Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM (w/o Entry and Start System) › from 2019.09
RM32H0E _58 Vehicle Interior _060784 THEFT DETERRENT / KEYLESS ENTRY _0299017 IMMOBILISER SYSTEM(w/o Entry and Start System) C

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Entry and Start System)  B279A  Theft Deterrent System Communication Line High Fixation  B279A12  Engine Immobiliser System Circuit Short to Battery  


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck high (e.g. shorted to +B), the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
B279A Theft Deterrent System Communication Line High Fixation Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.


B279A12 Engine Immobiliser System Circuit Short to Battery Communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck high.
·

Wire harness or connector

·

ECM

·

Transponder key ECU assembly


DTC Output Confirmation Operation:

Turn the ignition switch to ON and wait 6 seconds.



Vehicle Condition and Fail-safe Operation when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Operation when Malfunction Detected
Engine cannot be started (initial ignition occurs and engine cranks, then ignition stops) Engine cannot be started

Related Data List and Active Test
DTC No. Data List and Active Test
·

B279A*1

·

B279A12*2


-

*1: for 3ZR-FAE

*2: for 8NR-FTS


WIRING DIAGRAM

E323111E17
0.573,2.104 2,2.552 1.427,0.448 10 false Transponder Key ECU Assembly 5.698,2.083 6.104,2.406 0.406,0.323 10 false ECM 5.698,1.927 6.052,2.073 0.354,0.146 10 false A38 0.583,1.917 0.938,2.063 0.354,0.146 10 false F137 1.708,0.917 2.063,1.063 0.354,0.146 10 false EFIO 2.167,0.917 2.479,1.125 0.313,0.208 10 false 11 4.875,0.927 5.073,1.094 0.198,0.167 10 false 28 5.146,0.927 5.5,1.073 0.354,0.146 10 false IMI 6.104,0.427 6.458,0.573 0.354,0.146 10 false 12 V

CAUTION / NOTICE / HINT

NOTICE:
·

If the transponder key ECU assembly or ECM is replaced, refer to Service Bulletin.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".



PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Clear DTCs
50002 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A*1 or B279A12*2 is not output.


Result:
Result Proceed to
B279A*1 or B279A12*2 is not output A
B279A*1 or B279A12*2 is output B


*1: for 3ZR-FAE

*2: for 8NR-FTS



A

B

3.CHECK CONNECTION OF CONNECTOR
3.CHECK CONNECTION OF CONNECTOR
a.

Check that the connectors are properly connected to the ECM and transponder key ECU assembly.

OK:

Connectors are properly connected.



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

4.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the F137 transponder key ECU assembly connector


b.

Disconnect the A38 ECM connector


c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
F137-11 (EFIO) - A38-28 (IMI) Always Below 1 Ω
F137-11 (EFIO) - Body ground Always 10 kΩ or higher
A38-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.


Result:
Proceed to
NEXT



NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Clear the DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Clear DTCs
50002 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Clear DTCs
50002 234


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTC
7.CHECK FOR DTC
a.

Check for DTCs.

i.

for 8NR-FTS:

Powertrain > Engine > Trouble Codes
50001 372

ii.

for 3ZR-FAE:

Powertrain > Engine and ECT > Trouble Codes
50001 234


HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.


OK:

DTC B279A*1 or B279A12*2 is not output.


Result:
Result Proceed to
B279A*1 or B279A12*2 is not output A
B279A is output (for 3ZR-FAE) B
B279A12 is output (for 8NR-FTS) C


*1: for 3ZR-FAE

*2: for 8NR-FTS



A

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

B

C