Before performing troubleshooting for the dynamic radar cruise control system, perform troubleshooting for the pre-collision system.
Click hereVehicle Interior>PRE-COLLISION>PRE-COLLISION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
*: Use the GTS.
| Proceed to |
|---|
| NEXT |
NEXT
In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
The following 5 items are important points for problem analysis:
| What | Vehicle model, system name |
| When | Date, time, occurrence frequency |
| Where | Road conditions |
| Under what conditions? | Driving conditions, weather conditions |
| How did it happen? | Problem symptoms |
| Proceed to |
|---|
| NEXT |
NEXT
Measure the battery voltage.
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
11 to 14 V (Ignition switch off)
Check the fuses and relays.
Check the connector connections and terminals to make sure that there are no abnormalities such as loose connections, deformation, etc.
| Proceed to |
|---|
| NEXT |
NEXT
Using the GTS, perform a health check.
| Result | Proceed to |
|---|---|
| System DTCs other than DTCs related to the dynamic radar cruise control system (Cruise Control) and dynamic radar cruise control system (Radar Cruise 2) are not output. | A |
| System DTCs other than DTCs related to the dynamic radar cruise control system (Cruise Control) and dynamic radar cruise control system (Radar Cruise 2) are output. | B |
A
B
Check if a warning message is displayed on the multi-information display in the combination meter assembly.
If more than one message is displayed, perform each inspection in the order of A, B and C.
| Result | Proceed to |
|---|---|
| "Cruise Control Malfunction Visit Your Dealer" is displayed. | A |
| One of the following warning messages is displayed:
·
"Radar Cruise Control Unavailable See Owner's Manual" ·
"Radar Cruise Control Unavailable" |
B |
| No dynamic radar cruise control system warnings are displayed. | C |
A
B
C
Using the GTS, check that the CAN communication system is functioning normally.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
CAN communication system is functioning normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check for DTCs.
Make a note of any DTCs that are output.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
B
Using the GTS, check for vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Record any vehicle control history that is output.
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history X2006, X2013, X2015, X2022, X2026 or X2028 is output | B |
| Vehicle control history other than X2006, X2013, X2015, X2022, X2026 or X2028 is output | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
C
Using the GTS, clear the vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Recheck for vehicle control history.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
| Result | Proceed to |
|---|---|
| Vehicle control history is not output | A |
| Vehicle control history is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>VEHICLE CONTROL HISTORY
Clear the DTCs.
Reproduce the vehicle conditions that were present when the DTCs that were noted were stored.
Refer to each corresponding DTC for details on the detection conditions.
Recheck for DTCs.
Attempt to duplicate the malfunction and check if the DTCs are output again.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Refer to Problem Symptoms Table.
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
| Result | Proceed to |
|---|---|
| Fault is not listed in Problem Symptoms Table | A |
| Fault is listed in Problem Symptoms Table | B |
A
B
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
Before checking for millimeter wave radar sensor beam axis misalignment, make sure that the radiator grille and front bumper are correctly installed and have not been damaged or modified.
Adjust the reflector height.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Place the reflector.
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Using the GTS, check the amount of misalignment.
| Tester Display |
|---|
| Front Beam Axis Misalignment Reading |
| Vertical Direction | -5 to 5 deg. |
| Horizontal Direction | -0.6 to 0.6 deg. |
| Result | Proceed to |
|---|---|
| The beam axis values are within specification | A |
| The beam axis values are not within specification | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Triangle Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(TRIANGLE TARGET)
Flat Surface Target: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>TARGET ADJUSTMENT(FLAT SURFACE TARGET)
Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>DRIVING ADJUSTMENT