does not apply to test/check mode

DTC Detection Conditions:
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Ignition switch ON ○ ○ ○ ○ ○ ○
Malfunction Status The airbag sensor assembly detects a line short in the passenger airbag ON/OFF indicator circuit ○ - - - - -
The airbag sensor assembly detects a short to ground in the passenger airbag ON/OFF indicator circuit - ○ - - - -
The airbag sensor assembly detects a short to B+ in the passenger airbag ON/OFF indicator circuit - - ○ - - -
The airbag sensor assembly detects an open in the passenger airbag ON/OFF indicator circuit - - - ○ - -
Passenger airbag ON/OFF indicator malfunction - - - - ○ -
Airbag sensor assembly malfunction - - - - - ○
Detection Time - - - - - -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

B474761E13
3.458,1.49 3.823,1.75 0.365,0.26 10 false 3A 3.458,1.656 4.542,2.354 1.083,0.698 10 false Instrument Panel Junction Block Assembly 5.188,0.469 5.552,0.729 0.365,0.26 10 false 35 5.188,1.156 5.552,1.417 0.365,0.26 10 false 34 5.188,2.313 5.552,2.573 0.365,0.26 10 false 33 5.188,2.625 5.552,2.885 0.365,0.26 10 false 32 5.417,2.625 5.781,2.885 0.365,0.26 10 false E2 5.417,2.313 5.781,2.573 0.365,0.26 10 false E1 5.375,3.313 7.031,3.656 1.656,0.344 10 false Airbag Sensor Assembly 5.375,3.146 5.771,3.344 0.396,0.198 10 false F150 5.427,0.469 6.01,0.729 0.583,0.26 10 false PAON 5.427,1.167 6.01,1.427 0.583,0.26 10 false P-AB 4.771,0.469 5.135,0.729 0.365,0.26 10 false 8 4.771,1.156 5.115,1.417 0.344,0.26 10 false 46 3.26,1.156 3.698,1.417 0.438,0.26 10 false 51 3.26,0.469 3.625,0.729 0.365,0.26 10 false 29 2.365,0.563 2.948,0.823 0.583,0.26 10 false PAON 2.438,1.26 3.021,1.521 0.583,0.26 10 false P-AB 2.844,0.469 3.208,0.729 0.365,0.26 10 false 4 2.844,1.156 3.208,1.417 0.365,0.26 10 false 3 1.896,1.635 2.271,1.813 0.375,0.177 10 false F81 1.885,1.823 3.021,2.885 1.135,1.063 10 false Passenger Airbag ON/OFF Indicator (Clock Assembly) 0.688,1.01 1.792,1.219 1.104,0.208 10 false ECU-IG1 NO. 4 2.115,0.885 2.49,1.083 0.375,0.198 10 false IG+ 0.083,0.198 1.615,0.427 1.531,0.229 10 false from IG1-NO. 1 Relay 1.927,0.75 2.115,0.927 0.188,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Turn the ignition switch to ON.


b.

Check the passenger airbag ON/OFF indicator operation.

HINT:

Refer to the normal condition of the passenger airbag ON/OFF indicator.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM



Result:
Result Proceed to
Passenger airbag ON/OFF indicator illumination is always on. A
Passenger airbag ON/OFF indicator illumination is always off. B



A

2.CHECK CONNECTORS

B

13.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Turn the ignition switch to ON.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION
a.

Connect the connector to the passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator operation.

OK:

The passenger airbag ON/OFF indicator does not come on.



Result:
Proceed to
OK
NG



OK

4.CHECK DTC

NG

5.CHECK WIRE HARNESS (OPEN)
4.CHECK DTC
a.
C284134C05
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the airbag sensor assembly.


d.

Connect the cable to the negative (-) battery terminal.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

5.CHECK WIRE HARNESS (OPEN)
a.

Turn the ignition switch off.

C398658C02
2.271,3.833 2.688,4.063 0.417,0.229 2.448,0.906 2.875,1.146 0.427,0.24 3.052,1.615 3.74,1.302 true 4.25,1.594 3.823,1.302 true 4.083,4.333 3.396,4.031 true 2.667,4.333 3.208,4.031 true 3.625,1.781 3.792,1.781 3.792,1.781 3.792,1.656 true 3.667,3.167 3.667,2.552 true 3.448,2.833 3.667,2.833 true 2.219,2.469 2.406,2.75 0.188,0.281 10 false *1 2.219,3.021 2.417,3.302 0.198,0.281 10 false *3 4.563,2.479 4.792,2.792 0.229,0.313 10 false *2 3.604,3.198 3.938,3.448 0.333,0.25 10 false *4 3.406,1.708 3.625,2 0.219,0.292 10 false *c 2.417,0.198 2.677,0.5 0.26,0.302 10 false *a 2.25,3.542 2.51,3.792 0.26,0.25 10 false *b 2.354,3.854 2.688,4.125 0.333,0.271 10 false F81 2.5,0.948 2.844,1.156 0.344,0.208 10 false F150 4.292,2.469 4.5,2.75 0.208,0.281 10 false A 3.99,2.469 4.198,2.75 0.208,0.281 10 false B 2.615,2.469 2.823,2.75 0.208,0.281 10 false C 2.458,2.469 2.615,2.75 0.156,0.281 10 false D 2.76,3.021 2.906,3.281 0.146,0.26 10 false E 2.458,3.021 2.615,3.302 0.156,0.281 10 false F 2.667,1.615 3.063,1.865 0.396,0.25 10 false P-AB 4.156,1.625 4.625,1.927 0.469,0.302 10 false PAON 4.073,4.344 4.521,4.656 0.448,0.313 10 false PAON 2.313,4.333 2.729,4.583 0.417,0.25 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))
*c Service Wire - -



b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Disconnect the connector from the passenger airbag ON/OFF indicator (clock assembly).


d.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK WIRE HARNESS (SHORT)

NG

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
6.CHECK WIRE HARNESS (SHORT)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK WIRE HARNESS (SHORT TO B+)

NG

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
7.CHECK WIRE HARNESS (SHORT TO B+)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-4 (PAON) - Body ground Ignition switch ON Below 1 V
F81-3 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

8.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
8.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - Body ground Always 1 MΩ or higher
F81-3 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE PASSENGER AIRBAG ON/OFF INDICATOR (CLOCK ASSEMBLY)

NG

9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
9.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

10.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-8 (PAON) - Body ground Ignition switch ON Below 1 V
3A-29 (PAON) - Body ground Ignition switch ON Below 1 V
3A-46 (P-AB) - Body ground Ignition switch ON Below 1 V
3A-51 (P-AB) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

11.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

12.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Disconnect the connector from the instrument panel junction block assembly.

C398660C02
2.75,3.25 3.177,3.5 0.427,0.25 3.167,0.208 3.563,0.448 0.396,0.24 3.635,0.75 4.052,0.375 true 3.563,1.042 3.979,1.375 true 3.229,3.667 4.021,3.969 true 4.448,3.698 4.125,3.969 true 4.333,4.448 4.083,4.448 4.083,4.448 4.083,4.333 true 3.583,2.51 3.583,2.063 true 3.406,2.333 3.573,2.333 true 2.167,2 2.385,2.271 0.219,0.271 10 false *1 2.167,2.479 2.385,2.75 0.219,0.271 10 false *3 4.5,1.979 4.719,2.25 0.219,0.271 10 false *2 3.521,2.542 3.771,2.76 0.25,0.219 10 false *4 4.25,1.979 4.417,2.25 0.167,0.271 10 false A 2.198,0.208 2.479,0.458 0.281,0.25 10 false *a 2.698,2.896 2.948,3.167 0.25,0.271 10 false *b 3.281,0.24 3.583,0.49 0.302,0.25 10 false 3A 2.802,3.292 3.167,3.521 0.365,0.229 10 false F150 2.833,3.583 3.198,3.938 0.365,0.354 10 false P-AB 4.396,4.375 4.729,4.625 0.333,0.25 10 false *c 4.479,3.625 4.917,4 0.438,0.375 10 false PAON 3.948,1.979 4.115,2.25 0.167,0.271 10 false B 2.719,1.979 2.885,2.25 0.167,0.271 10 false C 2.417,1.979 2.583,2.25 0.167,0.271 10 false D 2.719,2.479 2.885,2.75 0.167,0.271 10 false E 2.417,2.479 2.583,2.75 0.167,0.271 10 false F 4.125,0.292 4.604,0.573 0.479,0.281 10 false PAON 4.052,1.302 4.542,1.573 0.49,0.271 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)
*c Service Wire - -


HINT:

The service wire has already been inserted into connector B.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.

Using a service wire, connect terminals 3 (P-AB) and 4 (PAON) of connector E.

C398661C02
2.25,3.573 2.646,3.823 0.396,0.25 3.281,0.208 3.667,0.448 0.385,0.24 3.667,2.833 3.667,2.208 true 3.448,2.5 3.667,2.5 true 4.292,0.375 4.125,0.896 true 4.406,1.365 4.219,1.073 true 2.698,4.198 3.167,3.771 true 3.99,4.208 3.333,3.771 true 3.583,4.427 3.25,4.427 3.25,4.427 3.25,4.344 true 2.229,2.125 2.458,2.396 0.229,0.271 10 false *1 2.229,2.615 2.448,2.906 0.219,0.292 10 false *3 4.531,2.125 4.792,2.417 0.26,0.292 10 false *2 3.594,2.875 3.833,3.167 0.24,0.292 10 false *4 2.271,0.188 2.604,0.427 0.333,0.24 10 false *a 2.281,3.292 2.563,3.531 0.281,0.24 10 false *b 4.292,2.125 4.5,2.333 0.208,0.208 10 false A 3.385,0.24 3.708,0.469 0.323,0.229 10 false 3A 2.333,3.615 2.667,3.896 0.333,0.281 10 false F81 2.313,4.135 2.688,4.458 0.375,0.323 10 false P-AB 4.052,4.135 4.5,4.5 0.448,0.365 10 false PAON 3.625,4.333 3.917,4.583 0.292,0.25 10 false *c 3.99,2.125 4.198,2.333 0.208,0.208 10 false B 2.76,2.125 2.969,2.333 0.208,0.208 10 false C 2.458,2.125 2.667,2.333 0.208,0.208 10 false D 2.76,2.625 2.969,2.833 0.208,0.208 10 false E 2.458,2.625 2.667,2.833 0.208,0.208 10 false F 4.323,0.271 4.844,0.521 0.521,0.25 10 false PAON 4.292,1.385 4.75,1.646 0.458,0.26 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))
*c Service Wire - -


NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

13.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the airbag sensor assembly, passenger airbag ON/OFF indicator (clock assembly) and instrument panel junction block assembly.


e.

Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.



Result:
Proceed to
OK
NG



OK

14.CHECK WIRE HARNESS (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

14.CHECK WIRE HARNESS (OPEN)
a.

Connect the connector to the instrument panel junction block assembly.

C398658C02
2.271,3.833 2.688,4.063 0.417,0.229 2.448,0.906 2.875,1.146 0.427,0.24 3.052,1.615 3.74,1.302 true 4.25,1.594 3.823,1.302 true 4.083,4.333 3.396,4.031 true 2.667,4.333 3.208,4.031 true 3.625,1.781 3.792,1.781 3.792,1.781 3.792,1.656 true 3.667,3.167 3.667,2.552 true 3.448,2.833 3.667,2.833 true 2.219,2.469 2.406,2.75 0.188,0.281 10 false *1 2.219,3.021 2.417,3.302 0.198,0.281 10 false *3 4.563,2.479 4.792,2.792 0.229,0.313 10 false *2 3.604,3.198 3.938,3.448 0.333,0.25 10 false *4 3.406,1.708 3.625,2 0.219,0.292 10 false *c 2.417,0.198 2.677,0.5 0.26,0.302 10 false *a 2.25,3.542 2.51,3.792 0.26,0.25 10 false *b 2.354,3.854 2.688,4.125 0.333,0.271 10 false F81 2.5,0.948 2.844,1.156 0.344,0.208 10 false F150 4.292,2.469 4.5,2.75 0.208,0.281 10 false A 3.99,2.469 4.198,2.75 0.208,0.281 10 false B 2.615,2.469 2.823,2.75 0.208,0.281 10 false C 2.458,2.469 2.615,2.75 0.156,0.281 10 false D 2.76,3.021 2.906,3.281 0.146,0.26 10 false E 2.458,3.021 2.615,3.302 0.156,0.281 10 false F 2.667,1.615 3.063,1.865 0.396,0.25 10 false P-AB 4.156,1.625 4.625,1.927 0.469,0.302 10 false PAON 4.073,4.344 4.521,4.656 0.448,0.313 10 false PAON 2.313,4.333 2.729,4.583 0.417,0.25 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))
*c Service Wire - -



b.

Using a service wire, connect terminals 35 (PAON) and 34 (P-AB) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK WIRE HARNESS (SHORT)

NG

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
15.CHECK WIRE HARNESS (SHORT)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Disconnect the service wire from connector B.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - F81-3 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK WIRE HARNESS (SHORT TO B+)

NG

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
16.CHECK WIRE HARNESS (SHORT TO B+)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-4 (PAON) - Body ground Ignition switch ON Below 1 V
F81-3 (P-AB) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

17.CHECK WIRE HARNESS (SHORT TO GROUND)

NG

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
17.CHECK WIRE HARNESS (SHORT TO GROUND)
a.
C398659C01
0.167,2.281 0.583,2.563 0.417,0.281 1.302,2.469 0.667,2.917 true 1.448,2.458 2.302,2.896 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.302,2.917 0.75,3.25 0.448,0.333 10 false P-AB 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 2.333,2.917 2.792,3.229 0.458,0.313 10 false PAON
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F81-4 (PAON) - Body ground Always 1 MΩ or higher
F81-3 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
18.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)
a.
C398659C02
0.167,2.281 0.583,2.563 0.417,0.281 1,2.458 0.5,2.917 true 1.833,0.635 1.833,1.417 true 1.625,1.083 1.833,1.083 true 0.135,0.552 0.333,0.833 0.198,0.281 10 false *1 0.135,1.219 0.365,1.5 0.229,0.281 10 false *3 3,0.552 3.25,0.833 0.25,0.281 10 false *2 0.167,1.885 0.427,2.167 0.26,0.281 10 false *a 2.667,0.552 2.865,0.833 0.198,0.281 10 false A 0.25,2.333 0.604,2.604 0.354,0.271 10 false F81 2.292,0.552 2.49,0.833 0.198,0.281 10 false B 0.604,0.552 0.802,0.833 0.198,0.281 10 false C 0.417,0.552 0.615,0.833 0.198,0.281 10 false D 0.792,1.229 0.99,1.51 0.198,0.281 10 false E 0.417,1.229 0.615,1.51 0.198,0.281 10 false F 1.771,1.458 2.083,1.74 0.313,0.281 10 false *4 0.302,2.927 0.604,3.24 0.302,0.313 10 false IG+
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))


Connect the cable to the negative (-) battery terminal.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F81-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR

NG

REPLACE WIRE HARNESS OR BATTERY

19.CHECK PASSENGER AIRBAG ON/OFF INDICATOR
a.
B474767C12
0.667,1.917 1.083,2.167 0.417,0.25 2.167,2.885 2.552,2.615 true 2.083,2.885 1.229,2.604 true 1.75,1.135 1.75,0.552 false 1.5,0.833 1.75,0.833 false 0.26,0.458 0.698,0.823 0.438,0.365 10 false *1 2.854,0.469 3.229,0.781 0.375,0.313 10 false *2 0.271,1.021 0.698,1.49 0.427,0.469 10 false *3 1.677,1.156 2.073,1.49 0.396,0.333 10 false *4 0.469,1.552 0.917,2.146 0.448,0.594 10 false *a 0.729,1.948 1.104,2.177 0.375,0.229 10 false F150 2.594,2.531 3.135,3 0.542,0.469 10 false PAON 0.875,2.531 1.417,3 0.542,0.469 10 false P-AB 2.573,0.469 2.948,0.781 0.375,0.313 10 false A 2.198,0.469 2.573,0.781 0.375,0.313 10 false B 0.698,0.469 1.073,0.781 0.375,0.313 10 false C 0.5,0.469 0.875,0.781 0.375,0.313 10 false D 0.698,1.021 1.073,1.333 0.375,0.313 10 false E 0.5,1.021 0.875,1.333 0.375,0.313 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Connect the connector to the passenger airbag ON/OFF indicator (clock assembly).


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Check the passenger airbag ON/OFF indicator according to the conditions in the table below.

OK:
Terminal Connection Switch Condition Specified Condition
F150-35 (PAON) - Body ground Ignition switch ON "ON" comes on
F150-34 (P-AB) - Body ground Ignition switch ON "OFF" comes on



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

20.CHECK DTC

NG

REPLACE PASSENGER AIRBAG ON/OFF INDICATOR (CLOCK ASSEMBLY)

20.CHECK DTC
a.
C284134C05
0.271,0.802 0.583,1.073 0.313,0.271 10 false *1 2.906,0.813 3.219,1.104 0.313,0.292 10 false *2 0.292,1.469 0.719,1.917 0.427,0.448 10 false *3 2.615,0.802 2.927,1.146 0.313,0.344 10 false A 2.427,0.802 2.74,1.198 0.313,0.396 10 false B 0.74,0.802 1.042,1.177 0.302,0.375 10 false C 0.552,0.802 0.865,1.094 0.313,0.292 10 false D 0.729,1.479 1.083,1.979 0.354,0.5 10 false E 0.563,1.479 0.875,1.635 0.313,0.156 10 false F
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly)


Connect the connector to the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1660 is not output.


HINT:

Codes other than DTC B1660 may be output at this time, but they are not related to this check.



Result:
Proceed to
OK
NG



OK

NG

21.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - Body ground Always 1 MΩ or higher
3A-29 (PAON) - Body ground Always 1 MΩ or higher
3A-46 (P-AB) - Body ground Always 1 MΩ or higher
3A-51 (P-AB) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

22.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Connect the cable to the negative (-) battery terminal.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3A-8 (PAON) - Body ground Ignition switch ON Below 1 V
3A-29 (PAON) - Body ground Ignition switch ON Below 1 V
3A-46 (P-AB) - Body ground Ignition switch ON Below 1 V
3A-51 (P-AB) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

23.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
C285472C08
1.646,0.198 1.979,0.448 0.333,0.25 1.333,0.333 1.885,0.792 true 2.688,0.333 2.469,0.927 true 1.969,3.188 1.969,2.438 false 1.969,2.75 1.635,2.75 false 2.833,1.583 2.573,1.125 true 1.583,1.583 1.823,1.146 true 0.208,2.375 0.625,2.708 0.417,0.333 10 false *1 3,2.385 3.25,2.813 0.25,0.427 10 false *2 0.208,2.979 0.542,3.25 0.333,0.271 10 false *3 1.906,3.208 2.156,3.406 0.25,0.198 10 false *4 0.156,0.198 0.573,0.49 0.417,0.292 10 false *a 1.729,0.25 2.146,0.583 0.417,0.333 10 false 3A 0.906,0.25 1.333,0.531 0.427,0.281 10 false PAON 2.75,0.25 3.25,0.5 0.5,0.25 10 false PAON 2.708,2.375 2.958,2.802 0.25,0.427 10 false A 2.333,2.375 2.583,2.802 0.25,0.427 10 false B 0.823,2.375 1.073,2.802 0.25,0.427 10 false C 0.458,2.375 0.708,2.802 0.25,0.427 10 false D 0.823,2.969 1.073,3.396 0.25,0.427 10 false E 0.458,2.969 0.708,3.396 0.25,0.427 10 false F 2.917,1.5 3.333,1.75 0.417,0.25 10 false P-AB 1.188,1.5 1.563,1.833 0.375,0.333 10 false P-AB
*1 Instrument Panel Junction Block Assembly
*2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator
(Clock Assembly)
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)


Disconnect the connector from the instrument panel junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always 1 MΩ or higher
3A-29 (PAON) - 3A-51 (P-AB) Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

24.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.

Disconnect the connector from the instrument panel junction block assembly.

HINT:

The service wire has already been inserted into connector B.


C398660C02
2.75,3.25 3.177,3.5 0.427,0.25 3.167,0.208 3.563,0.448 0.396,0.24 3.635,0.75 4.052,0.375 true 3.563,1.042 3.979,1.375 true 3.229,3.667 4.021,3.969 true 4.448,3.698 4.125,3.969 true 4.333,4.448 4.083,4.448 4.083,4.448 4.083,4.333 true 3.583,2.51 3.583,2.063 true 3.406,2.333 3.573,2.333 true 2.167,2 2.385,2.271 0.219,0.271 10 false *1 2.167,2.479 2.385,2.75 0.219,0.271 10 false *3 4.5,1.979 4.719,2.25 0.219,0.271 10 false *2 3.521,2.542 3.771,2.76 0.25,0.219 10 false *4 4.25,1.979 4.417,2.25 0.167,0.271 10 false A 2.198,0.208 2.479,0.458 0.281,0.25 10 false *a 2.698,2.896 2.948,3.167 0.25,0.271 10 false *b 3.281,0.24 3.583,0.49 0.302,0.25 10 false 3A 2.802,3.292 3.167,3.521 0.365,0.229 10 false F150 2.833,3.583 3.198,3.938 0.365,0.354 10 false P-AB 4.396,4.375 4.729,4.625 0.333,0.25 10 false *c 4.479,3.625 4.917,4 0.438,0.375 10 false PAON 3.948,1.979 4.115,2.25 0.167,0.271 10 false B 2.719,1.979 2.885,2.25 0.167,0.271 10 false C 2.417,1.979 2.583,2.25 0.167,0.271 10 false D 2.719,2.479 2.885,2.75 0.167,0.271 10 false E 2.417,2.479 2.583,2.75 0.167,0.271 10 false F 4.125,0.292 4.604,0.573 0.479,0.281 10 false PAON 4.052,1.302 4.542,1.573 0.49,0.271 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Airbag Sensor Assembly)
*c Service Wire - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-8 (PAON) - 3A-46 (P-AB) Always Below 1 Ω



c.

Disconnect the service wire from connector B.


d.

Using a service wire, connect terminals 3 (P-AB) and 4 (PAON) of connector E.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.


C398661C02
2.25,3.573 2.646,3.823 0.396,0.25 3.281,0.208 3.667,0.448 0.385,0.24 3.667,2.833 3.667,2.208 true 3.448,2.5 3.667,2.5 true 4.292,0.375 4.125,0.896 true 4.406,1.365 4.219,1.073 true 2.698,4.198 3.167,3.771 true 3.99,4.208 3.333,3.771 true 3.583,4.427 3.25,4.427 3.25,4.427 3.25,4.344 true 2.229,2.125 2.458,2.396 0.229,0.271 10 false *1 2.229,2.615 2.448,2.906 0.219,0.292 10 false *3 4.531,2.125 4.792,2.417 0.26,0.292 10 false *2 3.594,2.875 3.833,3.167 0.24,0.292 10 false *4 2.271,0.188 2.604,0.427 0.333,0.24 10 false *a 2.281,3.292 2.563,3.531 0.281,0.24 10 false *b 4.292,2.125 4.5,2.333 0.208,0.208 10 false A 3.385,0.24 3.708,0.469 0.323,0.229 10 false 3A 2.333,3.615 2.667,3.896 0.333,0.281 10 false F81 2.313,4.135 2.688,4.458 0.375,0.323 10 false P-AB 4.052,4.135 4.5,4.5 0.448,0.365 10 false PAON 3.625,4.333 3.917,4.583 0.292,0.25 10 false *c 3.99,2.125 4.198,2.333 0.208,0.208 10 false B 2.76,2.125 2.969,2.333 0.208,0.208 10 false C 2.458,2.125 2.667,2.333 0.208,0.208 10 false D 2.76,2.625 2.969,2.833 0.208,0.208 10 false E 2.458,2.625 2.667,2.833 0.208,0.208 10 false F 4.323,0.271 4.844,0.521 0.521,0.25 10 false PAON 4.292,1.385 4.75,1.646 0.458,0.26 10 false P-AB
*1 Instrument Panel Junction Block Assembly *2 Airbag Sensor Assembly
*3 Passenger Airbag ON/OFF Indicator (Clock Assembly) *4 Instrument Panel Wire
*a Front view of wire harness connector
(to Instrument Panel Junction Block Assembly)
*b Front view of wire harness connector
(to Passenger Airbag ON/OFF Indicator (Clock Assembly))
*c Service Wire - -



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3A-29 (PAON) - 3A-51 (P-AB) Always Below 1 Ω



f.

Disconnect the service wire from connector E.


Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE