Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2020.08
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
4WD Control ECU Communication Stop Mode Any of the following conditions are met:
·

Communication stop for "Four Wheel Drive Control" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication stop history for "Four Wheel Drive Control" is indicated on the "Communication Bus Check (Detail)" screen of the GTS. (The Lost Communication Time value for "Four Wheel Drive Control" is 6 or more.)

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table" are output.

Click here(Click here)


·

4WD ECU assembly branch line or connector

·

Power source circuit of 4WD ECU assembly

·

4WD ECU assembly ground circuit

·

4WD ECU assembly



WIRING DIAGRAM

for LHD


C366198E03
0.188,1.719 2.177,2 1.99,0.281 10 false No. 5 CAN Junction Connector 0.188,1.573 0.698,1.771 0.51,0.198 10 false F124 1.615,0.521 1.813,0.729 0.198,0.208 10 false 6 1.615,1.063 1.813,1.271 0.198,0.208 10 false 17 2.177,2.229 3.563,2.479 1.385,0.25 10 false from IG1-NO. 1 Relay 4.354,2.385 5.51,2.604 1.156,0.219 10 false ECU-IG1 NO. 2 5.802,0.625 6.365,0.813 0.563,0.188 10 false CANH 5.802,1.146 6.365,1.333 0.563,0.188 10 false CANL 5.802,2.198 6.365,2.385 0.563,0.188 10 false IG1 5.802,2.76 6.365,2.948 0.563,0.188 10 false GND 5.635,3.333 6.979,3.552 1.344,0.219 10 false 4WD ECU Assembly 5.646,3.177 6.156,3.375 0.51,0.198 10 false M77 5.604,0.521 5.802,0.729 0.198,0.208 10 false 6 5.594,1.073 5.792,1.281 0.198,0.208 10 false 5 5.583,2.125 5.781,2.333 0.198,0.208 10 false 3 5.583,2.656 5.781,2.865 0.198,0.208 10 false 4


for RHD


C366198E04
0.188,1.719 2.177,2 1.99,0.281 10 false No. 4 CAN Junction Connector 0.188,1.573 0.698,1.771 0.51,0.198 10 false F115 1.615,0.521 1.813,0.729 0.198,0.208 10 false 4 1.615,1.063 1.813,1.271 0.198,0.208 10 false 15 2.177,2.229 3.563,2.479 1.385,0.25 10 false from IG1-NO. 1 Relay 4.354,2.385 5.51,2.604 1.156,0.219 10 false ECU-IG1 NO. 2 5.802,0.625 6.365,0.813 0.563,0.188 10 false CANH 5.802,1.146 6.365,1.333 0.563,0.188 10 false CANL 5.802,2.198 6.365,2.385 0.563,0.188 10 false IG1 5.802,2.76 6.365,2.948 0.563,0.188 10 false GND 5.635,3.333 6.979,3.552 1.344,0.219 10 false 4WD ECU Assembly 5.646,3.177 6.156,3.375 0.51,0.198 10 false M77 5.604,0.521 5.802,0.729 0.198,0.208 10 false 6 5.594,1.073 5.792,1.281 0.198,0.208 10 false 5 5.583,2.125 5.781,2.333 0.198,0.208 10 false 3 5.583,2.656 5.781,2.865 0.198,0.208 10 false 4


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more.

Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (4WD ECU ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.


c.
C366213C01
1.5,0.583 2,0.833 0.5,0.25 0.542,1.979 0.333,2.75 true 0.76,1.979 1.167,2.75 true 0.052,0.073 0.365,0.229 0.313,0.156 10 false *a 1.615,0.604 2.01,0.781 0.396,0.177 10 false M77 0.156,2.771 0.625,2.948 0.469,0.177 10 false CANL 1.01,2.76 1.479,2.938 0.469,0.177 10 false CANH
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M77-6 (CANH) - M77-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Result
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINES OR CONNECTOR (4WD ECU ASSEMBLY)

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C366213C02
1.5,0.583 2,0.833 0.5,0.25 2.354,1.729 2.021,2.729 true 2.813,1.75 3.042,2.74 true 0.052,0.073 0.365,0.229 0.313,0.156 10 false *a 1.615,0.604 2.01,0.781 0.396,0.177 10 false M77 1.896,2.75 2.365,2.927 0.469,0.177 10 false IG1 2.917,2.75 3.385,2.927 0.469,0.177 10 false GND
*a Front view of wire harness connector
(to 4WD ECU Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M77-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
M77-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)