Home › Engine / Hybrid System › 3ZR-FAE (ENGINE CONTROL) › SFI SYSTEM › from 2019.09
RM32H0E _51 Engine / Hybrid System _059607 3ZR-FAE ENGINE CONTROL _0292315 SFI SYSTEM C

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  P0351  Ignition Coil "A" Primary / Secondary Circuit  P0352  Ignition Coil "B" Primary / Secondary Circuit  P0353  Ignition Coil "C" Primary / Secondary Circuit  P0354  Ignition Coil "D" Primary / Secondary Circuit  


DESCRIPTION

HINT:
·

These DTCs indicate malfunctions relating to the primary circuit.

·

If DTC P0351 is output, check the ignition coil assembly (No. 1 cylinder) circuit.

·

If DTC P0352 is output, check the ignition coil assembly (No. 2 cylinder) circuit.

·

If DTC P0353 is output, check the ignition coil assembly (No. 3 cylinder) circuit.

·

If DTC P0354 is output, check the ignition coil assembly (No. 4 cylinder) circuit.



A Direct Ignition System (DIS) is used on this vehicle.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

A288665E14
4.5,0.781 4.417,0.365 4.417,0.365 4.333,0.365 true 5.365,0.531 5.583,0.406 5.583,0.406 5.719,0.406 true 0.469,0.875 2.26,1.073 1.792,0.198 10 false Crankshaft Position Sensor 0.448,2.677 2.24,2.875 1.792,0.198 10 false Camshaft Position Sensor 0.323,3.708 2.25,4.406 1.927,0.698 10 false Other Sensors (Engine Coolant Temperature Sensor, Mass Air Flow Meter, Throttle Position Sensor, etc.) 3.031,0.823 3.385,1 0.354,0.177 10 false IGT1 3.031,1.135 3.385,1.313 0.354,0.177 10 false IGF1 5.115,0.073 6.438,0.26 1.323,0.188 10 false from Battery 3.927,0.271 4.417,0.5 0.49,0.229 10 false Igniter 5.76,0.333 7.146,0.896 1.385,0.563 10 false Ignition Coil Assembly (No. 1 Cylinder) 5.927,1.25 7.063,1.469 1.135,0.219 10 false Spark Plug 5.927,2.469 7.063,2.688 1.135,0.219 10 false Spark Plug 5.917,3.781 7.052,4 1.135,0.219 10 false Spark Plug 5.958,5.104 7.094,5.323 1.135,0.219 10 false Spark Plug 3,2.156 3.354,2.333 0.354,0.177 10 false IGT2 3,3.479 3.354,3.656 0.354,0.177 10 false IGT3 3.031,4.792 3.385,4.969 0.354,0.177 10 false IGT4 3.813,2.771 6.271,2.958 2.458,0.188 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.823,4.094 6.281,4.281 2.458,0.188 10 false Ignition Coil Assembly (No. 3 Cylinder) 3.781,5.375 6.24,5.563 2.458,0.188 10 false Ignition Coil Assembly (No. 4 Cylinder) 2.854,5.323 3.208,5.5 0.354,0.177 10 false ECM

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0351 Ignition Coil "A" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT1 circuit between ignition coil assembly and ECM

·

Ignition coil assembly (No. 1 cylinder)

·

ECM


Comes on DTC stored
P0352 Ignition Coil "B" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT2 circuit between ignition coil assembly and ECM

·

Ignition coil assembly (No. 2 cylinder)

·

ECM


Comes on DTC stored
P0353 Ignition Coil "C" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT3 circuit between ignition coil assembly and ECM

·

Ignition coil assembly (No. 3 cylinder)

·

ECM


Comes on DTC stored
P0354 Ignition Coil "D" Primary / Secondary Circuit No IGF signal to the ECM while the engine is running (1 trip detection logic).
·

Ignition system

·

Open or short in IGF1 or IGT4 circuit between ignition coil assembly and ECM

·

Ignition coil assembly (No. 4 cylinder)

·

ECM


Comes on DTC stored

Reference: Inspection using an oscilloscope.

A285441E06
2.906,1 3.333,1.25 0.427,0.25 10 GND 2.896,1.615 3.292,1.833 0.396,0.219 10 GND 0.104,0.688 0.448,1.073 0.344,0.385 10 CH1 (IGT) 0.104,1.198 0.448,1.594 0.344,0.396 10 CH2 (IGF) 1.281,1.896 2.052,2.073 0.771,0.177 10 20 ms./DIV. 0.042,0.115 0.708,0.281 0.667,0.167 10 2 V/DIV.


While idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connector.

ECM Terminal Name CH1: Between IGT (1 to 4) and E1
CH2: Between IGF1 and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

A212405E25
1.781,1.646 2.177,1.823 0.396,0.177 10 ECM 2.958,1.302 3.229,1.49 0.271,0.188 10 IGT 2.948,1.729 3.229,1.885 0.281,0.156 10 IGF 4.156,1.51 4.594,1.656 0.438,0.146 10 Igniter 5.396,1.344 6.167,1.521 0.771,0.177 10 Ignition Coil 4.396,2.354 6.073,2.542 1.677,0.188 10 Ignition Coil Assembly 0.208,3.115 1.125,3.448 0.917,0.333 10 Ignition Signal (IGT) 1.646,3.542 2.135,3.729 0.49,0.188 10 Normal 1.385,3.948 2.156,4.135 0.771,0.188 10 Malfunction 0.188,3.896 1.042,4.469 0.854,0.573 10 Ignition Confirmation Signal (IGF) 3.635,4.51 4.875,4.719 1.24,0.208 10 Circuit Malfunction 5.948,4.969 6.313,5.167 0.365,0.198 10 Time

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Igniter
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 seconds or more.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P0351, P0352, P0353 or P0354.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A384872E04
0.542,7.802 1.615,8 1.073,0.198 10 false Battery 0.354,6.75 1.729,6.948 1.375,0.198 10 false BATT MAIN 0.344,2.979 1.417,3.177 1.073,0.198 10 false IGN/INJ 3.208,1.458 3.667,1.656 0.458,0.198 10 false C21 3.219,3.125 3.677,3.323 0.458,0.198 10 false C22 3.219,4.792 3.677,4.99 0.458,0.198 10 false C23 3.219,6.448 3.677,6.646 0.458,0.198 10 false C24 5.448,7.813 5.906,8.01 0.458,0.198 10 false A38 5.458,2.469 5.917,2.667 0.458,0.198 10 false C63 5.49,5.719 5.948,5.917 0.458,0.198 10 false C63 5.448,4.125 5.906,4.323 0.458,0.198 10 false C63 5.448,6.146 5.906,6.344 0.458,0.198 10 false C63 5.458,0.75 5.917,0.948 0.458,0.198 10 false C63 5.813,0.615 6.427,0.813 0.615,0.198 10 false IGT1 5.813,2.323 6.427,2.521 0.615,0.198 10 false IGT2 5.823,3.979 6.438,4.177 0.615,0.198 10 false IGT3 5.823,5.583 6.438,5.781 0.615,0.198 10 false IGT4 5.823,6.01 6.438,6.208 0.615,0.198 10 false IGF1 5.51,5.917 5.823,6.115 0.313,0.198 10 false 71 5.521,5.5 5.833,5.698 0.313,0.198 10 false 72 5.5,3.906 5.813,4.104 0.313,0.198 10 false 73 5.51,2.25 5.823,2.448 0.313,0.198 10 false 74 5.51,0.542 5.823,0.74 0.313,0.198 10 false 75 3.271,4.125 3.583,4.323 0.313,0.198 10 false +B 3.271,5.708 3.583,5.906 0.313,0.198 10 false +B 3.271,2.448 3.583,2.646 0.313,0.198 10 false +B 3.271,0.74 3.583,0.938 0.313,0.198 10 false +B 5.5,7.594 5.74,7.781 0.24,0.188 10 false 46 3.115,0.635 3.271,0.833 0.156,0.198 10 false 1 3.094,5.615 3.25,5.813 0.156,0.198 10 false 1 3.104,4.01 3.26,4.208 0.156,0.198 10 false 1 3.104,2.354 3.26,2.552 0.156,0.198 10 false 1 4.729,0.979 4.885,1.177 0.156,0.198 10 false 2 4.729,6.01 4.885,6.208 0.156,0.198 10 false 2 4.729,2.667 4.885,2.865 0.156,0.198 10 false 2 4.729,4.323 4.885,4.521 0.156,0.198 10 false 2 4.417,2.781 4.875,2.979 0.458,0.198 10 false IGF 4.417,6.125 4.875,6.323 0.458,0.198 10 false IGF 4.406,4.458 4.865,4.656 0.458,0.198 10 false IGF 4.406,1.094 4.865,1.292 0.458,0.198 10 false IGF 3.271,6.125 3.729,6.323 0.458,0.198 10 false GND 3.271,4.448 3.729,4.646 0.458,0.198 10 false GND 3.271,1.094 3.729,1.292 0.458,0.198 10 false GND 3.271,2.781 3.729,2.979 0.458,0.198 10 false GND 3.208,1.583 4.594,2.344 1.385,0.76 10 false Ignition Coil Assembly (No. 1 Cylinder) 3.24,3.25 4.615,3.979 1.375,0.729 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.219,4.917 4.594,5.531 1.375,0.615 10 false Ignition Coil Assembly (No. 3 Cylinder) 3.219,6.604 4.583,7.542 1.365,0.938 10 false Ignition Coil Assembly (No. 4 Cylinder) 3.104,6.021 3.26,6.219 0.156,0.198 10 false 4 3.104,4.333 3.26,4.531 0.156,0.198 10 false 4 6.208,8.531 6.667,8.729 0.458,0.198 10 false ECM 3.104,2.688 3.365,2.917 0.26,0.229 10 false 4 3.125,0.979 3.281,1.177 0.156,0.198 10 false 4 4.729,5.615 4.885,5.813 0.156,0.198 10 false 3 4.729,4.01 4.885,4.208 0.156,0.198 10 false 3 4.729,2.354 4.885,2.552 0.156,0.198 10 false 3 4.729,0.635 4.885,0.833 0.156,0.198 10 false 3 4.354,0.75 4.969,0.948 0.615,0.198 10 false IGT1 4.333,2.458 4.948,2.656 0.615,0.198 10 false IGT2 4.344,4.135 4.958,4.333 0.615,0.198 10 false IGT3 4.344,5.729 4.958,5.927 0.615,0.198 10 false IGT4 1.031,1.604 2.26,1.802 1.229,0.198 10 false EFI-MAIN 0.906,2.042 1.219,2.24 0.313,0.198 10 false 1B 0.896,2.198 2.052,2.646 1.156,0.448 10 false No. 1 Integration Relay 0.75,1.146 0.906,1.344 0.156,0.198 10 false 5 1.833,1.146 1.99,1.344 0.156,0.198 10 false 6 1.833,0.635 1.99,0.833 0.156,0.198 10 false 4 0.76,0.646 0.917,0.844 0.156,0.198 10 false 3 5.823,7.688 6.438,7.885 0.615,0.198 10 false MREL 1.125,5.604 2.167,5.99 1.042,0.385 10 false EFI-MAIN NO. 1 0.458,4.958 1.094,5.354 0.635,0.396 10 false EFI-MAIN NO. 1 1.115,5.156 1.333,5.417 0.219,0.26 10 false 2 2,5.167 2.156,5.365 0.156,0.198 10 false 1 1.115,4.688 1.271,4.885 0.156,0.198 10 false 5 1.99,4.688 2.146,4.885 0.156,0.198 10 false 3 2.24,2.875 2.698,3.26 0.458,0.385 10 false EFI NO. 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the C21, C22, C23 and C24 ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-4 (GND) - Body ground Always Below 1 Ω
C22-4 (GND) - Body ground Always Below 1 Ω
C23-4 (GND) - Body ground Always Below 1 Ω
C24-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
a.
A347474C37
0.188,1.073 0.573,1.313 0.385,0.24 0.188,1.479 0.573,1.719 0.385,0.24 0.188,1.875 0.573,2.115 0.385,0.24 0.188,2.271 0.573,2.51 0.385,0.24 1.083,2.792 1.271,2.281 true 2.677,2.99 2.135,2.281 true 0.188,0.177 0.646,0.375 0.458,0.198 10 false *a 0.25,1.115 0.708,1.313 0.458,0.198 10 false C21 0.25,1.521 0.708,1.719 0.458,0.198 10 false C22 0.25,1.917 0.708,2.115 0.458,0.198 10 false C23 0.26,2.313 0.719,2.51 0.458,0.198 10 false C24 0.99,2.813 1.448,3.01 0.458,0.198 10 false +B 2.625,3.063 3.083,3.26 0.458,0.198 10 false GND
*a Front view of wire harness connector
(to Ignition Coil Assembly)


Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C21-1 (+B) - C21-4 (GND) Ignition switch ON 11 to 14 V
C22-1 (+B) - C22-4 (GND) Ignition switch ON 11 to 14 V
C23-1 (+B) - C23-4 (GND) Ignition switch ON 11 to 14 V
C24-1 (+B) - C24-4 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the C21, C22, C23 and C24 ignition coil assembly connectors.


b.

Disconnect the C63 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C21-2 (IGF) - C63-71 (IGF1) Always Below 1 Ω
C22-2 (IGF) - C63-71 (IGF1) Always Below 1 Ω
C23-2 (IGF) - C63-71 (IGF1) Always Below 1 Ω
C24-2 (IGF) - C63-71 (IGF1) Always Below 1 Ω
C21-3 (IGT1) - C63-75 (IGT1) Always Below 1 Ω
C22-3 (IGT2) - C63-74 (IGT2) Always Below 1 Ω
C23-3 (IGT3) - C63-73 (IGT3) Always Below 1 Ω
C24-3 (IGT4) - C63-72 (IGT4) Always Below 1 Ω
C21-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C22-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C23-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C24-2 (IGF) or C63-71 (IGF1) - Body ground and other terminals Always 10 kΩ or higher
C21-3 (IGT1) or C63-75 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C22-3 (IGT2) or C63-74 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C23-3 (IGT3) or C63-73 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C24-3 (IGT4) or C63-72 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 4 cylinders).

NOTICE:

Do not change the location of the connectors.



f.

Perform a simulation test.


g.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

h.

Read the DTCs.

Result:
Result Proceed to
Same DTC output A
Different ignition coil DTC output B


HINT:

Perform "Inspection After Repair" after replacing the ignition coil assembly.

Click hereEngine / Hybrid System>3ZR-FAE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION




A

B