Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › from 2020.08
RM32H0E _59 Vehicle Exterior _060314 WINDOW / GLASS _0298548 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When replacing the windshield glass of a vehicle equipped with a forward recognition camera, make sure to use a Toyota genuine part. If a non-Toyota genuine part is used, the forward recognition camera may not be able to be installed due to a missing bracket. Also, the dynamic radar cruise control system, lane tracing assist system, pre-collision system, front camera system, road sign assist system or automatic high beam system may not operate properly due to a difference in the transmissivity or black ceramic border.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 56111 1.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any remaining adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean it with a non-residue solvent.





Hide 56115A 2.INSTALL NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B454711

Install 2 new No. 1 windshield glass stoppers to the vehicle body as shown in the illustration.

HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 56116C 3.INSTALL NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

Using a brush or sponge, coat the installation area of the 2 No. 2 windshield glass stoppers with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454713C01
1.083,0.75 1.302,0.99 false 1.615,1.208 1.5,1.667 true 1.333,1.25 1.5,1.667 1.5,1.667 1.906,1.135 true 0.167,0.094 0.542,0.333 0.375,0.24 10 false *a 0.896,0.625 1.271,0.865 0.375,0.24 10 false *c 1.417,1.677 1.792,1.917 0.375,0.24 10 false *b 2.677,0.854 2.844,1.104 0.167,0.25 10 false a
*a Back Side of Windshield Glass
*b Ceramic Notch
*c Windshield Glass Edge Side


Install 2 new No. 2 windshield glass stoppers to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 13.7 to 14.7 mm (0.539 to 0.579 in.)


HINT:

Only 2-piece type windshield glass stoppers are provided as supply parts. Use 2-piece type stoppers as replacements even if 1-piece type stoppers were originally installed.



Hide 75533G 4.INSTALL WINDSHIELD OUTSIDE MOULDING

a.

Using a brush or sponge, coat the installation area of the windshield outside moulding with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454714C01
0.792,2.042 1,2.417 true 2.417,2.417 2.635,2.042 true 0.167,0.135 0.5,0.458 0.333,0.323 10 false *a 1.01,2.469 1.323,2.625 0.313,0.156 10 false *b 0.781,1.573 1.031,1.74 0.25,0.167 10 false b 2.604,1.573 2.854,1.74 0.25,0.167 10 false b 2.313,2.469 2.625,2.625 0.313,0.156 10 false *b 1.99,3.063 2.302,3.219 0.313,0.156 10 false a 1.052,3.167 1.448,3.333 0.396,0.167 10 false A-A 1.229,0.552 1.479,0.719 0.25,0.167 10 false A 1.24,1.167 1.49,1.333 0.25,0.167 10 false A
*a Back Side of Windshield Glass
*b Edge of Curved Surface


Install a new windshield outside moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 6.5 mm (0.256 in.)
b 2.5 to 7.5 mm (0.098 to 0.295 in.)



Hide 56117A 5.INSTALL WINDOW GLASS ADHESIVE DAM

a.
B274197C02
3.094,0.802 2.427,0.427 false 1.531,1.729 1.688,1.927 0.156,0.198 10 false a 2.26,0.344 2.573,0.542 0.313,0.198 10 false *a
*a Cut


Cut a new window glass adhesive dam so that it is the appropriate size as shown in the illustration.

Standard Dimension:
Area Dimension
a 297.9 cm (9.77 ft.)



b.

Using a brush or sponge, coat the installation area of the window glass adhesive dam with primer G.

NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



c.

Install a new window glass adhesive dam to the windshield glass as shown in the illustration.

B454715C01
5,1.583 5.333,1.115 true 5.083,3 5.344,2.594 true 3.375,3.396 3.906,3.51 3.906,3.51 3.573,3.26 false 2.25,1 1.938,1.073 true 0.177,0.104 0.51,0.438 0.333,0.333 10 false *a 3.51,2.156 3.76,2.323 0.25,0.167 10 false A 2.354,0.885 2.667,1.042 0.313,0.156 10 false *b 4.948,3.042 5.26,3.198 0.313,0.156 10 false *c 4.813,0.573 5.313,0.729 0.5,0.156 10 false A-A 4.76,2.156 5.26,2.313 0.5,0.156 10 false B-B 3.99,3.479 4.302,3.635 0.313,0.156 10 false *b 4.833,1.604 5.146,1.76 0.313,0.156 10 false *c 3.177,2.219 3.427,2.385 0.25,0.167 10 false A 2.667,3.188 2.917,3.354 0.25,0.167 10 false B 2.667,3.573 2.917,3.74 0.25,0.167 10 false B
*a Back Side of Windshield Glass *b Ceramic Notch
*c Window Glass Adhesive Dam Positioning Center - -
V100155

Primer G - -



Hide 56153C 6.INSTALL FRONT WINDOW INNER CENTER MOULDING

HINT:

Perform the following procedure only when replacement of a front window inner center moulding is necessary.


a.
B454716C01
0.188,0.177 0.5,0.5 0.313,0.323 10 false *a 0.635,1.865 0.948,2.021 0.313,0.156 10 false A 0.698,3 1.115,3.167 0.417,0.167 10 false A-A 0.563,2.365 0.875,2.521 0.313,0.156 10 false A 1.469,3.073 1.885,3.24 0.417,0.167 10 false a
*a Back Side of Windshield Glass
V100155

Primer G


Using a brush or sponge, coat the installation area of the front window inner center moulding with primer G.

Standard Dimension:
Area Dimension
a 14.5 mm (0.571 in.)


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



b.
B454717C01
1.583,2.5 1.583,2.417 1.583,2.417 2.083,2.417 false 1.833,2.417 1.833,2.5 false 0.167,0.083 0.5,0.333 0.333,0.25 10 false *a 2.125,2.333 2.438,2.49 0.313,0.156 10 false *b 1.031,4.188 1.344,4.344 0.313,0.156 10 false a 0.646,1.406 0.958,1.563 0.313,0.156 10 false A 0.552,1.906 0.865,2.063 0.313,0.156 10 false A 0.354,3.406 0.833,3.563 0.479,0.156 10 false A-A
*a Back Side of Windshield Glass
*b Matchmark


Install a new front window inner center moulding to the windshield glass as shown in the illustration.

Standard Dimension:
Area Dimension
a 0.5 mm (0.020 in.) or less


NOTICE:

Do not damage the front window inner center moulding.



c.

Remove the matchmarks.


Hide 56111 7.INSTALL WINDSHIELD GLASS

a.
B388038

Clean and shape the contact surface of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.
B454704C02
1.479,1.24 1.656,1.24 true 1.479,1.927 1.479,1.01 1.479,1.01 1.646,1.01 true 1.406,1.938 1.625,2.135 0.219,0.198 10 true *a
*a Matchmark


Position the windshield glass.

i.

Using suction cups, place the windshield glass in the correct position.


ii.

Check that the whole contact surface of the windshield glass rim is perfectly even.


iii.

Align the matchmarks on the windshield glass and vehicle body.

NOTICE:

Check that the windshield glass stoppers are engaged to the vehicle body correctly.



iv.

Remove the windshield glass.



c.

Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.



d.

Using a brush or sponge, coat the adhesive application area with primer G.

B454718C01
3.26,1.74 3.667,1.833 false 3.104,2.406 3.542,2.635 3.542,2.635 3.333,2.313 true 0.167,0.208 0.479,0.542 0.313,0.333 10 false *a 3.75,1.75 4.063,1.906 0.313,0.156 10 false *b 3.552,2.688 3.865,2.844 0.313,0.156 10 false *c 1.031,0.604 1.271,0.771 0.24,0.167 10 false A 1.021,0.99 1.26,1.156 0.24,0.167 10 false A 1.667,0.667 1.906,0.833 0.24,0.167 10 false B 1.667,0.938 1.906,1.104 0.24,0.167 10 false B 2.948,1.167 3.188,1.333 0.24,0.167 10 false C 3.26,1.115 3.5,1.281 0.24,0.167 10 false C 3,2.073 3.24,2.24 0.24,0.167 10 false E 3.104,2.542 3.344,2.708 0.24,0.167 10 false E 1.219,2.156 1.458,2.323 0.24,0.167 10 false D 0.979,2.594 1.219,2.76 0.24,0.167 10 false D 0.604,3.365 0.938,3.531 0.333,0.167 10 false A-A 2.885,3.365 3.219,3.531 0.333,0.167 10 false B-B 4.917,3.333 5.25,3.5 0.333,0.167 10 false E-E 5.083,1.948 5.417,2.115 0.333,0.167 10 false D-D 5.094,0.698 5.427,0.865 0.333,0.167 10 false C-C 3.396,3.292 3.729,3.458 0.333,0.167 10 false b 5.74,3.281 6.073,3.448 0.333,0.167 10 false d 5.771,1.875 6.104,2.042 0.333,0.167 10 false c 1.438,3.281 1.771,3.448 0.333,0.167 10 false a
*a Back Side of Windshield Glass *b Adhesive Application Area
*c Ceramic Notch - -
V100155

Primer G - -


Standard Dimension:
Area Dimension
a 7.0 mm (0.276 in.)
b 10.0 mm (0.394 in.) or more
c 11.0 mm (0.433 in.) or more
d 19.0 mm (0.748 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:
·

Apply primer G to the ceramic notches.

·

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.




e.

Apply adhesive to the windshield glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Cartridge Nozzle


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12.0 to 15.0 mm (0.472 to 0.591 in.)
b 8.0 to 11.0 mm (0.315 to 0.433 in.)



ii.

Load the sealer gun with the cartridge.


iii.

Apply adhesive to the windshield glass as shown in the illustration.

B454719C01
5.083,4.25 5.406,3.823 true 3.271,1.781 3.75,1.917 false 3.135,2.406 3.667,2.583 3.667,2.583 3.313,2.26 true 5.333,2.833 5.615,2.438 true 0.167,0.083 0.5,0.417 0.333,0.333 10 false *a 3.833,1.875 4.146,2.031 0.313,0.156 10 false *b 4.948,4.292 5.26,4.448 0.313,0.156 10 false *c 3.75,2.594 4.063,2.75 0.313,0.156 10 false *d 1.208,2.146 1.448,2.302 0.24,0.156 10 false D 0.51,3.333 1,3.5 0.49,0.167 10 false A-A 2.76,3.417 3.25,3.583 0.49,0.167 10 false B-B 4.771,3.188 5.26,3.354 0.49,0.167 10 false E-E 5.01,1.917 5.5,2.083 0.49,0.167 10 false D-D 5.167,0.5 5.656,0.667 0.49,0.167 10 false C-C 6.24,0.365 6.479,0.615 0.24,0.25 10 false b 5.667,1.771 5.833,2.021 0.167,0.25 10 false c 5.469,3.01 5.635,3.26 0.167,0.25 10 false c 5.677,3.417 5.844,3.667 0.167,0.25 10 false d 3.542,4.25 3.708,4.5 0.167,0.25 10 false a 1.656,4.271 1.823,4.521 0.167,0.25 10 false a 0.99,2.583 1.229,2.74 0.24,0.156 10 false D 3.094,2.563 3.333,2.719 0.24,0.156 10 false E 3.01,2.073 3.25,2.229 0.24,0.156 10 false E 2.958,1.135 3.198,1.292 0.24,0.156 10 false C 3.26,1.104 3.5,1.26 0.24,0.156 10 false C 1.656,0.688 1.896,0.844 0.24,0.156 10 false B 1.688,0.948 1.927,1.104 0.24,0.156 10 false B 1.031,1 1.271,1.156 0.24,0.156 10 false A 1.01,0.625 1.25,0.781 0.24,0.156 10 false A 5.208,2.844 5.521,3 0.313,0.156 10 false *c
*a Back Side of Windshield Glass *b Adhesive Positioning Center
*c Window Glass Adhesive Dam Positioning Center *d Ceramic Notch
V100155

Adhesive - -


Standard Dimension:
Area Dimension
a 9.5 mm (0.374 in.)
b 3.0 mm (0.118 in.)
c 6.6 mm (0.260 in.)
d 8.0 mm (0.315 in.)


HINT:

Apply adhesive to the ceramic notches.




f.
B454704C03
1.479,1.844 1.479,0.99 1.479,0.99 1.646,0.99 true 1.49,1.229 1.646,1.229 true 1.417,1.875 1.625,2.063 0.208,0.188 10 true *a
*a Matchmark


Install the windshield glass.

i.

Using suction cups, position the windshield glass so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the windshield glass stoppers are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and windshield glass.




ii.

Lightly press the outer surface of the windshield glass to ensure that the windshield glass is securely fit to the vehicle body.

HINT:

Press the glass with a force of 98 N (10 kgf, 22.0 lbf) or more.



iii.

Using a scraper, remove any excess or protruding adhesive.


iv.

Hold the windshield glass using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.




g.

When replacing the windshield glass or front window inner center moulding with a new one:

i.
B454720N01
1.896,2.01 2.052,2.208 0.156,0.198 10 false A 1.906,2.469 2.063,2.667 0.156,0.198 10 false A 0.74,3.135 1.156,3.385 0.417,0.25 10 false A-A

Remove the 2 protective retainers from the front window inner center moulding.

NOTICE:

Do not damage the front window inner center moulding.


HINT:

Make sure to remove the protective retainers.




h.

w/ Windshield Deicer System:

i.

Connect the connector of the windshield deicer.



Hide 8.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 63311C 9.INSTALL ROOF HEADLINING

a.

Return the front section of the roof headlining to its original position.


Hide 74320 11.INSTALL VISOR ASSEMBLY LH (w/ Vanity Light)

Hide 74310 12.INSTALL VISOR ASSEMBLY RH (w/ Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74320 13.INSTALL VISOR ASSEMBLY LH (w/o Vanity Light)

Hide 74310 14.INSTALL VISOR ASSEMBLY RH (w/o Vanity Light)

HINT:

Use the same procedure as for the LH side.


Hide 74325 15.INSTALL VISOR BRACKET COVER

Hide 74610A 16.INSTALL ASSIST GRIP SUB-ASSEMBLY

Hide 74612 17.INSTALL ASSIST GRIP COVER

Hide 62212 18.INSTALL FRONT PILLAR GARNISH LH

Hide 62211 19.INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62312B 20.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 21.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 81340 22.INSTALL VANITY LIGHT ASSEMBLY

Hide 81260A 23.INSTALL MAP LIGHT ASSEMBLY (for TMMT Made)

Hide 81260A 24.INSTALL MAP LIGHT ASSEMBLY (for TMC Made)

Hide 86461 25.INSTALL FORWARD RECOGNITION HOOD (w/ Pre-collision System)

Hide 8646C 26.INSTALL FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

Hide 89941 27.INSTALL RAIN SENSOR (w/ Rain Sensor)

Hide 87810 28.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 29.INSTALL INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 55708 30.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 85221B 31.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 85211B 32.INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 85292B 33.INSTALL FRONT WIPER ARM HEAD CAP

Hide 75534 34.INSTALL WINDSHIELD OUTSIDE MOULDING LH

Hide 75533 35.INSTALL WINDSHIELD OUTSIDE MOULDING RH

HINT:

Use the same procedure as for the LH side.


Hide 8646C 36.ADJUST FORWARD RECOGNITION CAMERA (w/ Pre-collision System)

a.

If the forward recognition camera has been replaced with a new one has been removed and installed, it is necessary to perform Forward Recognition Camera Learning.

HINT:

Forward Recognition Camera Learning can be performed by using either Target Adjustment (One Time Recognition) or Target Adjustment (Sequential Recognition) or Driving Adjustment.