Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › ECM › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0293872 ECM A

3ZR-FAE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link

*1: When performing learning using the GTS.

Click here(Click here)

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Simple intelligent parking assist system*1 (Click here)
Toyota parking assist-sensor system*1
Initialize back door lock Power door lock control system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) registration MIL comes on (Click here)
ECU Communication ID Registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Entry and start system

·

Engine start function

·

Steering lock system


See Service Bulletin for the registration method. (w/ Entry and Start System)
Engine starting See Service Bulletin for the registration method. (w/o Entry and Start System)
Perform the following procedures in the order shown:
1.

Reset memory

2.

Deceleration sensor zero point calibration

3.

CVT oil pressure calibration


Deterioration of fuel efficiency (Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Perform the Vehicle Identification Number (VIN) registration when replacing the ECM.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click hereGeneral>MAINTENANCE>3ZR-FAE BATTERY>REMOVAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 53141F 5.REMOVE RADIATOR COVER

Hide 17751 6.REMOVE NO. 1 AIR CLEANER INLET

Hide 17701 7.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A393405

Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.


b.
A393406

Remove the 2 bolts and air cleaner case sub-assembly from the vehicle.


Hide 89661 8.REMOVE ECM

a.
A393527

Raise the 2 levers while pushing the locks on the levers, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A393407

Remove the No. 1 relay block cover from the No. 1 engine room relay block.


c.
A393537

Disconnect the 3 connectors from the engine room relay block assembly.


d.

Disengage the 2 claws to separate the engine wire from the No. 1 engine room relay block.


e.
A393528

Remove the bolt, nut and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 9.REMOVE NO. 1 ECM BRACKET

a.
A393529

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 10.REMOVE NO. 2 ECM BRACKET

a.
A393530

Remove the 2 screws and No. 2 ECM bracket from the ECM.