If the key ID codes of the key and transponder key ECU assembly match, the immobiliser system is unset and the engine start permission signal is sent to the ECM. When the ID codes of the transponder key ECU assembly and ECM match, the engine starts.
If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.
Clear the DTCs.
for 8NR-FTS:
for 3ZR-FAE:
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
for 8NR-FTS:
for 3ZR-FAE:
DTC is not output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Engine / Active Test.
Perform the Active Test according to the display on the GTS.
for 8NR-FTS:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut Status | Status of immobiliser system fuel cut | OFF/ON | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut Status |
for 3ZR-FAE:
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Immobiliser Fuel Cut | Status of immobiliser system fuel cut | OFF/ON | - | - |
| Tester Display |
|---|
| Immobiliser Fuel Cut |
OFF is displayed after the engine is started.
| Result | Proceed to |
|---|---|
| OK (for 3ZR-FAE) | A |
| OK (for 8NR-FTS) | B |
| NG | C |
A
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A38-28 (IMI) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Ignition switch ON |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform not output, or has abnormal wavelength or shape | B |
A
B
Using an oscilloscope, check the waveform
| *a | Component with harness connected
(ECM) |
*b | Waveform |
| Item | Content |
|---|---|
| Tester Connection | A38-45 (IMO) - Body ground |
| Tool Setting | 2 V/DIV., 500 ms./DIV. |
| Condition | Within 3 seconds of the ignition switch first being turned to ON after cable is disconnected and reconnected to the negative (-) battery terminal |
| Result | Proceed to |
|---|---|
| Normal waveform | A |
| Waveform not output, or has abnormal wavelength or shape (for 3ZR-FAE) | B |
| Waveform not output, or has abnormal wavelength or shape (for 8NR-FTS) | C |
A
B
C
Register the communication ID between the transponder key ECU assembly and ECM.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| Engine can be started | A |
| Engine cannot be started | B |
A
B
Replace the transponder key ECU assembly with a new one.
Refer to Service Bulletin.
Key ID code registration is necessary when replacing the transponder key ECU assembly.
Refer to Service Bulletin.
| Proceed to |
|---|
| NEXT |
NEXT
Using a registered key, turn the ignition switch to ON.
Check that the engine starts 5 seconds after the ignition switch was turned to ON.
Engine starts normally.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for 3ZR-FAE) | B |
| NG (for 8NR-FTS) | C |
A
B
Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C
Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the F22*1, F137*2 transponder key ECU assembly connector
Disconnect the A38 ECM connector
Measure the resistance according to the value(s) in the table below
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| F22-13 (EFIO) - A38-28 (IMI)*1
F137-11 (EFIO) - A38-28 (IMI)*2 |
Always | Below 1 Ω |
| F22-13 (EFIO) - Body ground*1
F137-11 (EFIO) - Body ground*2 |
Always | 10 kΩ or higher |
| A38-28 (IMI) - Body ground | Always | 10 kΩ or higher |
*1: for 16 Pin Type
*2: for 12 Pin Type
| Proceed to |
|---|
| OK |
| NG |
OK
NG