Home › Engine / Hybrid System › 8NR-FTS (ENGINE CONTROL) › SFI SYSTEM › from 2020.08
RM32H0E _51 Engine / Hybrid System _059353 8NR-FTS ENGINE CONTROL _0290422 SFI SYSTEM C

8NR-FTS ENGINE CONTROL  SFI SYSTEM  P246300  Particulate Filter Restriction - Soot Accumulation Bank 1  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P246300 Particulate Filter Restriction - Soot Accumulation Bank 1 During high load operation, the PM (Particulate Matter) accumulation ratio is 100% or higher for 1 second or more (1 trip detection logic). Front exhaust pipe assembly (GPF) Comes on*/-
*: The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.
DTC stored SAE Code:
P2463

MONITOR DESCRIPTION

When the accumulation ratio of the PM in the GPF (Gasoline Particulate Filter) is at the specified value or higher, output is limited during high load operation to prevent the GPF from rising to a high temperature. A DTC is stored at this time.

The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and wait 10 seconds or more.

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P246300.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.



13.

Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.

14.

Read the value displayed on the GTS.

HINT:
·

If the PM Depensition Ratio value is less than 100%, the system is normal.

·

If the PM Depensition Ratio value is 100% or higher, perform forced particulate filter rejuvenation.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Clear the Vehicle Control History after completing repairs.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY



PROCEDURE

1.READ VALUE USING GTS (ASH DEPOSITION RATIO BANK1)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Ash Deposition Ratio Bank1.

Powertrain > Engine > Data List
Tester Display
Ash Deposition Ratio Bank1
50003 372 822

e.

Read the value displayed on the GTS.

Standard:
GTS Display Specified Condition
Ash Deposition Ratio Bank1 Less than 100%



Result:
Proceed to
OK
NG



OK

2.CLEAR DTC

NG

5.REPLACE FRONT EXHAUST PIPE ASSEMBLY (GPF)
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CLEAR VEHICLE CONTROL HISTORY
3.CLEAR VEHICLE CONTROL HISTORY
a.

Turn the ignition switch to ON.


b.

Turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) / Clear.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.


Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

d.

Clear the Vehicle Control History.


Result:
Proceed to
NEXT



NEXT

4.PERFORM PM REJUVENATE MODE
4.PERFORM PM REJUVENATE MODE

Result:
Proceed to
NEXT



NEXT

END

5.REPLACE FRONT EXHAUST PIPE ASSEMBLY (GPF)
a.

Replace the front exhaust pipe assembly (GPF).

Click hereEngine / Hybrid System>8NR-FTS (INTAKE / EXHAUST)>EXHAUST PIPE (for 2WD)>REMOVAL


Result:
Proceed to
NEXT


HINT:

Clear the GPF deterioration record using the GTS after replacing the front exhaust pipe assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



NEXT

6.CLEAR VEHICLE CONTROL HISTORY
6.CLEAR VEHICLE CONTROL HISTORY
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) / Clear.

NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.


Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55

e.

Clear the Vehicle Control History.


Result:
Proceed to
NEXT



NEXT

END