Home › Engine / Hybrid System › 8NR-FTS (FUEL) › FUEL INJECTOR › from 2020.08
RM32H0E _51 Engine / Hybrid System _059909 8NR-FTS FUEL _0293895 FUEL INJECTOR A

8NR-FTS FUEL  FUEL INJECTOR  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of fuel injector assembly Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 82124 6.DISCONNECT NO. 4 ENGINE WIRE

a.
A350910

Disconnect the 4 fuel injector assembly connectors.


b.

Disconnect the fuel pressure sensor connector.


Hide 23814B 7.REMOVE FUEL DELIVERY PIPE

a.
A417839

Remove the 5 bolts and fuel delivery pipe with the fuel injector assemblies.

NOTICE:
·

Make sure not to touch or strike the tips of the fuel injector assemblies.

·

Pull and remove the fuel delivery pipe in a straight line without tilting it.




Hide 23250 8.REMOVE FUEL INJECTOR ASSEMBLY

a.
A350912N02
2.115,2.104 2.729,2.302 0.615,0.198 10 false NO. 3

Secure the fuel delivery pipe in a vise between aluminum plates and pull out the 4 fuel injector assemblies.

NOTICE:
·

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe O-ring.

·

After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe side.

·

Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.




b.

Remove the nozzle holder clamp from each fuel injector assembly.


c.

Using needle nose pliers, remove the No. 3 fuel injector back-up ring from each fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.



d.

Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.


e.

Remove the C-ring and injector vibration insulator from each fuel injector assembly.


Hide 23255A 9.REMOVE FUEL INJECTOR SEAL

a.
A273082

Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:
·

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.

·

If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.




b.

Remove the fuel injector seal from each fuel injector assembly.