Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › from 2019.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B2799  Engine Immobiliser System Malfunction  B279986  Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid  


DESCRIPTION

The ECM stores this DTC when the communication line between the ECM and transponder key ECU assembly is malfunctioning or the communication ID of the ECM and transponder key ECU assembly do not match.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2799 Engine Immobiliser System Malfunction Either condition is met (1 trip detection logic*2):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.


B279986 Engine Immobiliser System Signal (Some Circuit Quantity, Reported via Serial Data) Invalid Either condition is met (1 trip detection logic*2):
·

A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly.

·

A communication code cannot be verified during communication between the ECM and transponder key ECU assembly.


·

Wire harness or connector

·

Transponder key ECU assembly

·

ECM


DTC Output Confirmation Operation:
·

Start the engine and wait 10 seconds.*1

·

After disconnecting and reconnecting the cable to the negative (-) battery terminal, turn the ignition switch to ON and wait 10 seconds.*2

*1: Communication starts within 3 seconds of starting the engine. If verification fails, this DTC is stored 6 seconds after communication has completed.

*2: Communication starts within 3 seconds of turning the ignition switch to ON. If verification fails, this DTC is stored 6 seconds after communication has completed.



DTC Detection Conditions
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition Engine start operation. ○ ○
Malfunction Status A malfunction occurs in the communication or communication lines between the ECM and transponder key ECU assembly. ○ -
A communication code cannot be verified during communication between the ECM and transponder key ECU assembly. - ○
Detection Time - -
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started -

Related Data List and Active Test
DTC No. Data List and Active Test
·

B2799*1

·

B279986*2


-

*1: for 3ZR-FAE

*2: for 8NR-FTS

WIRING DIAGRAM

E329286E34
0.417,2.938 0.875,3.135 0.458,0.198 10 false F137 0.417,3.104 1.844,3.521 1.427,0.417 10 false Transponder Key ECU Assembly 5.875,2.938 6.333,3.135 0.458,0.198 10 false A38 5.875,3.094 6.333,3.292 0.458,0.198 10 false ECM 5.323,1.906 5.781,2.104 0.458,0.198 10 false IMI 5.323,1 5.781,1.198 0.458,0.198 10 false IMO 5.49,1.563 5.885,1.813 0.396,0.25 10 false 12 V 1.188,0.354 1.583,0.604 0.396,0.25 10 false 12 V 1.573,0.99 2.188,1.188 0.615,0.198 10 false EFII 1.531,1.906 2.146,2.104 0.615,0.198 10 false EFIO 1.979,0.99 2.313,1.219 0.333,0.229 10 false 10 1.979,1.906 2.427,2.177 0.448,0.271 10 false 11 5.031,1.01 5.344,1.208 0.313,0.198 10 false 45 5.021,1.906 5.333,2.104 0.313,0.198 10 false 28

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



HINT:

If transponder key ECU assembly DTCs are output simultaneously, troubleshoot the transponder key ECU assembly DTCs first.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Clear DTCs
50002 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Start the engine.


b.

Check for DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

B2799*1 or B279986*2 is not output.


Result:
Result Proceed to
OK A
NG (DTC B2799*1 or B279986*2 is output) B
NG (Other DTCs are output) C


*1: for 3ZR-FAE

*2: for 8NR-FTS


A

B

3.INSPECT ECM (TERMINAL IMO)

C

GO TO DIAGNOSTIC TROUBLE CODE CHART

3.INSPECT ECM (TERMINAL IMO)
a.

Using an oscilloscope, check the waveform

B319577C59
5.417,0.385 5.833,0.667 0.417,0.281 5.188,2.01 4.906,1.302 true 0.292,0.385 0.604,0.583 0.313,0.198 10 false *a 1.01,4.042 1.396,4.292 0.385,0.25 10 false GND 2.938,4.094 3.323,4.344 0.385,0.25 10 false *b 5.521,0.448 5.906,0.698 0.385,0.25 10 false A38 5.115,2.073 5.5,2.323 0.385,0.25 10 false IMO
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection A38-45 (IMO) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


Result:
Result Proceed to
OK A
NG (Terminal IMO stuck low (2.4 V or less)) B
NG (Terminal IMO stuck high (12 V) or abnormal waveform) C



A

4.INSPECT ECM (TERMINAL IMI)

B

10.INSPECT ECM (IMO TERMINAL VOLTAGE)

C

7.REPLACE ECM
4.INSPECT ECM (TERMINAL IMI)
a.

Using an oscilloscope, check the waveform

B319576C32
5.396,0.396 5.76,0.656 0.365,0.26 5.125,1.958 5.125,1.208 true 0.313,0.406 0.625,0.604 0.313,0.198 10 false *a 1.01,4.042 1.427,4.302 0.417,0.26 10 false GND 3.333,4.125 3.75,4.385 0.417,0.26 10 false *b 5.052,2.031 5.469,2.292 0.417,0.26 10 false IMI 5.479,0.448 5.896,0.708 0.417,0.26 10 false A38
*a Component with harness connected
(ECM)
*b Waveform


Measurement Condition
Item Content
Tester Connection A38-28 (IMI) - Body ground
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Ignition switch ON


OK:

Waveform is similar to that shown in the illustration.


Result:
Result Proceed to
OK A
NG B



A

5.REGISTER ECU COMMUNICATION ID

B

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
5.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

6.CHECK WHETHER ENGINE STARTS
6.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (COMMUNICATION ID REGISTRATION WAS DEFECTIVE)

NG

7.REPLACE ECM
7.REPLACE ECM
a.

Temporarily replace the ECM with a new one.

for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>ECM>REMOVAL

for 8NR-FTS: Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>ECM>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.REGISTER ECU COMMUNICATION ID
8.REGISTER ECU COMMUNICATION ID
a.

Reregister the ECU communication ID.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

9.CHECK WHETHER ENGINE STARTS
9.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY

10.INSPECT ECM (IMO TERMINAL VOLTAGE)
a.

Disconnect the ECM connector


b.

Turn the ignition switch to ON


c.
B410154C12
0.333,1 0.74,1.26 0.406,0.26 2.76,1.948 2.594,1.365 true 0.198,0.198 0.51,0.396 0.313,0.198 10 false *a 0.385,1.052 0.74,1.25 0.354,0.198 10 false A38 2.708,1.958 3.104,2.156 0.396,0.198 10 false IMO
*a Front view of wire harness connector
(to ECM)


Measure the voltage according to the value(s) in the table below

Standard Voltage:
Tester Connection Condition Result
A38-45 (IMO) - Body ground Ignition switch turned to ON using registered key Terminal IMO stuck low (2.4 V or less)
Terminal IMO stuck high (12 V) or Abnormal waveform



Result:
Result Proceed to
Terminal IMO stuck low (2.4 V or less) A
Terminal IMO stuck high (12 V) or Abnormal waveform B



A

11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)

B

7.REPLACE ECM
11.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM AND BODY GROUND)
a.

Disconnect the F137 transponder key ECU assembly connector


b.

Disconnect the A38 ECM connector


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
F137-10 (EFII) - A38-45 (IMO) Always Below 1 Ω
A38-45 (IMO) - Body ground Always 10 kΩ or higher
F137-10 (EFII) - Body ground Always 10 kΩ or higher
F137-11 (EFIO) - A38-28 (IMI) Always Below 1 Ω
A38-28 (IMI) - Body ground Always 10 kΩ or higher
F137-11 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.


NOTICE:

Key ID code registration is necessary when replacing the transponder key ECU assembly.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.CHECK WHETHER ENGINE STARTS
13.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally.



Result:
Result Proceed to
OK A
NG (for 3ZR-FAE) B
NG (for 8NR-FTS) C



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C